ExternalVendorCode/openwrt
1
0
Fork 0
mirror of https://github.com/openwrt/openwrt.git synced 2024-12-23 15:32:33 +00:00
Code Issues Actions 7 Packages Projects Releases Wiki Activity
8c986d2ab9
openwrt/target/linux/ramips/dts
History
Bjørn Mork 8c986d2ab9 ramips: mt7621: Add support for ZyXEL NR7101 
The ZyXEL NR7101 is an 802.3at PoE powered 5G outdoor (IP68) CPE
with integrated directional 5G/LTE antennas.

Specifications:

 - SoC: MediaTek MT7621AT
 - RAM: 256 MB
 - Flash: 128 MB MB NAND (MX30LF1G18AC)
 - WiFi: MediaTek MT7603E
 - Switch: 1 LAN port (Gigabiti)
 - 5G/LTE: Quectel RG502Q-EA connected by USB3 to SoC
 - SIM: 2 micro-SIM slots under transparent cover
 - Buttons: Reset, WLAN under same cover
 - LEDs: Multicolour green/red/yellow under same cover (visible)
 - Power: 802.3at PoE via LAN port

The device is built as an outdoor ethernet to 5G/LTE bridge or
router. The Wifi interface is intended for installation and/or
temporary management purposes only.

UART Serial:

57600N1
Located on populated 5 pin header J5:

 [o] GND
 [ ] key - no pin
 [o] RX
 [o] TX
 [o] 3.3V Vcc

Remove the SIM/button/LED cover, the WLAN button and 12 screws
holding the back plate and antenna cover together. The GPS antenna
is fixed to the cover, so be careful with the cable.  Remove 4
screws fixing the antenna board to the main board, again being
careful with the cables.

A bluetooth TTL adapter is recommended for permanent console
access, to keep the router water and dustproof. The 3.3V pin is
able to power such an adapter.

MAC addresses:

OpenWrt OEM   Address          Found as
lan     eth2  08:26:97:*:*:BC  Factory 0xe000 (hex), label
wlan0   ra0   08:26:97:*:*:BD  Factory 0x4 (hex)
wwan0   usb0  random

WARNING!!

ISP managed firmware might at any time update itself to a version
where all known workarounds have been disabled.  Never boot an ISP
managed firmware with a SIM in any of the slots if you intend to use
the router with OpenWrt. The bootloader lock can only be disabled with
root access to running firmware. The flash chip is physically
inaccessible without soldering.

Installation from OEM web GUI:

- Log in as "supervisor" on https://172.17.1.1/
- Upload OpenWrt initramfs-recovery.bin image on the
  Maintenance -> Firmware page
- Wait for OpenWrt to boot and ssh to root@192.168.1.1
- (optional) Copy OpenWrt to the recovery partition. See below
- Sysupgrade to the OpenWrt sysupgrade image and reboot

Installation from OEM ssh:

- Log in as "root" on 172.17.1.1 port 22022
- scp OpenWrt initramfs-recovery.bin image to 172.17.1.1:/tmp
- Prepare bootloader config by running:
    nvram setro uboot DebugFlag 0x1
    nvram setro uboot CheckBypass 0
    nvram commit
- Run "mtd_write -w write initramfs-recovery.bin Kernel" and reboot
- Wait for OpenWrt to boot and ssh to root@192.168.1.1
- (optional) Copy OpenWrt to the recovery partition. See below
- Sysupgrade to the OpenWrt sysupgrade image and reboot

Copying OpenWrt to the recovery partition:

- Verify that you are running a working OpenWrt recovery image
  from flash
- ssh to root@192.168.1.1 and run:
    fw_setenv CheckBypass 0
    mtd -r erase Kernel2
- Wait while the bootloader mirrors Image1 to Image2

NOTE: This should only be done after successfully booting the OpenWrt
  recovery image from the primary partition during installation.  Do
  not do this after having sysupgraded OpenWrt!  Reinstalling the
  recovery image on normal upgrades is not required or recommended.

Installation from Z-Loader:

- Halt boot by pressing Escape on console
- Set up a tftp server to serve the OpenWrt initramfs-recovery.bin
  image at 10.10.10.3
- Type "ATNR 1,initramfs-recovery.bin" at the "ZLB>" prompt
- Wait for OpenWrt to boot and ssh to root@192.168.1.1
- Sysupgrade to the OpenWrt sysupgrade image

NOTE: ATNR will write the recovery image to both primary and recovery
  partitions in one go.

Booting from RAM:

- Halt boot by pressing Escape on console
- Type "ATGU" at the "ZLB>" prompt to enter the U-Boot menu
- Press "4" to select "4: Entr boot command line interface."
- Set up a tftp server to serve the OpenWrt initramfs-recovery.bin
  image at 10.10.10.3
- Load it using "tftpboot 0x88000000 initramfs-recovery.bin"
- Boot with "bootm  0x8800017C" to skip the 380 (0x17C) bytes ZyXEL
  header

This method can also be used to RAM boot OEM firmware. The warning
regarding OEM applies!  Never boot an unknown OEM firmware, or any OEM
firmware with a SIM in any slot.

NOTE: U-Boot configuration is incomplete (on some devices?). You may
  have to configure a working mac address before running tftp using
   "setenv eth0addr <mac>"

Unlocking the bootloader:

If you are unebale to halt boot, then the bootloader is locked.

The OEM firmware locks the bootloader on every boot by setting
DebugFlag to 0.  Setting it to 1 is therefore only temporary
when OEM firmware is installed.

- Run "nvram setro uboot DebugFlag 0x1; nvram commit" in OEM firmware
- Run "fw_setenv DebugFlag 0x1" in OpenWrt

  NOTE:
    OpenWrt does this automatically on first boot if necessary

  NOTE2:
    Setting the flag to 0x1 avoids the reset to 0 in known OEM
    versions, but this might change.

  WARNING:
    Writing anything to flash while the bootloader is locked is
    considered extremely risky. Errors might cause a permanent
    brick!

Enabling management access from LAN:

Temporary workaround to allow installing OpenWrt if OEM firmware
has disabled LAN management:

- Connect to console
- Log in as "root"
- Run "iptables -I INPUT -i br0 -j ACCEPT"

Notes on the OEM/bootloader dual partition scheme

The dual partition scheme on this device uses Image2 as a recovery
image only. The device will always boot from Image1, but the
bootloader might copy Image2 to Image1 under specific conditions. This
scheme prevents repurposing of the space occupied by Image2 in any
useful way.

Validation of primary and recovery images is controlled by the
variables CheckBypass, Image1Stable, and Image1Try.

The bootloader sets CheckBypass to 0 and reboots if Image1 fails
validation.

If CheckBypass is 0 and Image1 is invalid then Image2 is copied to
Image1.

If CheckBypass is 0 and Image2 is invalid, then Image1 is copied to
Image2.

If CheckBypass is 1 then all tests are skipped and Image1 is booted
unconditionally.  CheckBypass is set to 1 after each successful
validation of Image1.

Image1Try is incremented if Image1Stable is 0, and Image2 is copied to
Image1 if Image1Try is 3 or larger.  But the bootloader only tests
Image1Try if CheckBypass is 0, which is impossible unless the booted
image sets it to 0 before failing.

