openwrt/target/linux/bcm27xx/patches-5.4/950-0423-ARM-dts-Remove-bcm2838-rpi-4-b.dts.patch
Álvaro Fernández Rojas a1383655cf bcm27xx: add linux 5.4 support
Tested on bcm2710 (Raspberry Pi 3B).

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2020-02-29 12:50:51 +01:00

163 lines
3.5 KiB
Diff

From 3c099a50b3d609206a86896405cfdc8a94cd7aa4 Mon Sep 17 00:00:00 2001
From: Phil Elwell <phil@raspberrypi.org>
Date: Wed, 29 Jan 2020 11:29:06 +0000
Subject: [PATCH] ARM: dts: Remove bcm2838-rpi-4-b.dts
Upstream are not going to use the bcm2838 identifier, so begin the
cleanup by removing the suggested upstream Pi 4 .dts file.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
---
arch/arm/boot/dts/Makefile | 1 -
arch/arm/boot/dts/bcm2838-rpi-4-b.dts | 134 --------------------------
2 files changed, 135 deletions(-)
delete mode 100644 arch/arm/boot/dts/bcm2838-rpi-4-b.dts
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -97,7 +97,6 @@ dtb-$(CONFIG_ARCH_BCM2835) += \
bcm2837-rpi-3-b.dtb \
bcm2837-rpi-3-b-plus.dtb \
bcm2837-rpi-cm3-io3.dtb \
- bcm2838-rpi-4-b.dtb \
bcm2835-rpi-zero.dtb \
bcm2835-rpi-zero-w.dtb
dtb-$(CONFIG_ARCH_BCM_5301X) += \
--- a/arch/arm/boot/dts/bcm2838-rpi-4-b.dts
+++ /dev/null
@@ -1,134 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0
-/dts-v1/;
-#include "bcm2838.dtsi"
-#include "bcm2835-rpi.dtsi"
-#include "bcm2838-rpi.dtsi"
-
-/ {
- compatible = "raspberrypi,4-model-b", "brcm,bcm2711";
- model = "Raspberry Pi 4 Model B";
-
- chosen {
- /* 8250 auxiliary UART instead of pl011 */
- stdout-path = "serial1:115200n8";
- };
-
- memory@0 {
- device_type = "memory";
- reg = <0x0 0x0 0x0>;
- };
-
- leds {
- act {
- gpios = <&gpio 42 GPIO_ACTIVE_HIGH>;
- };
-
- pwr {
- label = "PWR";
- gpios = <&expgpio 2 GPIO_ACTIVE_LOW>;
- };
- };
-
- wifi_pwrseq: wifi-pwrseq {
- compatible = "mmc-pwrseq-simple";
- reset-gpios = <&expgpio 1 GPIO_ACTIVE_LOW>;
- };
-
- sd_io_1v8_reg: sd_io_1v8_reg {
- status = "okay";
- compatible = "regulator-gpio";
- vin-supply = <&vdd_5v0_reg>;
- regulator-name = "vdd-sd-io";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <3300000>;
- regulator-boot-on;
- regulator-always-on;
- regulator-settling-time-us = <5000>;
-
- gpios = <&expgpio 4 GPIO_ACTIVE_HIGH>;
- states = <1800000 0x1
- 3300000 0x0>;
- };
-};
-
-&firmware {
- expgpio: gpio {
- compatible = "raspberrypi,firmware-gpio";
- gpio-controller;
- #gpio-cells = <2>;
- gpio-line-names = "BT_ON",
- "WL_ON",
- "PWR_LED_OFF",
- "GLOBAL_RESET",
- "VDD_SD_IO_SEL",
- "CAM_GPIO",
- "",
- "";
- status = "okay";
- };
-};
-
-&pwm1 {
- pinctrl-names = "default";
- pinctrl-0 = <&pwm0_gpio40 &pwm1_gpio41>;
- status = "okay";
-};
-
-/* SDHCI is used to control the SDIO for wireless */
-&sdhci {
- #address-cells = <1>;
- #size-cells = <0>;
- pinctrl-names = "default";
- pinctrl-0 = <&emmc_gpio34>;
- status = "okay";
- bus-width = <4>;
- non-removable;
- mmc-pwrseq = <&wifi_pwrseq>;
-
- brcmf: wifi@1 {
- reg = <1>;
- compatible = "brcm,bcm4329-fmac";
- };
-};
-
-/* EMMC2 is used to drive the SD card */
-&emmc2 {
- status = "okay";
- broken-cd;
- vqmmc-supply = <&sd_io_1v8_reg>;
-};
-
-&genet {
- phy-handle = <&phy1>;
- phy-mode = "rgmii-rxid";
- status = "okay";
-};
-
-&genet_mdio {
- phy1: ethernet-phy@1 {
- /* No PHY interrupt */
- reg = <0x1>;
- led-modes = <0x00 0x08>; /* link/activity link */
- };
-};
-
-/* uart0 communicates with the BT module */
-&uart0 {
- pinctrl-names = "default";
- pinctrl-0 = <&uart0_ctsrts_gpio30 &uart0_gpio32>;
- uart-has-rtscts;
- status = "okay";
-
- bluetooth {
- compatible = "brcm,bcm43438-bt";
- max-speed = <2000000>;
- shutdown-gpios = <&expgpio 0 GPIO_ACTIVE_HIGH>;
- };
-};
-
-/* uart1 is mapped to the pin header */
-&uart1 {
- pinctrl-names = "default";
- pinctrl-0 = <&uart1_gpio14>;
- status = "okay";
-};