openwrt/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
David Bauer 897d55bcdf ipq40xx: add support for Teltonika RUTX50
Hardware
--------
CPU:     Qualcomm IPQ4018
RAM:     256M
Flash:   16MB SPI-NOR (W25Q128)
         128MB SPI-NAND (XTX)
WiFi:    2T2R (2GHz 802.11n ; 5 GHz 802.11ac)
ETH:     4x LAN ; 1x WAN (Gigabit)
CELL:    Quectel RG501Q 3G/4G/5G

UART: Available on the goldfinger connector (Pinout silkscreened)
      115200 8N1 3V3 - Only connect RX / TX / GND

Installation
------------

1. Enable SSH in the Teltonika UI
   (System --> Administration --> Access Control)

2. Check from which partition set the device is currently running from.

   $ cat /proc/boot_info/rootfs/primaryboot

   In case this output reads 0, install a Software update from Teltonika
   first. After upgrade completion, check this file now reads 1 before
   continuing.

2. Transfer the OpenWrt factory image to the device using scp. Use the
   same password (user root!) as used for the Web-UI.

   $ scp -O openwrt-factory.bin root@192.168.1.1:/tmp

3. Connect to the device using ssh as the root user.

4. Install OpenWrt by writing the factory image to flash.

   $ ubiformat /dev/mtd16 -y -f /tmp/openwrt-factory.bin

5. Instruct the bootloaer to boot from the first partition set.

   $ echo 0 > /proc/boot_info/rootfs/primaryboot
   $ cat /proc/boot_info/getbinary_bootconfig > /tmp/bootconfig.bin
   $ cat /proc/boot_info/getbinary_bootconfig1 > /tmp/bootconfig1.bin
   $ mtd write /tmp/bootconfig.bin /dev/mtd2
   $ mtd write /tmp/bootconfig1.bin /dev/mtd3

6. Reboot the device.

   $ reboot

Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit 844bb4bfad)
2023-07-26 15:37:56 +02:00

