mirror of
https://github.com/openwrt/openwrt.git
synced 2024-12-29 18:19:02 +00:00
635f111148
In ath79, for several SoCs the console bootargs are defined to the very same value in every device's DTS. Consolidate these definitions in the SoC dtsi files and drop further redundant definitions elsewhere. The only device without any bootargs set has been OpenMesh OM5P-AC V2. This will now inherit the setting from qca955x.dtsi Note that while this tidies up master a lot, it might develop into a frequent pitfall for backports. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
180 lines
3.0 KiB
Plaintext
180 lines
3.0 KiB
Plaintext
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
|
|
|
#include <dt-bindings/gpio/gpio.h>
|
|
#include <dt-bindings/input/input.h>
|
|
|
|
#include "qca955x.dtsi"
|
|
|
|
/ {
|
|
aliases {
|
|
led-boot = &led_power;
|
|
led-failsafe = &led_power;
|
|
led-running = &led_power;
|
|
led-upgrade = &led_power;
|
|
mdio-gpio0 = &mdio2;
|
|
label-mac-device = ð0;
|
|
};
|
|
|
|
leds {
|
|
compatible = "gpio-leds";
|
|
|
|
led_power: power {
|
|
label = "tp-link:blue:power";
|
|
gpios = <&gpio 12 GPIO_ACTIVE_LOW>;
|
|
};
|
|
|
|
wlan2g {
|
|
label = "tp-link:blue:wlan2g";
|
|
gpios = <&gpio 13 GPIO_ACTIVE_LOW>;
|
|
linux,default-trigger = "phy1tpt";
|
|
};
|
|
|
|
wlan5g {
|
|
label = "tp-link:blue:wlan5g";
|
|
gpios = <&gpio 14 GPIO_ACTIVE_LOW>;
|
|
linux,default-trigger = "phy0tpt";
|
|
};
|
|
|
|
lan_link {
|
|
label = "tp-link:green:lan_link";
|
|
gpios = <&gpio 23 GPIO_ACTIVE_LOW>;
|
|
};
|
|
|
|
lan_data {
|
|
label = "tp-link:green:lan_data";
|
|
gpios = <&gpio 17 GPIO_ACTIVE_LOW>;
|
|
};
|
|
|
|
wps_blue {
|
|
label = "tp-link:blue:wps";
|
|
gpios = <&gpio 21 GPIO_ACTIVE_HIGH>;
|
|
};
|
|
|
|
wps_red {
|
|
label = "tp-link:red:wps";
|
|
gpios = <&gpio 22 GPIO_ACTIVE_HIGH>;
|
|
};
|
|
};
|
|
|
|
keys {
|
|
compatible = "gpio-keys";
|
|
|
|
reset {
|
|
label = "Reset button";
|
|
linux,code = <KEY_RESTART>;
|
|
gpios = <&gpio 18 GPIO_ACTIVE_LOW>;
|
|
debounce-interval = <60>;
|
|
};
|
|
|
|
leds {
|
|
label = "LED control button";
|
|
linux,code = <BTN_0>;
|
|
gpios = <&gpio 19 GPIO_ACTIVE_LOW>;
|
|
debounce-interval = <60>;
|
|
};
|
|
|
|
wps {
|
|
label = "WPS button";
|
|
linux,code = <KEY_WPS_BUTTON>;
|
|
gpios = <&gpio 20 GPIO_ACTIVE_LOW>;
|
|
debounce-interval = <60>;
|
|
};
|
|
};
|
|
|
|
mdio2: mdio {
|
|
compatible = "virtual,mdio-gpio";
|
|
|
|
gpios = <&gpio 3 GPIO_ACTIVE_HIGH>, /* MDC */
|
|
<&gpio 1 GPIO_ACTIVE_HIGH>; /* MDIO */
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
|
|
phy4: ethernet-phy@4 {
|
|
reg = <4>;
|
|
reset-gpios = <&gpio 11 GPIO_ACTIVE_LOW>;
|
|
};
|
|
};
|
|
};
|
|
|
|
&pcie0 {
|
|
status = "okay";
|
|
};
|
|
|
|
&uart {
|
|
status = "okay";
|
|
};
|
|
|
|
&gpio {
|
|
status = "okay";
|
|
};
|
|
|
|
&spi {
|
|
status = "okay";
|
|
num-cs = <1>;
|
|
|
|
flash@0 {
|
|
compatible = "jedec,spi-nor";
|
|
reg = <0>;
|
|
spi-max-frequency = <25000000>;
|
|
|
|
partitions {
|
|
compatible = "fixed-partitions";
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
|
|
partition@0 {
|
|
label = "u-boot";
|
|
reg = <0x000000 0x020000>;
|
|
read-only;
|
|
};
|
|
|
|
partition@20000 {
|
|
compatible = "tplink,firmware";
|
|
label = "firmware";
|
|
reg = <0x020000 0x5e0000>;
|
|
};
|
|
|
|
partition@600000 {
|
|
label = "partition-table";
|
|
reg = <0x600000 0x010000>;
|
|
read-only;
|
|
};
|
|
|
|
info: partition@610000 {
|
|
label = "info";
|
|
reg = <0x610000 0x020000>;
|
|
read-only;
|
|
};
|
|
|
|
partition@630000 {
|
|
label = "config";
|
|
reg = <0x630000 0x1c0000>;
|
|
read-only;
|
|
};
|
|
|
|
art: partition@7f0000 {
|
|
label = "art";
|
|
reg = <0x7f0000 0x010000>;
|
|
read-only;
|
|
};
|
|
};
|
|
};
|
|
};
|
|
|
|
ð0 {
|
|
status = "okay";
|
|
|
|
phy-handle = <&phy4>;
|
|
pll-data = <0xa6000000 0x00000101 0x00001616>;
|
|
|
|
mtd-mac-address = <&info 0x8>;
|
|
};
|
|
|
|
&wmac {
|
|
status = "okay";
|
|
|
|
mtd-cal-data = <&art 0x1000>;
|
|
mtd-mac-address = <&info 0x8>;
|
|
mtd-mac-address-increment = <(-1)>;
|
|
};
|