mirror of
https://github.com/openwrt/openwrt.git
synced 2024-12-28 09:39:00 +00:00
8486c677b8
This patch adds support for the MikroTik RouterBOARD 750 r2, marketed as hEX lite, a small indoor router with 5x 10/100 Mbps Ethernet ports, one with PoE in. The device was already supported by the ar71xx target. Specifications: - SoC: Qualcomm Atheros QCA9533 - Flash: 16 MB SPI NOR - RAM: 64 MB - Ethernet: 4x 10/100 Mbps LAN, 1x 10/100 Mbps WAN (PoE in) - LEDs: 5x Ethernet port activity (green), 1x user (green) - Buttons: 1x reset See https://mikrotik.com/product/RB750r2 for more details. Not working: - Serial port (already not working in ar71xx) Flashing: TFTP boot initramfs image and then perform sysupgrade. Only the "Internet" port will ask for an initramfs image. Follow common MikroTik procedure as in https://openwrt.org/toh/mikrotik/common. Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
95 lines
1.6 KiB
Plaintext
95 lines
1.6 KiB
Plaintext
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
|
|
|
#include "qca9533_mikrotik_routerboard-16m.dtsi"
|
|
|
|
/ {
|
|
compatible = "mikrotik,routerboard-lhg-hb", "qca,qca9533";
|
|
model = "MikroTik RouterBOARD LHG-HB platform";
|
|
|
|
aliases {
|
|
led-boot = &led_user;
|
|
led-failsafe = &led_user;
|
|
led-upgrade = &led_user;
|
|
led-running = &led_user;
|
|
};
|
|
|
|
leds {
|
|
compatible = "gpio-leds";
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&led_wan_pin>;
|
|
|
|
power {
|
|
label = "blue:power";
|
|
gpios = <&gpio 17 GPIO_ACTIVE_HIGH>;
|
|
default-state = "on";
|
|
};
|
|
|
|
led_user: user {
|
|
label = "green:user";
|
|
gpios = <&gpio 14 GPIO_ACTIVE_LOW>;
|
|
};
|
|
|
|
lan {
|
|
label = "green:lan";
|
|
gpios = <&gpio 4 GPIO_ACTIVE_LOW>;
|
|
};
|
|
|
|
wlan {
|
|
label = "green:wlan";
|
|
gpios = <&gpio 11 GPIO_ACTIVE_LOW>;
|
|
linux,default-trigger = "phy0tpt";
|
|
};
|
|
|
|
rssilow {
|
|
label = "green:rssilow";
|
|
gpios = <&gpio 9 GPIO_ACTIVE_LOW>;
|
|
};
|
|
|
|
rssimediumlow {
|
|
label = "green:rssimediumlow";
|
|
gpios = <&gpio 12 GPIO_ACTIVE_LOW>;
|
|
};
|
|
|
|
rssimediumhigh {
|
|
label = "green:rssimediumhigh";
|
|
gpios = <&gpio 13 GPIO_ACTIVE_LOW>;
|
|
};
|
|
|
|
/* The rssihigh LED GPIO 16 is shared with the reset button, so it remains
|
|
unregistered here to avoid conflict.
|
|
|
|
rssihigh {
|
|
label = "green:rssihigh";
|
|
gpios = <&gpio 16 GPIO_ACTIVE_LOW>;
|
|
};
|
|
*/
|
|
};
|
|
};
|
|
|
|
&wmac {
|
|
status = "okay";
|
|
|
|
qca,no-eeprom;
|
|
};
|
|
|
|
ð0 {
|
|
status = "okay";
|
|
|
|
phy-handle = <&swphy0>;
|
|
|
|
gmac-config {
|
|
device = <&gmac>;
|
|
switch-phy-swap = <1>;
|
|
};
|
|
};
|
|
|
|
ð1 {
|
|
compatible = "syscon", "simple-mfd";
|
|
};
|
|
|
|
&pinmux {
|
|
led_wan_pin: pinmux_led_wan_pin {
|
|
pinctrl-single,bits = <0x4 0x0 0xff>;
|
|
};
|
|
};
|