281 lines
9.4 KiB
Bash

#!/bin/sh
[ -e /lib/firmware/$FIRMWARE ] && exit 0
. /lib/functions/caldata.sh
board=$(board_name)
case "$FIRMWARE" in
"ath10k/cal-pci-0000:01:00.0.bin")
case "$board" in
meraki,mr33 |\
meraki,mr74)
caldata_extract_ubi "ART" 0x9000 0x844
caldata_valid "4408" || caldata_extract "ART" 0x9000 0x844
;;
esac
;;
"ath10k/pre-cal-pci-0000:01:00.0.bin")
case "$board" in
asus,map-ac2200)
caldata_extract_ubi "Factory" 0x9000 0x2f20
ln -sf /lib/firmware/ath10k/pre-cal-pci-0000\:00\:00.0.bin \
/lib/firmware/ath10k/QCA9888/hw2.0/board.bin
;;
asus,rt-ac42u)
caldata_extract_ubi "Factory" 0x9000 0x2f20
;;
avm,fritzrepeater-3000)
/usr/bin/fritz_cal_extract -i 1 -s 0x3D000 -e 0x212 -l 12064 -o /lib/firmware/$FIRMWARE $(find_mtd_chardev "urlader0") || \
/usr/bin/fritz_cal_extract -i 1 -s 0x3C800 -e 0x212 -l 12064 -o /lib/firmware/$FIRMWARE $(find_mtd_chardev "urlader0") || \
/usr/bin/fritz_cal_extract -i 1 -s 0x3C000 -e 0x212 -l 12064 -o /lib/firmware/$FIRMWARE $(find_mtd_chardev "urlader0") || \
/usr/bin/fritz_cal_extract -i 1 -s 0x3D000 -e 0x212 -l 12064 -o /lib/firmware/$FIRMWARE $(find_mtd_chardev "urlader1") || \
/usr/bin/fritz_cal_extract -i 1 -s 0x3C800 -e 0x212 -l 12064 -o /lib/firmware/$FIRMWARE $(find_mtd_chardev "urlader1") || \
/usr/bin/fritz_cal_extract -i 1 -s 0x3C000 -e 0x212 -l 12064 -o /lib/firmware/$FIRMWARE $(find_mtd_chardev "urlader1")
;;
linksys,ea8300 |\
linksys,mr8300)
caldata_extract "ART" 0x9000 0x2f20
# OEM assigns 4 sequential MACs
ath10k_patch_mac $(macaddr_setbit_la $(macaddr_add "$(cat /sys/class/net/eth0/address)" 4))
;;
netgear,rbr50|\
netgear,rbs50|\
netgear,srr60|\
netgear,srs60)
caldata_extract_mmc "0:ART" 0x9000 0x2f20
ath10k_patch_mac $(mmc_get_mac_binary ARTMTD 0x12)
;;
esac
;;
"ath10k/pre-cal-ahb-a000000.wifi.bin")
case "$board" in
qcom,ap-dk01.1-c1)
caldata_extract "ART" 0x1000 0x2f20
;;
asus,map-ac2200|\
asus,rt-ac42u|\
asus,rt-ac58u)
caldata_extract_ubi "Factory" 0x1000 0x2f20
;;
avm,fritzbox-4040)
/usr/bin/fritz_cal_extract -i 1 -s 0x400 -e 0x207 -l 12064 -o /lib/firmware/$FIRMWARE $(find_mtd_chardev "urlader_config")
;;
avm,fritzbox-7530 |\
avm,fritzrepeater-1200 |\
avm,fritzrepeater-3000)
/usr/bin/fritz_cal_extract -i 1 -s 0x3C000 -e 0x207 -l 12064 -o /lib/firmware/$FIRMWARE $(find_mtd_chardev "urlader0") || \
/usr/bin/fritz_cal_extract -i 1 -s 0x3C800 -e 0x207 -l 12064 -o /lib/firmware/$FIRMWARE $(find_mtd_chardev "urlader0") || \
/usr/bin/fritz_cal_extract -i 1 -s 0x3D000 -e 0x207 -l 12064 -o /lib/firmware/$FIRMWARE $(find_mtd_chardev "urlader0") || \
/usr/bin/fritz_cal_extract -i 1 -s 0x3C000 -e 0x207 -l 12064 -o /lib/firmware/$FIRMWARE $(find_mtd_chardev "urlader1") || \
/usr/bin/fritz_cal_extract -i 1 -s 0x3C800 -e 0x207 -l 12064 -o /lib/firmware/$FIRMWARE $(find_mtd_chardev "urlader1") || \
/usr/bin/fritz_cal_extract -i 1 -s 0x3D000 -e 0x207 -l 12064 -o /lib/firmware/$FIRMWARE $(find_mtd_chardev "urlader1")
;;
cellc,rtl30vw)
caldata_extract "0:ART" 0x1000 0x2f20
;;
devolo,magic-2-wifi-next)
caldata_extract "ART" 0x1000 0x2f20
ath10k_patch_mac $(mtd_get_mac_ascii APPSBLENV WiFiMacAddress0)