The system is therefore not resilient against runtime errors like
failure to mount the rootfs, unless the kernel image sets CheckBypass
to 0 before failing. This is not yet implemented in OpenWrt.

Setting Image1Stable to 1 prevents the bootloader from updating
Image1Try on every boot, saving unnecessary writes to the environment
partition.

Keeping an OpenWrt initramfs recovery as Image2 is recommended
primarily to avoid unwanted OEM firmware boots on failure. Ref the
warning above. It enables console-less recovery in case of some
failures to boot from Image1.

Signed-off-by: Bjørn Mork <bjorn@mork.no>
Tested-by: Bjørn Mork <bjorn@mork.no>
(cherry picked from commit 2449a63208)
2021-06-10 17:09:35 +02:00
..
mt7620a_aigale_ai-br100.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
mt7620a_alfa-network_ac1200rm.dts ramips: replace full-text licenses by SPDX identifier 2021-02-05 18:18:00 +01:00
mt7620a_alfa-network_r36m-e4g.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
mt7620a_alfa-network_tube-e4g.dts ramips: drop redundant status for gpio/gpio0 2020-12-04 15:52:23 +01:00
mt7620a_asus_rp-n53.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
mt7620a_asus_rt-ac5x.dtsi ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
mt7620a_asus_rt-ac51u.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
mt7620a_asus_rt-ac54u.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
mt7620a_bdcom_wap2100-sk.dts ramips: drop redundant status for gpio/gpio0 2020-12-04 15:52:23 +01:00
mt7620a_buffalo_whr-300hp2.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
mt7620a_buffalo_whr-600d.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
mt7620a_buffalo_whr-1166d.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
mt7620a_cameo_810.dtsi treewide: add space before SPDX identifier 2020-11-25 19:34:13 +01:00
mt7620a_dlink_dch-m225.dts ramips: drop redundant status for gpio/gpio0 2020-12-04 15:52:23 +01:00
mt7620a_dlink_dir-510l.dts ramips: drop redundant status for gpio/gpio0 2020-12-04 15:52:23 +01:00
mt7620a_dlink_dir-810l.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
mt7620a_dlink_dwr-118-a1.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
mt7620a_dlink_dwr-118-a2.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
mt7620a_dlink_dwr-960.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
mt7620a_dovado_tiny-ac.dts ramips: drop redundant status for gpio/gpio0 2020-12-04 15:52:23 +01:00
mt7620a_edimax_br-6478ac-v2.dts ramips: replace full-text licenses by SPDX identifier 2021-02-05 18:18:00 +01:00
mt7620a_edimax_ew-747x.dtsi kernel: mtdsplit_uimage: replace "edimax, uimage" parser 2021-01-22 21:03:11 +01:00
mt7620a_edimax_ew-7476rpc.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
mt7620a_edimax_ew-7478ac.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
mt7620a_edimax_ew-7478apc.dts kernel: mtdsplit_uimage: replace "edimax, uimage" parser 2021-01-22 21:03:11 +01:00
mt7620a_engenius_esr600.dts ramips: do not enable unused GPIO controllers 2020-12-17 12:10:10 +01:00
mt7620a_fon_fon2601.dts kernel: mtdsplit_uimage: replace "fonfxc" and "sge" parsers 2021-01-22 21:03:11 +01:00
mt7620a_glinet_gl-mt300a.dts ramips: do not enable unused GPIO controllers 2020-12-17 12:10:10 +01:00
mt7620a_glinet_gl-mt300n.dts ramips: do not enable unused GPIO controllers 2020-12-17 12:10:10 +01:00
mt7620a_glinet_gl-mt750.dts ramips: do not enable unused GPIO controllers 2020-12-17 12:10:10 +01:00
mt7620a_head-weblink_hdrm200.dts ramips: drop redundant status for gpio/gpio0 2020-12-04 15:52:23 +01:00
mt7620a_hiwifi_hc5x61.dtsi ramips: do not enable unused GPIO controllers 2020-12-17 12:10:10 +01:00
mt7620a_hiwifi_hc5661.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
mt7620a_hiwifi_hc5761.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
mt7620a_hiwifi_hc5861.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
mt7620a_hnet_c108.dts ramips: replace full-text licenses by SPDX identifier 2021-02-05 18:18:00 +01:00
mt7620a_iodata_wn-ac733gr3.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
mt7620a_iodata_wn-ac1167gr.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
mt7620a_iptime_a104ns.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
mt7620a_iptime_a1004ns.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
mt7620a_iptime.dtsi ramips: increase spi-max-frequency for ipTIME mt7620 devices 2020-04-18 12:35:54 +08:00
mt7620a_kimax_u25awf-h1.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
mt7620a_lava_lr-25g001.dts ramips: drop redundant status for gpio/gpio0 2020-12-04 15:52:23 +01:00
mt7620a_lb-link_bl-w1200.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
mt7620a_lenovo_newifi-y1.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
mt7620a_lenovo_newifi-y1.dtsi ramips: drop redundant status for gpio/gpio0 2020-12-04 15:52:23 +01:00
mt7620a_lenovo_newifi-y1s.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
mt7620a_linksys_e1700.dts ramips: replace full-text licenses by SPDX identifier 2021-02-05 18:18:00 +01:00
mt7620a_microduino_microwrt.dts ramips: do not enable unused GPIO controllers 2020-12-17 12:10:10 +01:00
mt7620a_netgear_ex3x00_ex61xx.dtsi ramips: drop redundant status for gpio/gpio0 2020-12-04 15:52:23 +01:00
mt7620a_netgear_ex2700_wn3000rp-v3.dtsi ramips: move dts-v1 statement to top-level DTSI files 2020-09-25 23:26:40 +02:00
mt7620a_netgear_ex2700.dts ramips: replace full-text licenses by SPDX identifier 2021-02-05 18:18:00 +01:00
mt7620a_netgear_ex3700.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
mt7620a_netgear_ex6120.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
mt7620a_netgear_ex6130.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
mt7620a_netgear_wn3000rp-v3.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
mt7620a_netis_wf2770.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
mt7620a_ohyeah_oy-0001.dts ramips: do not enable unused GPIO controllers 2020-12-17 12:10:10 +01:00
mt7620a_phicomm_k2g.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
mt7620a_phicomm_psg1208.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
mt7620a_phicomm_psg1218.dtsi ramips: drop redundant status for gpio/gpio0 2020-12-04 15:52:23 +01:00
mt7620a_phicomm_psg1218a.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
mt7620a_phicomm_psg1218b.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
mt7620a_planex_cs-qr10.dts ramips: do not enable unused GPIO controllers 2020-12-17 12:10:10 +01:00
mt7620a_planex_db-wrt01.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
mt7620a_planex_mzk-750dhp.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
mt7620a_planex_mzk-ex300np.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
mt7620a_planex_mzk-ex750np.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
mt7620a_ralink_mt7620a-evb.dts ramips: move dts-v1 statement to top-level DTSI files 2020-09-25 23:26:40 +02:00
