mirror of
https://github.com/openwrt/openwrt.git
synced 2024-12-29 18:19:02 +00:00
4070e2a64c
This target adds support for the StarFive JH7100 and JH7110 SoCs, based on 6.1, as well as a couple boards equipped with these. Specifications: SoCs: JH7100: - StarFive JH7100 dual-core RISC-V (U74, RC64GC) - additional monitoring (S7) and control (E24) cores - 2Mb L2 cache JH7110: - StarFive JH7110 quad-core RISC-V (U74, RV64GC) - additional monitoring (S7) and control (E24) cores - 2Mb L2 cache Boards: VisionFive1: - JH7100 @ 1GHz - Memory: 8Gb LPDDR4 - 4x USB3.0 - 1x GBit ethernet - AMPak 6236 wifi / bluetooth - audio - powered via USB-C VisionFive2: - JH7110 @ 1.5GHz - Memory: 2/4/8Gb DDR4 - 2x Gbit ethernet - 2x USB3.0 / 2x USB2.0 - eMMC / SDIO - various multimedia input/outputs (MIPI CSI, HDMI, audio) - M.2 key M slot - PoE support - powered via USB-C Installation: Standard SD-card installation via dd-ing the generated image to an SD-card of at least 256Mb. Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
54 lines
901 B
Plaintext
54 lines
901 B
Plaintext
#AP6212_NVRAM_V1.0_20140603
|
|
# 2.4 GHz, 20 MHz BW mode
|
|
|
|
# The following parameter values are just placeholders, need to be updated.
|
|
manfid=0x2d0
|
|
prodid=0x0726
|
|
vendid=0x14e4
|
|
devid=0x43e2
|
|
boardtype=0x0726
|
|
boardrev=0x1101
|
|
boardnum=22
|
|
macaddr=00:90:4c:c5:12:38
|
|
sromrev=11
|
|
boardflags=0x00404201
|
|
xtalfreq=26000
|
|
nocrc=1
|
|
ag0=255
|
|
aa2g=1
|
|
ccode=ALL
|
|
|
|
pa0itssit=0x20
|
|
extpagain2g=0
|
|
|
|
#PA parameters for 2.4GHz, measured at CHIP OUTPUT
|
|
pa2ga0=-168,7161,-820
|
|
AvVmid_c0=0x0,0xc8
|
|
cckpwroffset0=5
|
|
|
|
# PPR params
|
|
maxp2ga0=90
|
|
txpwrbckof=6
|
|
cckbw202gpo=0x5555
|
|
legofdmbw202gpo=0x77777777
|
|
mcsbw202gpo=0xaaaaaaaa
|
|
|
|
# OFDM IIR :
|
|
ofdmdigfilttype=7
|
|
# PAPD mode:
|
|
papdmode=2
|
|
|
|
il0macaddr=00:90:4c:c5:12:38
|
|
wl0id=0x431b
|
|
|
|
#OOB parameters
|
|
hostwake=0x40
|
|
hostrdy=0x41
|
|
usbrdy=0x03
|
|
usbrdydelay=100
|
|
deadman_to=0xffffffff
|
|
# muxenab: 0x1 for UART enable, 0x10 for Host awake
|
|
muxenab=0x10
|
|
# CLDO PWM voltage settings - 0x4 - 1.1 volt
|
|
#cldo_pwm=0x4
|