;;
dlink,dap-2610)
caldata_extract "ART" 0x1000 0x2f20
ath10k_patch_mac $(mtd_get_mac_ascii bdcfg wlanmac)
;;
engenius,emd1)
caldata_extract "0:ART" 0x1000 0x2f20
ath10k_patch_mac $(mtd_get_mac_ascii 0:APPSBLENV wlanaddr)
;;
engenius,emr3500)
caldata_extract "0:ART" 0x1000 0x2f20
ath10k_patch_mac $(mtd_get_mac_ascii 0:APPSBLENV ethaddr)
;;
engenius,ens620ext)
caldata_extract "ART" 0x1000 0x2f20
ath10k_patch_mac $(macaddr_add $(mtd_get_mac_ascii u-boot-env ethaddr) 2)
;;
extreme-networks,ws-ap3915i)
caldata_extract "ART" 0x1000 0x2f20
ath10k_patch_mac $(mtd_get_mac_ascii CFG1 RADIOADDR0)
;;
linksys,ea8300 |\
linksys,mr8300)
caldata_extract "ART" 0x1000 0x2f20
ath10k_patch_mac $(macaddr_add "$(cat /sys/class/net/eth0/address)" 2)
;;
meraki,mr33 |\
meraki,mr74)
caldata_extract_ubi "ART" 0x1000 0x2f20
caldata_valid "202f" || caldata_extract "ART" 0x1000 0x2f20
;;
mikrotik,cap-ac |\
mikrotik,hap-ac2 |\
mikrotik,hap-ac3 |\
mikrotik,hap-ac3-lte6-kit |\
mikrotik,wap-ac |\
mikrotik,wap-ac-lte |\
mikrotik,wap-r-ac)
wlan_data="/sys/firmware/mikrotik/hard_config/wlan_data"
( [ -f "$wlan_data" ] && caldata_sysfsload_from_file "$wlan_data" 0x0 0x2f20 ) || \
( [ -d "$wlan_data" ] && caldata_sysfsload_from_file "$wlan_data/data_0" 0x0 0x2f20 )
;;
netgear,rbr50|\
netgear,rbs50|\
netgear,srr60|\
netgear,srs60)
caldata_extract_mmc "0:ART" 0x1000 0x2f20
ath10k_patch_mac $(mmc_get_mac_binary ARTMTD 0x0)
;;
pakedge,wr-1)
caldata_extract "0:ART" 0x1000 0x2f20
ath10k_patch_mac $(macaddr_add $(get_mac_label) 2)
;;
teltonika,rutx10|\
teltonika,rutx50)
caldata_extract "0:ART" 0x1000 0x2f20
ath10k_patch_mac $(macaddr_add $(mtd_get_mac_binary "0:CONFIG" 0x0) 2)
;;
sony,ncp-hg100-cellular)
caldata_extract_mmc "0:ART" 0x1000 0x2f20
;;
zyxel,nbg6617 |\
zyxel,wre6606)
caldata_extract "ART" 0x1000 0x2f20
ath10k_patch_mac $(macaddr_add $(cat /sys/class/net/eth0/address) -2)
;;
esac
;;
"ath10k/pre-cal-ahb-a800000.wifi.bin")
case "$board" in
qcom,ap-dk01.1-c1)
caldata_extract "ART" 0x5000 0x2f20
;;
asus,map-ac2200|\
asus,rt-ac58u)
caldata_extract_ubi "Factory" 0x5000 0x2f20
;;
avm,fritzbox-4040)
/usr/bin/fritz_cal_extract -i 1 -s 0x400 -e 0x208 -l 12064 -o /lib/firmware/$FIRMWARE $(find_mtd_chardev "urlader_config")
;;
avm,fritzbox-7530 |\
avm,fritzrepeater-1200 |\
avm,fritzrepeater-3000)
/usr/bin/fritz_cal_extract -i 1 -s 0x3C800 -e 0x208 -l 12064 -o /lib/firmware/$FIRMWARE $(find_mtd_chardev "urlader0") || \
/usr/bin/fritz_cal_extract -i 1 -s 0x3D000 -e 0x208 -l 12064 -o /lib/firmware/$FIRMWARE $(find_mtd_chardev "urlader0") || \
/usr/bin/fritz_cal_extract -i 1 -s 0x3C000 -e 0x208 -l 12064 -o /lib/firmware/$FIRMWARE $(find_mtd_chardev "urlader0") || \
/usr/bin/fritz_cal_extract -i 1 -s 0x3C800 -e 0x208 -l 12064 -o /lib/firmware/$FIRMWARE $(find_mtd_chardev "urlader1") || \
/usr/bin/fritz_cal_extract -i 1 -s 0x3D000 -e 0x208 -l 12064 -o /lib/firmware/$FIRMWARE $(find_mtd_chardev "urlader1") || \
/usr/bin/fritz_cal_extract -i 1 -s 0x3C000 -e 0x208 -l 12064 -o /lib/firmware/$FIRMWARE $(find_mtd_chardev "urlader1")
;;
cellc,rtl30vw)