mt7620a_ralink_mt7620a-mt7530-evb.dts ramips: move dts-v1 statement to top-level DTSI files 2020-09-25 23:26:40 +02:00
mt7620a_ralink_mt7620a-mt7610e-evb.dts ramips: drop redundant status for gpio/gpio0 2020-12-04 15:52:23 +01:00
mt7620a_ralink_mt7620a-v22sg-evb.dts ramips: move dts-v1 statement to top-level DTSI files 2020-09-25 23:26:40 +02:00
mt7620a_sanlinking_d240.dts ramips: replace full-text licenses by SPDX identifier 2021-02-05 18:18:00 +01:00
mt7620a_sercomm_na930.dts ramips: do not enable unused GPIO controllers 2020-12-17 12:10:10 +01:00
mt7620a_tplink_archer-c2-v1.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
mt7620a_tplink_archer-c20-v1.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
mt7620a_tplink_archer-c20i.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
mt7620a_tplink_archer-c50-v1.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
mt7620a_tplink_archer-mr200.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
mt7620a_tplink_archer.dtsi ramips: increase SPI frequency for MT7620 Archer 2020-07-22 17:20:24 +02:00
mt7620a_tplink_re2x0-v1.dtsi ramips: add support for TP-Link RE210 v1 2020-03-09 21:47:56 +01:00
mt7620a_tplink_re200-v1.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
mt7620a_tplink_re210-v1.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
mt7620a_trendnet_tew-810dr.dts treewide: add space before SPDX identifier 2020-11-25 19:34:13 +01:00
mt7620a_wavlink_wl-wn530hg4.dts ramips: add support for Wavlink WL-WN530HG4 2020-10-27 21:20:16 +01:00
mt7620a_xiaomi_miwifi-mini.dts ramips: do not enable unused GPIO controllers 2020-12-17 12:10:10 +01:00
mt7620a_youku_yk1.dts ramips: fix mac addresses of Youku YK1 2021-05-14 23:32:22 +02:00
mt7620a_yukai_bocco.dts ramips: do not enable unused GPIO controllers 2020-12-17 12:10:10 +01:00
mt7620a_zbtlink_zbt-ape522ii.dts ramips: do not enable unused GPIO controllers 2020-12-17 12:10:10 +01:00
mt7620a_zbtlink_zbt-we826-16m.dts ramips: move dts-v1 statement to top-level DTSI files 2020-09-25 23:26:40 +02:00
mt7620a_zbtlink_zbt-we826-32m.dts ramips: move dts-v1 statement to top-level DTSI files 2020-09-25 23:26:40 +02:00
mt7620a_zbtlink_zbt-we826-e.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
mt7620a_zbtlink_zbt-we826.dtsi ramips: drop redundant status for gpio/gpio0 2020-12-04 15:52:23 +01:00
mt7620a_zbtlink_zbt-we1026-5g-16m.dts ramips: move dts-v1 statement to top-level DTSI files 2020-09-25 23:26:40 +02:00
mt7620a_zbtlink_zbt-we1026-5g.dtsi ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
mt7620a_zbtlink_zbt-we1026-h-32m.dts ramips: move dts-v1 statement to top-level DTSI files 2020-09-25 23:26:40 +02:00
mt7620a_zbtlink_zbt-we1026-h.dtsi ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
mt7620a_zbtlink_zbt-we1026.dtsi ramips: replace pinctrl property names 2020-04-12 22:29:17 +08:00
mt7620a_zte_q7.dts ramips: drop redundant status for gpio/gpio0 2020-12-04 15:52:23 +01:00
mt7620a_zyxel_keenetic-viva.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
mt7620a.dtsi ramips: move dts-v1 statement to top-level DTSI files 2020-09-25 23:26:40 +02:00
mt7620n_asus_rt-n12p.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
mt7620n_asus_rt-n14u.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
mt7620n_buffalo_wmr-300.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
mt7620n_comfast_cf-wr800n.dts ramips: drop redundant status for gpio/gpio0 2020-12-04 15:52:23 +01:00
mt7620n_dlink_dwr-116-a1.dts ramips: do not enable unused GPIO controllers 2020-12-17 12:10:10 +01:00
mt7620n_dlink_dwr-921-c1.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
mt7620n_dlink_dwr-922-e2.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
mt7620n_elecom_wrh-300cr.dts ramips: do not enable unused GPIO controllers 2020-12-17 12:10:10 +01:00
mt7620n_hootoo_ht-tm05.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
mt7620n_kimax_u35wf.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
mt7620n_kingston_mlw221.dts ramips: drop redundant status for gpio/gpio0 2020-12-04 15:52:23 +01:00
mt7620n_kingston_mlwg2.dts ramips: drop redundant status for gpio/gpio0 2020-12-04 15:52:23 +01:00
mt7620n_netgear_jwnr2010-v5.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
mt7620n_netgear_n300.dtsi ramips: add support for Netgear JWNR2010 v5 2020-08-06 16:56:07 +02:00
mt7620n_nexx_wt3020-4m.dts ramips: move dts-v1 statement to top-level DTSI files 2020-09-25 23:26:40 +02:00
mt7620n_nexx_wt3020-8m.dts ramips: move dts-v1 statement to top-level DTSI files 2020-09-25 23:26:40 +02:00
mt7620n_nexx_wt3020.dtsi ramips: do not enable unused GPIO controllers 2020-12-17 12:10:10 +01:00
mt7620n_ravpower_rp-wd03.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
mt7620n_sunvalley_filehub.dtsi kernel: mtdsplit_uimage: replace "openwrt, okli" parser 2021-01-22 21:03:11 +01:00
mt7620n_vonets_var11n-300.dts ramips: drop redundant status for gpio/gpio0 2020-12-04 15:52:23 +01:00
mt7620n_wrtnode_wrtnode.dts ramips: do not enable unused GPIO controllers 2020-12-17 12:10:10 +01:00
mt7620n_zbtlink_zbt-cpe102.dts ramips: do not enable unused GPIO controllers 2020-12-17 12:10:10 +01:00
mt7620n_zbtlink_zbt-wa05.dts ramips: do not enable unused GPIO controllers 2020-12-17 12:10:10 +01:00
mt7620n_zbtlink_zbt-we2026.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
mt7620n_zbtlink_zbt-wr8305rt.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
mt7620n_zyxel_keenetic-omni-ii.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
mt7620n_zyxel_keenetic-omni.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
mt7620n.dtsi ramips: move dts-v1 statement to top-level DTSI files 2020-09-25 23:26:40 +02:00
mt7621_adslr_g7.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
mt7621_afoundry_ew1200.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
mt7621_alfa-network_quad-e4g.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
mt7621_asiarf_ap7621-001.dts ramips: move dts-v1 statement to top-level DTSI files 2020-09-25 23:26:40 +02:00
mt7621_asiarf_ap7621-nv1.dts ramips: move dts-v1 statement to top-level DTSI files 2020-09-25 23:26:40 +02:00
mt7621_asiarf_ap7621.dtsi ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
mt7621_asus_rt-ac57u.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
mt7621_asus_rt-ac65p.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
mt7621_asus_rt-ac85p.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
mt7621_asus_rt-acx5p.dtsi ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
mt7621_asus_rt-n56u-b1.dts ramips: add support for ASUS RT-N56U B1 2020-11-28 20:51:50 +01:00
mt7621_buffalo_wsr-600dhp.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
mt7621_buffalo_wsr-1166dhp.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
mt7621_buffalo_wsr-2533dhpl.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