caldata_extract "0:ART" 0x5000 0x2f20
;;
devolo,magic-2-wifi-next)
caldata_extract "ART" 0x5000 0x2f20
ath10k_patch_mac $(mtd_get_mac_ascii APPSBLENV WiFiMacAddress1)
;;
dlink,dap-2610)
caldata_extract "ART" 0x5000 0x2f20
ath10k_patch_mac $(mtd_get_mac_ascii bdcfg wlanmac_a)
;;
engenius,emd1)
caldata_extract "0:ART" 0x5000 0x2f20
ath10k_patch_mac $(macaddr_add $(mtd_get_mac_ascii 0:APPSBLENV wlanaddr) 1)
;;
engenius,emr3500)
caldata_extract "0:ART" 0x5000 0x2f20
ath10k_patch_mac $(macaddr_add $(mtd_get_mac_ascii 0:APPSBLENV ethaddr) 1)
;;
engenius,ens620ext)
caldata_extract "ART" 0x5000 0x2f20
ath10k_patch_mac $(macaddr_add $(mtd_get_mac_ascii u-boot-env ethaddr) 3)
;;
extreme-networks,ws-ap3915i)
caldata_extract "ART" 0x5000 0x2f20
ath10k_patch_mac $(mtd_get_mac_ascii CFG1 RADIOADDR1)
;;
linksys,ea8300 |\
linksys,mr8300)
caldata_extract "ART" 0x5000 0x2f20
ath10k_patch_mac $(macaddr_add "$(cat /sys/class/net/eth0/address)" 3)
;;
meraki,mr33 |\
meraki,mr74)
caldata_extract_ubi "ART" 0x5000 0x2f20
caldata_valid "202f" || caldata_extract "ART" 0x5000 0x2f20
;;
mikrotik,cap-ac |\
mikrotik,hap-ac2 |\
mikrotik,hap-ac3 |\
mikrotik,hap-ac3-lte6-kit |\
mikrotik,sxtsq-5-ac |\
mikrotik,wap-ac |\
mikrotik,wap-ac-lte |\
mikrotik,wap-r-ac)
wlan_data="/sys/firmware/mikrotik/hard_config/wlan_data"
( [ -f "$wlan_data" ] && caldata_sysfsload_from_file "$wlan_data" 0x8000 0x2f20 ) || \
( [ -d "$wlan_data" ] && caldata_sysfsload_from_file "$wlan_data/data_2" 0x0 0x2f20 )
;;
netgear,rbr50|\
netgear,rbs50|\
netgear,srr60|\
netgear,srs60)
caldata_extract_mmc "0:ART" 0x5000 0x2f20
ath10k_patch_mac $(mmc_get_mac_binary ARTMTD 0xc)
;;
pakedge,wr-1)
caldata_extract "0:ART" 0x5000 0x2f20
ath10k_patch_mac $(macaddr_add $(get_mac_label) 4)
;;
teltonika,rutx10|\
teltonika,rutx50)
caldata_extract "0:ART" 0x5000 0x2f20
ath10k_patch_mac $(macaddr_add $(mtd_get_mac_binary "0:CONFIG" 0x0) 3)
;;
sony,ncp-hg100-cellular)
caldata_extract_mmc "0:ART" 0x5000 0x2f20
;;
zyxel,nbg6617 |\
zyxel,wre6606)
caldata_extract "ART" 0x5000 0x2f20
ath10k_patch_mac $(macaddr_add $(cat /sys/class/net/eth0/address) -1)
;;
esac
;;
"ath10k/QCA4019/hw1.0/board-ahb-a000000.wifi.bin")
case "$board" in
mikrotik,cap-ac |\
mikrotik,hap-ac2 |\
mikrotik,hap-ac3 |\
mikrotik,hap-ac3-lte6-kit |\
mikrotik,wap-ac |\
mikrotik,wap-ac-lte |\
mikrotik,wap-r-ac)
wlan_data="/sys/firmware/mikrotik/hard_config/wlan_data"
( [ -f "$wlan_data" ] && caldata_sysfsload_from_file "$wlan_data" 0x2f20 0x2f20 ) || \
( [ -d "$wlan_data" ] && caldata_sysfsload_from_file "$wlan_data/data_0" 0x2f20 0x2f20 )
;;
esac
;;
"ath10k/QCA4019/hw1.0/board-ahb-a800000.wifi.bin")
case "$board" in
mikrotik,cap-ac |\
mikrotik,hap-ac2 |\
mikrotik,hap-ac3 |\
mikrotik,hap-ac3-lte6-kit |\
mikrotik,sxtsq-5-ac |\
mikrotik,wap-ac |\
mikrotik,wap-ac-lte |\
mikrotik,wap-r-ac)
wlan_data="/sys/firmware/mikrotik/hard_config/wlan_data"
( [ -f "$wlan_data" ] && caldata_sysfsload_from_file "$wlan_data" 0xaf20 0x2f20 ) || \
( [ -d "$wlan_data" ] && caldata_sysfsload_from_file "$wlan_data/data_2" 0x2f20 0x2f20 )
;;
esac
;;
*)
exit 1
;;
esac