mt7621_cudy_wr1300.dts ramips: add support for Cudy WR1300 2021-02-09 13:58:18 +01:00
mt7621_d-team_newifi-d2.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
mt7621_d-team_pbr-m1.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
mt7621_dlink_dir-8xx-a1.dtsi kernel: mtdsplit_uimage: replace "fonfxc" and "sge" parsers 2021-01-22 21:03:11 +01:00
mt7621_dlink_dir-8xx-r1.dtsi ramips: add support for D-Link DIR-882 R1 2020-12-22 19:11:50 +01:00
mt7621_dlink_dir-8xx-x1.dtsi ramips: add support for D-Link DIR-882 R1 2020-12-22 19:11:50 +01:00
mt7621_dlink_dir-860l-b1.dts ramips: overwrite reset gpio properties in DIR-860L DTS 2021-02-24 20:23:52 +01:00
mt7621_dlink_dir-867-a1.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
mt7621_dlink_dir-878-a1.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
mt7621_dlink_dir-882-a1.dts ramips: add support for D-Link DIR-882 R1 2020-12-22 19:11:50 +01:00
mt7621_dlink_dir-882-r1.dts ramips: add support for D-Link DIR-882 R1 2020-12-22 19:11:50 +01:00
mt7621_dlink_dir-882-x1.dtsi ramips: add support for D-Link DIR-882 R1 2020-12-22 19:11:50 +01:00
mt7621_dlink_dir-1960-a1.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
mt7621_dlink_dir-2640-a1.dts ramips: add support for D-Link DIR-2640 A1 2020-11-11 17:35:10 +01:00
mt7621_dlink_dir-2660-a1.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
mt7621_dlink_dir-xx60-a1.dtsi kernel: mtdsplit_uimage: replace "fonfxc" and "sge" parsers 2021-01-22 21:03:11 +01:00
mt7621_edimax_ra21s.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
mt7621_edimax_re23s.dts kernel: mtdsplit_uimage: replace "edimax, uimage" parser 2021-01-22 21:03:11 +01:00
mt7621_edimax_rg21s.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
mt7621_edimax_rx21s.dtsi ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
mt7621_elecom_wrc-1167ghbk2-s.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
mt7621_elecom_wrc-1167gs2-b.dts ramips: add support for ELECOM WRC-1167GS2-B 2020-12-22 21:44:57 +01:00
mt7621_elecom_wrc-1167gst2.dts ramips: add support for ELECOM WRC-1167GST2 2020-12-22 21:44:57 +01:00
mt7621_elecom_wrc-1750gs.dts ramips: mt7621: create DTSI for ELECOM WRC GS devices with 2 PCI 2020-12-22 21:44:57 +01:00
mt7621_elecom_wrc-1750gst2.dts ramips: add support for ELECOM WRC-1750GST2 2021-03-22 21:07:34 +01:00
mt7621_elecom_wrc-1750gsv.dts ramips: mt7621: create DTSI for ELECOM WRC GS devices with 2 PCI 2020-12-22 21:44:57 +01:00
mt7621_elecom_wrc-1900gst.dts ramips: mt7621: create DTSI for ELECOM WRC GS devices with 2 PCI 2020-12-22 21:44:57 +01:00
mt7621_elecom_wrc-2533ghbk-i.dts ramips: add support for ELECOM WRC-2533GHBK-I 2021-01-29 15:32:07 +01:00
mt7621_elecom_wrc-2533gst2.dts ramips: mt7621: create DTSI for ELECOM WRC GS devices with 2 PCI 2020-12-22 21:44:57 +01:00
mt7621_elecom_wrc-2533gst.dts ramips: mt7621: create DTSI for ELECOM WRC GS devices with 2 PCI 2020-12-22 21:44:57 +01:00
mt7621_elecom_wrc-gs-1pci.dtsi ramips: add support for ELECOM WRC-1167GS2-B 2020-12-22 21:44:57 +01:00
mt7621_elecom_wrc-gs-2pci.dtsi ramips: mt7621: create DTSI for ELECOM WRC GS devices with 2 PCI 2020-12-22 21:44:57 +01:00
mt7621_elecom_wrc-gs.dtsi ramips: add support for ELECOM WRC-1167GS2-B 2020-12-22 21:44:57 +01:00
mt7621_firefly_firewrt.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
mt7621_gehua_ghl-r-001.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
mt7621_glinet_gl-mt1300.dts ramips: add support for GL.iNet GL-MT1300 2020-12-17 12:05:26 +01:00
mt7621_gnubee_gb-pc1.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
mt7621_gnubee_gb-pc2.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
mt7621_hiwifi_hc5962.dts treewide: use more descriptive names for concatenated partitions 2020-12-27 20:33:45 +01:00
mt7621_iodata_wn-ax1167gr2.dts ramips: move dts-v1 statement to top-level DTSI files 2020-09-25 23:26:40 +02:00
mt7621_iodata_wn-ax1167gr.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
mt7621_iodata_wn-ax2033gr.dts ramips: move dts-v1 statement to top-level DTSI files 2020-09-25 23:26:40 +02:00
mt7621_iodata_wn-dx1167r.dts ramips: move dts-v1 statement to top-level DTSI files 2020-09-25 23:26:40 +02:00
mt7621_iodata_wn-dx1200gr.dts ramips: add support for I-O DATA WN-DX1200GR 2021-02-07 21:58:51 +01:00
mt7621_iodata_wn-gx300gr.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
mt7621_iodata_wn-xx-xr.dtsi ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
mt7621_iodata_wnpr2600g.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
mt7621_iptime_a6ns-m.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
mt7621_iptime_a8004t.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
mt7621_jcg_jhr-ac876m.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
mt7621_jcg_y2.dts ramips: add support for JCG Y2 2021-02-09 13:10:33 +01:00
mt7621_lenovo_newifi-d1.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
mt7621_linksys_ea7xxx.dtsi ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
mt7621_linksys_ea7300-v1.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
mt7621_linksys_ea7300-v2.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
mt7621_linksys_ea7500-v2.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
mt7621_linksys_re6500.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
mt7621_mediatek_ap-mt7621a-v60.dts ramips: move dts-v1 statement to top-level DTSI files 2020-09-25 23:26:40 +02:00
mt7621_mediatek_mt7621-eval-board.dts ramips: move dts-v1 statement to top-level DTSI files 2020-09-25 23:26:40 +02:00
mt7621_mikrotik_routerboard-7xx.dtsi ramips: add support for MikroTik RouterBOARD 760iGS (hEX S) 2020-08-13 12:47:45 +02:00
mt7621_mikrotik_routerboard-750gr3.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
mt7621_mikrotik_routerboard-760igs.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
mt7621_mikrotik_routerboard-m11g.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
mt7621_mikrotik_routerboard-m33g.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
mt7621_mikrotik.dtsi ramips/mt7621: create common DTSI for Mikrotik devices 2020-08-13 12:47:45 +02:00
mt7621_mqmaker_witi.dts ramips: move dts-v1 statement to top-level DTSI files 2020-09-25 23:26:40 +02:00
mt7621_mtc_wr1201.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
mt7621_netgear_ex6150.dts ramips: overwrite reset gpio properties in EX6150 DTS 2021-02-20 09:39:58 +01:00
mt7621_netgear_r6220.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
mt7621_netgear_r6260.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
mt7621_netgear_r6350.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
mt7621_netgear_r6700-v2.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
mt7621_netgear_r6800.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
mt7621_netgear_r6850.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
mt7621_netgear_sercomm_ayx.dtsi ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
mt7621_netgear_sercomm_bzv.dtsi ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
mt7621_netgear_sercomm_chj.dtsi ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
mt7621_netgear_wac104.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
mt7621_netgear_wac124.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
mt7621_netgear_wndr3700-v5.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
mt7621_netis_wf2881.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
mt7621_phicomm_k2p.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
mt7621_planex_vr500.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
mt7621_samknows_whitebox-v8.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
mt7621_storylink_sap-g3200u3.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
mt7621_telco-electronics_x1.dts ramips: drop redundant status for gpio/gpio0 2020-12-04 15:52:23 +01:00
mt7621_thunder_timecloud.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
mt7621_totolink_a7000r.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
mt7621_totolink_x5000r.dts ramips: add support for TOTOLINK X5000R 2020-10-25 22:27:44 +08:00
mt7621_tplink_eap235-wall-v1.dts ramips: mt7621: add TP-Link EAP235-Wall support 2021-02-19 20:09:28 +01:00
mt7621_tplink_re350-v1.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
mt7621_tplink_re500-v1.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
mt7621_tplink_re650-v1.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
mt7621_tplink_rexx0-v1.dtsi ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
mt7621_ubnt_edgerouter-x-sfp.dts ramips: move dts-v1 statement to top-level DTSI files 2020-09-25 23:26:40 +02:00
mt7621_ubnt_edgerouter-x.dts ramips: move dts-v1 statement to top-level DTSI files 2020-09-25 23:26:40 +02:00
mt7621_ubnt_edgerouter-x.dtsi ramips: move redundant console setup to mt7621 SoC DTSI 2020-07-17 12:14:32 +02:00
mt7621_ubnt_unifi-6-lite.dts ramips: limit 5GHz channels for UniFi 6 Lite 2021-01-06 00:00:01 +01:00
mt7621_ubnt_unifi-nanohd.dts ramips: add support for Ubiquiti UniFi 6 Lite 2021-01-05 16:25:13 +01:00
mt7621_ubnt_unifi.dtsi ramips: add support for Ubiquiti UniFi 6 Lite 2021-01-05 16:25:13 +01:00
mt7621_unielec_u7621-01-16m.dts ramips: add support for UniElec U7621-01 2021-02-05 17:31:51 +01:00
mt7621_unielec_u7621-01.dtsi ramips: add support for UniElec U7621-01 2021-02-05 17:31:51 +01:00
mt7621_unielec_u7621-06-16m.dts ramips: replace full-text licenses by SPDX identifier 2021-02-05 18:18:00 +01:00
mt7621_unielec_u7621-06-64m.dts ramips: replace full-text licenses by SPDX identifier 2021-02-05 18:18:00 +01:00
mt7621_unielec_u7621-06.dtsi ramips: replace full-text licenses by SPDX identifier 2021-02-05 18:18:00 +01:00
mt7621_wavlink_wl-wn531a6.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
mt7621_wevo_11acnas.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
mt7621_wevo_w2914ns-v2.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
mt7621_wevo_w2914ns-v2.dtsi ramips: move redundant console setup to mt7621 SoC DTSI 2020-07-17 12:14:32 +02:00
mt7621_winstars_ws-wn583a6.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
mt7621_xiaomi_mi-router-3-pro.dts ramips: use full names for Xiaomi Mi Router devices 2020-12-08 17:18:57 +01:00
mt7621_xiaomi_mi-router-3g-v2.dts ramips: use full names for Xiaomi Mi Router devices 2020-12-08 17:18:57 +01:00
mt7621_xiaomi_mi-router-3g.dts ramips: mt7621: create DTSI for Xiaomi NAND devices 2021-01-21 22:52:02 +01:00
mt7621_xiaomi_mi-router-4.dts ramips: fix port labels for Xiaomi Mi Router 4 2021-01-21 22:56:43 +01:00
mt7621_xiaomi_mi-router-4a-3g-v2.dtsi ramips: reduce spi-max-frequency for Xiaomi MI Router 4AG 2021-04-18 12:04:38 +02:00
mt7621_xiaomi_mi-router-4a-gigabit.dts ramips: add Xiaomi Mi Router 4A Gigabit explicitly 2020-11-12 17:18:26 +01:00
mt7621_xiaomi_mi-router-ac2100.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
mt7621_xiaomi_nand_128m.dtsi ramips: mt7621: create DTSI for Xiaomi NAND devices 2021-01-21 22:52:02 +01:00
mt7621_xiaomi_redmi-router-ac2100.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
mt7621_xiaomi_router-ac2100.dtsi ramips: mt7621: create DTSI for Xiaomi NAND devices 2021-01-21 22:52:02 +01:00
mt7621_xiaoyu_xy-c5.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
mt7621_xzwifi_creativebox-v1.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
mt7621_youhua_wr1200js.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
mt7621_youku_yk-l2.dts ramips: remove redundant status for USB controllers 2020-12-07 14:22:00 +01:00
mt7621_zbtlink_zbt-we1326.dts ramips: move dts-v1 statement to top-level DTSI files 2020-09-25 23:26:40 +02:00
mt7621_zbtlink_zbt-we3526.dts ramips: move dts-v1 statement to top-level DTSI files 2020-09-25 23:26:40 +02:00
mt7621_zbtlink_zbt-wg2626.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
mt7621_zbtlink_zbt-wg3526-16m.dts ramips: move dts-v1 statement to top-level DTSI files 2020-09-25 23:26:40 +02:00
mt7621_zbtlink_zbt-wg3526-32m.dts ramips: move dts-v1 statement to top-level DTSI files 2020-09-25 23:26:40 +02:00
mt7621_zbtlink_zbt-wg3526.dtsi ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
mt7621_zio_freezio.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
mt7621_zyxel_nr7101.dts ramips: mt7621: Add support for ZyXEL NR7101 2021-06-10 17:09:35 +02:00
mt7621_zyxel_wap6805.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
mt7621.dtsi ramips: remove redundant status for USB controllers 2020-12-07 14:22:00 +01:00
mt7628an_alfa-network_awusfree1.dts ramips: replace full-text licenses by SPDX identifier 2021-02-05 18:18:00 +01:00
mt7628an_asus_rt-n1x.dtsi ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
mt7628an_asus_rt-n10p-v3.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
mt7628an_asus_rt-n11p-b1.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
mt7628an_asus_rt-n12-vp-b1.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
mt7628an_buffalo_wcr-1166ds.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
mt7628an_cudy_wr1000.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
mt7628an_d-team_pbr-d1.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
mt7628an_duzun_dm06.dts ramips: move dts-v1 statement to top-level DTSI files 2020-09-25 23:26:40 +02:00
mt7628an_elecom_wrc-1167fs.dts ramips: add support for ELECOM WRC-1167FS 2021-02-11 16:37:53 +01:00
mt7628an_glinet_gl-mt300n-v2.dts ramips: remove redundant status for USB controllers 2020-12-07 14:22:00 +01:00
mt7628an_glinet_microuter-n300.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
mt7628an_glinet_vixmini_microuter.dtsi ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
mt7628an_glinet_vixmini.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
mt7628an_hak5_wifi-pineapple-mk7.dts ramips: add support for the Hak5 WiFi Pineapple Mark 7 2020-11-18 23:49:34 +01:00
mt7628an_hilink_hlk-7628n.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
mt7628an_hilink_hlk-7688a.dts ramips: add support for Hi-Link HLK-7688A 2021-02-05 14:54:47 +01:00
mt7628an_hiwifi_hc5x61a.dtsi ramips: mt7628: update dts for upstream gpio-mt7621 driver 2020-04-12 22:27:18 +08:00
mt7628an_hiwifi_hc5661a.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
mt7628an_hiwifi_hc5761a.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
mt7628an_hiwifi_hc5861b.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
mt7628an_iptime_a3.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
mt7628an_iptime_a604m.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
mt7628an_iptime.dtsi ramips: replace pinctrl property names 2020-04-12 22:29:17 +08:00
mt7628an_jotale_js76x8-8m.dts ramips: move dts-v1 statement to top-level DTSI files 2020-09-25 23:26:40 +02:00
mt7628an_jotale_js76x8-16m.dts ramips: move dts-v1 statement to top-level DTSI files 2020-09-25 23:26:40 +02:00
mt7628an_jotale_js76x8-32m.dts ramips: move dts-v1 statement to top-level DTSI files 2020-09-25 23:26:40 +02:00
mt7628an_jotale_js76x8.dtsi ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
mt7628an_mediatek_linkit-smart-7688.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
mt7628an_mediatek_mt7628an-eval-board.dts ramips: move dts-v1 statement to top-level DTSI files 2020-09-25 23:26:40 +02:00
mt7628an_mercury_mac1200r-v2.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
mt7628an_netgear_r6xxx.dtsi ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
mt7628an_netgear_r6020.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
mt7628an_netgear_r6080.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
mt7628an_netgear_r6120.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
mt7628an_onion_omega2.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
mt7628an_onion_omega2.dtsi ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
mt7628an_onion_omega2p.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
mt7628an_rakwireless_rak633.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
mt7628an_ravpower_rp-wd009.dts ramips: remove redundant status for USB controllers 2020-12-07 14:22:00 +01:00
mt7628an_skylab_skw92a.dts ramips: remove redundant status for USB controllers 2020-12-07 14:22:00 +01:00
mt7628an_tama_w06.dts ramips: remove redundant status for USB controllers 2020-12-07 14:22:00 +01:00
mt7628an_totolink_a3.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
mt7628an_totolink_lr1200.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
mt7628an_tplink_8m-split-uboot.dtsi ramips: simplify status for ehci/ohci on mt7628 TP-Link devices 2020-12-07 14:22:00 +01:00
mt7628an_tplink_8m.dtsi ramips: simplify status for ehci/ohci on mt7628 TP-Link devices 2020-12-07 14:22:00 +01:00
mt7628an_tplink_archer-c20-v4.dts ramips: simplify status for ehci/ohci on mt7628 TP-Link devices 2020-12-07 14:22:00 +01:00
mt7628an_tplink_archer-c20-v5.dts ramips: simplify status for ehci/ohci on mt7628 TP-Link devices 2020-12-07 14:22:00 +01:00
mt7628an_tplink_archer-c50-v3.dts ramips: simplify status for ehci/ohci on mt7628 TP-Link devices 2020-12-07 14:22:00 +01:00
mt7628an_tplink_archer-c50-v4.dts ramips: simplify status for ehci/ohci on mt7628 TP-Link devices 2020-12-07 14:22:00 +01:00
mt7628an_tplink_re200-v2.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
mt7628an_tplink_re200-v3.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
mt7628an_tplink_re200-v4.dts ramips: add support for TP-Link RE200 v4 2020-10-20 03:01:13 +02:00
mt7628an_tplink_re200.dtsi ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
mt7628an_tplink_re220-v2.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
mt7628an_tplink_re305-v1.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
mt7628an_tplink_tl-mr3020-v3.dts ramips: remove redundant status for USB controllers 2020-12-07 14:22:00 +01:00
mt7628an_tplink_tl-mr3420-v5.dts ramips: simplify status for ehci/ohci on mt7628 TP-Link devices 2020-12-07 14:22:00 +01:00
mt7628an_tplink_tl-mr6400-v4.dts ramips: simplify status for ehci/ohci on mt7628 TP-Link devices 2020-12-07 14:22:00 +01:00
mt7628an_tplink_tl-mr6400-v5.dts ramips: simplify status for ehci/ohci on mt7628 TP-Link devices 2020-12-07 14:22:00 +01:00
mt7628an_tplink_tl-wa801nd-v5.dts ramips: simplify status for ehci/ohci on mt7628 TP-Link devices 2020-12-07 14:22:00 +01:00
mt7628an_tplink_tl-wr802n-v4.dts ramips: simplify status for ehci/ohci on mt7628 TP-Link devices 2020-12-07 14:22:00 +01:00
mt7628an_tplink_tl-wr840n-v4.dts ramips: simplify status for ehci/ohci on mt7628 TP-Link devices 2020-12-07 14:22:00 +01:00
mt7628an_tplink_tl-wr840n-v5.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
mt7628an_tplink_tl-wr841n-v13.dts ramips: simplify status for ehci/ohci on mt7628 TP-Link devices 2020-12-07 14:22:00 +01:00
mt7628an_tplink_tl-wr841n-v14.dts ramips: remove option to set WiFi LED via aliases 2020-10-02 14:51:57 +02:00
mt7628an_tplink_tl-wr842n-v5.dts ramips: simplify status for ehci/ohci on mt7628 TP-Link devices 2020-12-07 14:22:00 +01:00
mt7628an_tplink_tl-wr850n-v2.dts ramips: simplify status for ehci/ohci on mt7628 TP-Link devices 2020-12-07 14:22:00 +01:00
mt7628an_tplink_tl-wr902ac-v3.dts ramips: simplify status for ehci/ohci on mt7628 TP-Link devices 2020-12-07 14:22:00 +01:00
mt7628an_unielec_u7628-01-16m.dts ramips: replace full-text licenses by SPDX identifier 2021-02-05 18:18:00 +01:00
mt7628an_unielec_u7628-01.dtsi ramips: replace full-text licenses by SPDX identifier 2021-02-05 18:18:00 +01:00
mt7628an_vocore_vocore2-lite.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
mt7628an_vocore_vocore2.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
mt7628an_vocore_vocore2.dtsi ramips: replace pinctrl property names 2020-04-12 22:29:17 +08:00
mt7628an_wavlink_wl-wn570ha1.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
mt7628an_wavlink_wl-wn575a3.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
mt7628an_wavlink_wl-wn577a2.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
mt7628an_widora_neo-16m.dts ramips: move dts-v1 statement to top-level DTSI files 2020-09-25 23:26:40 +02:00
mt7628an_widora_neo-32m.dts ramips: move dts-v1 statement to top-level DTSI files 2020-09-25 23:26:40 +02:00
mt7628an_widora_neo.dtsi ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
mt7628an_wiznet_wizfi630s.dts treewide: add space before SPDX identifier 2020-11-25 19:34:13 +01:00
mt7628an_wrtnode_wrtnode2.dtsi ramips: dts: use generic node name for flash 2020-05-09 14:48:50 +02:00
mt7628an_wrtnode_wrtnode2p.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
mt7628an_wrtnode_wrtnode2r.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
mt7628an_xiaomi_mi-router-4.dtsi ramips: mt7628: create shared DTSI for Xiaomi Mi Router 4A/4C 2020-12-08 15:39:00 +01:00
mt7628an_xiaomi_mi-router-4a-100m.dts ramips: use full names for Xiaomi Mi Router devices 2020-12-08 17:18:57 +01:00
mt7628an_xiaomi_mi-router-4c.dts ramips: mt7628: create shared DTSI for Xiaomi Mi Router 4A/4C 2020-12-08 15:39:00 +01:00
mt7628an_xiaomi_miwifi-nano.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
mt7628an_zbtlink_zbt-we1226.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
mt7628an_zyxel_keenetic-extra-ii.dts ramips: remove redundant status for USB controllers 2020-12-07 14:22:00 +01:00
mt7628an.dtsi ramips: move dts-v1 statement to top-level DTSI files 2020-09-25 23:26:40 +02:00
rt2880_airlink101_ar670w.dts ramips: drop redundant status for gpio/gpio0 2020-12-04 15:52:23 +01:00
rt2880_airlink101_ar725w.dts ramips: drop redundant status for gpio/gpio0 2020-12-04 15:52:23 +01:00
rt2880_asus_rt-n15.dts ramips: drop redundant status for gpio/gpio0 2020-12-04 15:52:23 +01:00
rt2880_belkin_f5d8235-v1.dts ramips: drop redundant status for gpio/gpio0 2020-12-04 15:52:23 +01:00
rt2880_buffalo_wli-tx4-ag300n.dts ramips: drop redundant status for gpio/gpio0 2020-12-04 15:52:23 +01:00
rt2880_buffalo_wzr-agl300nh.dts ramips: drop redundant status for gpio/gpio0 2020-12-04 15:52:23 +01:00
rt2880_dlink_dap-1522-a1.dts ramips: drop redundant status for gpio/gpio0 2020-12-04 15:52:23 +01:00
rt2880_ralink_v11st-fe.dts ramips: drop redundant status for gpio/gpio0 2020-12-04 15:52:23 +01:00
rt2880.dtsi ramips: move dts-v1 statement to top-level DTSI files 2020-09-25 23:26:40 +02:00
rt3050_8devices_carambola.dts ramips: move dts-v1 statement to top-level DTSI files 2020-09-25 23:26:40 +02:00
rt3050_allnet_all0256n-4m.dts ramips: move dts-v1 statement to top-level DTSI files 2020-09-25 23:26:40 +02:00
rt3050_allnet_all0256n-8m.dts ramips: move dts-v1 statement to top-level DTSI files 2020-09-25 23:26:40 +02:00
rt3050_allnet_all0256n.dtsi ramips: drop redundant status for gpio/gpio0 2020-12-04 15:52:23 +01:00
rt3050_alphanetworks_asl26555-8m.dts ramips: move dts-v1 statement to top-level DTSI files 2020-09-25 23:26:40 +02:00
rt3050_alphanetworks_asl26555-16m.dts ramips: move dts-v1 statement to top-level DTSI files 2020-09-25 23:26:40 +02:00
rt3050_alphanetworks_asl26555.dtsi ramips: drop redundant status for gpio/gpio0 2020-12-04 15:52:23 +01:00
rt3050_arcwireless_freestation5.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
rt3050_asus_rt-g32-b1.dts ramips: move dts-v1 statement to top-level DTSI files 2020-09-25 23:26:40 +02:00
rt3050_asus_rt-n10-plus.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
rt3050_asus_wl-330n3g.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
rt3050_asus_wl-330n.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
rt3050_dlink_dcs-930.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
rt3050_dlink_dir-300-b1.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
rt3050_dlink_dir-600-b1.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
rt3050_dlink_dir-615-d.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
rt3050_dlink_dir-620-a1.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
rt3050_edimax_3g-6200n.dts kernel: mtdsplit_uimage: replace "edimax, uimage" parser 2021-01-22 21:03:11 +01:00
rt3050_edimax_3g-6200nl.dts kernel: mtdsplit_uimage: replace "edimax, uimage" parser 2021-01-22 21:03:11 +01:00
rt3050_huawei_d105.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
rt3050_jcg_jhr-n805r.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
rt3050_netcore_nw718.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
rt3050_sparklan_wcr-150gn.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
rt3050_teltonika_rut5xx.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
rt3050_tenda_w150m.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
rt3050_trendnet_tew-638apb-v2.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
rt3050.dtsi ramips: move dts-v1 statement to top-level DTSI files 2020-09-25 23:26:40 +02:00
rt3052_accton_wr6202.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
rt3052_alfa-network_w502u.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
rt3052_argus_atp-52b.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
rt3052_asiarf_awapn2403.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
rt3052_asus_rt-n13u.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
rt3052_aximcom_mr-102n.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
rt3052_aztech_hw550-3g.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
rt3052_belkin_f5d8235-v2.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
rt3052_buffalo_whr-g300n.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
rt3052_dlink_dap-1350.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
rt3052_engenius_esr-9753.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
rt3052_fon_fonera-20n.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
rt3052_hauppauge_broadway.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
rt3052_huawei_hg255d.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
rt3052_jcg_jhr-n825r.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
rt3052_jcg_jhr-n926r.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
rt3052_mofinetwork_mofi3500-3gn.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
rt3052_netgear_wnce2001.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
rt3052_nexaira_bc2.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
rt3052_omnima_miniembwifi.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
rt3052_petatel_psr-680w.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
rt3052_planex_mzk-w300nh2.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
rt3052_planex_mzk-wdpr.dts ramips: move dts-v1 statement to top-level DTSI files 2020-09-25 23:26:40 +02:00
rt3052_poray_ip2202.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
rt3052_prolink_pwh2004.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
rt3052_ralink_v22rw-2x2.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
rt3052_sitecom_wl-351.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
rt3052_skyline_sl-r7205.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
rt3052_tenda_3g300m.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
rt3052_tenda_w306r-v2.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
rt3052_unbranded_wr512-3gn-4m.dts ramips: move dts-v1 statement to top-level DTSI files 2020-09-25 23:26:40 +02:00
rt3052_unbranded_wr512-3gn-8m.dts ramips: move dts-v1 statement to top-level DTSI files 2020-09-25 23:26:40 +02:00
rt3052_unbranded_wr512-3gn.dtsi ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
rt3052_unbranded_xdx-rn502j.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
rt3052_upvel_ur-326n4g.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
rt3052_upvel_ur-336un.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
rt3052_zyxel_keenetic.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
rt3052_zyxel_nbg-419n.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
rt3352_allnet_all5002.dts ramips: drop redundant status for gpio/gpio0 2020-12-04 15:52:23 +01:00
rt3352_dlink_dir-615-h1.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
rt3352_dlink_dir-620-d1.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
rt3352_zte_mf283plus.dts ramips: add support for ZTE MF283+ 2021-06-02 21:29:16 +02:00
rt3352_zyxel_nbg-419n-v2.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
rt3352.dtsi ramips: move dts-v1 statement to top-level DTSI files 2020-09-25 23:26:40 +02:00
rt3662_asus_rt-n56u.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
rt3662_dlink_dir-645.dts ramips: fix logic level for DIR-645 buttons 2020-10-03 22:52:58 +02:00
rt3662_edimax_br-6475nd.dts kernel: mtdsplit_uimage: replace "edimax, uimage" parser 2021-01-22 21:03:11 +01:00
rt3662_engenius_esr600h.dts ramips: add support for Senao Engenius ESR600H 2020-12-22 19:11:50 +01:00
rt3662_loewe_wmdr-143n.dts ramips: move dts-v1 statement to top-level DTSI files 2020-09-25 23:26:40 +02:00
rt3662_omnima_hpm.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
rt3662_samsung_cy-swr1100.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
rt3883_belkin_f9k110x.dtsi ramips: do not enable unused GPIO controllers 2020-12-17 12:10:10 +01:00
rt3883_belkin_f9k1109v1.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
rt3883_sitecom_wlr-6000.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
rt3883_trendnet_tew-691gr.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
rt3883_trendnet_tew-692gr.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
rt3883.dtsi ramips: move dts-v1 statement to top-level DTSI files 2020-09-25 23:26:40 +02:00
rt5350_7links_px-4885-4m.dts ramips: move dts-v1 statement to top-level DTSI files 2020-09-25 23:26:40 +02:00
rt5350_7links_px-4885-8m.dts ramips: move dts-v1 statement to top-level DTSI files 2020-09-25 23:26:40 +02:00
rt5350_7links_px-4885.dtsi ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
rt5350_airlive_air3gii.dts ramips: drop redundant status for gpio/gpio0 2020-12-04 15:52:23 +01:00
rt5350_allnet_all5003.dts ramips: remove redundant status for USB controllers 2020-12-07 14:22:00 +01:00
rt5350_asiarf_awm002-evb-4m.dts ramips: move dts-v1 statement to top-level DTSI files 2020-09-25 23:26:40 +02:00
rt5350_asiarf_awm002-evb-8m.dts ramips: move dts-v1 statement to top-level DTSI files 2020-09-25 23:26:40 +02:00
rt5350_asiarf_awm002-evb.dtsi ramips: remove redundant status for USB controllers 2020-12-07 14:22:00 +01:00
rt5350_belkin_f7c027.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
rt5350_dlink_dcs-930l-b1.dts ramips: remove redundant status for USB controllers 2020-12-07 14:22:00 +01:00
rt5350_dlink_dir-300-b7.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
rt5350_dlink_dir-320-b1.dts ramips: remove redundant status for USB controllers 2020-12-07 14:22:00 +01:00
rt5350_dlink_dir-610-a1.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
rt5350_dlink_dwr-512-b.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
rt5350_easyacc_wizard-8800.dts ramips: do not enable unused GPIO controllers 2020-12-17 12:10:10 +01:00
rt5350_hame_mpr-a1.dts ramips: do not enable unused GPIO controllers 2020-12-17 12:10:10 +01:00
rt5350_hame_mpr-a2.dts ramips: remove redundant status for USB controllers 2020-12-07 14:22:00 +01:00
rt5350_hilink_hlk-rm04.dts ramips: remove redundant status for USB controllers 2020-12-07 14:22:00 +01:00
rt5350_hootoo_ht-tm02.dts ramips: remove redundant status for USB controllers 2020-12-07 14:22:00 +01:00
rt5350_intenso_memory2move.dts ramips: remove redundant status for USB controllers 2020-12-07 14:22:00 +01:00
rt5350_nexx_wt1520-4m.dts ramips: move dts-v1 statement to top-level DTSI files 2020-09-25 23:26:40 +02:00
rt5350_nexx_wt1520-8m.dts ramips: move dts-v1 statement to top-level DTSI files 2020-09-25 23:26:40 +02:00
rt5350_nexx_wt1520.dtsi ramips: remove redundant status for USB controllers 2020-12-07 14:22:00 +01:00
rt5350_nixcore_x1-8m.dts ramips: move dts-v1 statement to top-level DTSI files 2020-09-25 23:26:40 +02:00
rt5350_nixcore_x1-16m.dts ramips: move dts-v1 statement to top-level DTSI files 2020-09-25 23:26:40 +02:00
rt5350_nixcore_x1.dtsi ramips: remove redundant status for USB controllers 2020-12-07 14:22:00 +01:00
rt5350_olimex_rt5350f-olinuxino-evb.dts ramips: move dts-v1 statement to top-level DTSI files 2020-09-25 23:26:40 +02:00
rt5350_olimex_rt5350f-olinuxino.dts ramips: move dts-v1 statement to top-level DTSI files 2020-09-25 23:26:40 +02:00
rt5350_olimex_rt5350f-olinuxino.dtsi ramips: do not enable unused GPIO controllers 2020-12-17 12:10:10 +01:00
rt5350_omnima_miniembplug.dts ramips: remove redundant status for USB controllers 2020-12-07 14:22:00 +01:00
rt5350_planex_mzk-dp150n.dts ramips: do not enable unused GPIO controllers 2020-12-17 12:10:10 +01:00
rt5350_poray_m3.dts ramips: remove redundant status for USB controllers 2020-12-07 14:22:00 +01:00
rt5350_poray_m4-4m.dts ramips: move dts-v1 statement to top-level DTSI files 2020-09-25 23:26:40 +02:00
rt5350_poray_m4-8m.dts ramips: move dts-v1 statement to top-level DTSI files 2020-09-25 23:26:40 +02:00
rt5350_poray_m4.dtsi ramips: remove redundant status for USB controllers 2020-12-07 14:22:00 +01:00
rt5350_poray_x5.dts ramips: remove redundant status for USB controllers 2020-12-07 14:22:00 +01:00
rt5350_poray_x8.dts ramips: remove redundant status for USB controllers 2020-12-07 14:22:00 +01:00
rt5350_tenda_3g150b.dts ramips: do not enable unused GPIO controllers 2020-12-17 12:10:10 +01:00
rt5350_trendnet_tew-714tru.dts ramips: remove redundant status for USB controllers 2020-12-07 14:22:00 +01:00
rt5350_unbranded_a5-v11.dts ramips: do not enable unused GPIO controllers 2020-12-17 12:10:10 +01:00
rt5350_vocore_vocore-8m.dts ramips: move dts-v1 statement to top-level DTSI files 2020-09-25 23:26:40 +02:00
rt5350_vocore_vocore-16m.dts ramips: move dts-v1 statement to top-level DTSI files 2020-09-25 23:26:40 +02:00
rt5350_vocore_vocore.dtsi ramips: remove redundant status for USB controllers 2020-12-07 14:22:00 +01:00
rt5350_wansview_ncs601w.dts ramips: remove redundant status for USB controllers 2020-12-07 14:22:00 +01:00
rt5350_wiznet_wizfi630a.dts ramips: do not enable unused GPIO controllers 2020-12-17 12:10:10 +01:00
rt5350_zorlik_zl5900v2.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
rt5350_zyxel_keenetic-lite-b.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
rt5350_zyxel_keenetic-start.dts ramips: remove model name from LED labels 2020-10-02 14:51:57 +02:00
rt5350.dtsi ramips: move dts-v1 statement to top-level DTSI files 2020-09-25 23:26:40 +02:00