mirror of
https://github.com/openwrt/openwrt.git
synced 2024-12-21 06:33:41 +00:00
8fb15ea52a
Copy dts/files/patches/configs from 5.10 to 5.15. Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com> [refresh with updated DGS-1210 dts files] Signed-off-by: Sander Vanheule <sander@svanheule.net>
381 lines
8.0 KiB
Plaintext
381 lines
8.0 KiB
Plaintext
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
|
|
|
#include "rtl839x.dtsi"
|
|
#include "rtl83xx_panasonic_mxxeg-pn28xx0k.dtsi"
|
|
|
|
#include <dt-bindings/interrupt-controller/irq.h>
|
|
|
|
/ {
|
|
compatible = "panasonic,m48eg-pn28480k", "realtek,rtl8393-soc";
|
|
model = "Panasonic Switch-M48eG PN28480K";
|
|
|
|
aliases {
|
|
led-boot = &led_status_eco_green;
|
|
led-failsafe = &led_status_eco_amber;
|
|
led-running = &led_status_eco_green;
|
|
led-upgrade = &led_status_eco_green;
|
|
};
|
|
|
|
fan: gpio-fan {
|
|
compatible = "gpio-fan";
|
|
gpios = <&gpio0 19 GPIO_ACTIVE_HIGH>;
|
|
/* the actual speeds (rpm) are unknown, just use dummy values */
|
|
gpio-fan,speed-map = <1 0>, <2 1>;
|
|
#cooling-cells = <2>;
|
|
};
|
|
|
|
/*
|
|
* sfp0/1/2/3 are "combo" port with each TP port (45/46/47/48),
|
|
* and they are connected to the RTL8218FB. Currently, there is
|
|
* no support for the chip and only TP ports work by the RTL8218B
|
|
* support.
|
|
*/
|
|
sfp0: sfp-p45 {
|
|
compatible = "sff,sfp";
|
|
i2c-bus = <&i2c0>;
|
|
tx-fault-gpio = <&gpio1 0 GPIO_ACTIVE_HIGH>;
|
|
tx-disable-gpio = <&gpio1 1 GPIO_ACTIVE_HIGH>;
|
|
mod-def0-gpio = <&gpio1 2 GPIO_ACTIVE_LOW>;
|
|
los-gpio = <&gpio1 3 GPIO_ACTIVE_HIGH>;
|
|
};
|
|
|
|
sfp1: sfp-p46 {
|
|
compatible = "sff,sfp";
|
|
i2c-bus = <&i2c1>;
|
|
tx-fault-gpio = <&gpio1 4 GPIO_ACTIVE_HIGH>;
|
|
tx-disable-gpio = <&gpio1 5 GPIO_ACTIVE_HIGH>;
|
|
mod-def0-gpio = <&gpio1 6 GPIO_ACTIVE_LOW>;
|
|
los-gpio = <&gpio1 7 GPIO_ACTIVE_HIGH>;
|
|
};
|
|
|
|
sfp2: sfp-p47 {
|
|
compatible = "sff,sfp";
|
|
i2c-bus = <&i2c2>;
|
|
tx-fault-gpio = <&gpio1 8 GPIO_ACTIVE_HIGH>;
|
|
tx-disable-gpio = <&gpio1 9 GPIO_ACTIVE_HIGH>;
|
|
mod-def0-gpio = <&gpio1 10 GPIO_ACTIVE_LOW>;
|
|
los-gpio = <&gpio1 11 GPIO_ACTIVE_HIGH>;
|
|
};
|
|
|
|
sfp3: sfp-p48 {
|
|
compatible = "sff,sfp";
|
|
i2c-bus = <&i2c3>;
|
|
tx-fault-gpio = <&gpio1 12 GPIO_ACTIVE_HIGH>;
|
|
tx-disable-gpio = <&gpio1 13 GPIO_ACTIVE_HIGH>;
|
|
mod-def0-gpio = <&gpio1 14 GPIO_ACTIVE_LOW>;
|
|
los-gpio = <&gpio1 15 GPIO_ACTIVE_HIGH>;
|
|
};
|
|
|
|
thermal-zones {
|
|
/*
|
|
* Zone for SoC temperature
|
|
*
|
|
* Fan speed:
|
|
*
|
|
* - 0-44 celsius: Low
|
|
* - 45-54 celsius: High
|
|
*/
|
|
cpu-thermal {
|
|
polling-delay-passive = <1000>;
|
|
polling-delay = <2000>;
|
|
|
|
thermal-sensors = <&tsens_soc>;
|
|
|
|
trips {
|
|
cpu_alert: trip-point {
|
|
temperature = <45000>;
|
|
hysteresis = <4000>;
|
|
type = "active";
|
|
};
|
|
|
|
cpu_crit {
|
|
temperature = <55000>;
|
|
hysteresis = <1000>;
|
|
type = "critical";
|
|
};
|
|
};
|
|
|
|
cooling-maps {
|
|
map {
|
|
trip = <&cpu_alert>;
|
|
cooling-device = <&fan 0 1>;
|
|
};
|
|
};
|
|
};
|
|
|
|
/*
|
|
* Zone for system temperature
|
|
*
|
|
* Fan speed:
|
|
*
|
|
* - 0-39 celsius: Low
|
|
* - 40-49 celsius: High
|
|
*
|
|
* Note: official recommended ranges of temperature on each
|
|
* fan speed setting:
|
|
*
|
|
* - Low speed : 0-40 celsius
|
|
* - High speed: 0-50 celsius
|
|
*
|
|
* (stock firmware doesn't support auto-selection of
|
|
* speed and need to be selected manually by user)
|
|
*/
|
|
sys-thermal {
|
|
polling-delay-passive = <1000>;
|
|
polling-delay = <2000>;
|
|
|
|
thermal-sensors = <&tsens_sys>;
|
|
|
|
trips {
|
|
sys_alert: trip-point {
|
|
temperature = <40000>;
|
|
hysteresis = <4000>;
|
|
type = "active";
|
|
};
|
|
|
|
sys_crit {
|
|
temperature = <50000>;
|
|
hysteresis = <2000>;
|
|
type = "critical";
|
|
};
|
|
};
|
|
|
|
cooling-maps {
|
|
map {
|
|
trip = <&sys_alert>;
|
|
cooling-device = <&fan 0 1>;
|
|
};
|
|
};
|
|
};
|
|
};
|
|
};
|
|
|
|
&leds {
|
|
led_status_eco_amber: led-5 {
|
|
label = "amber:status_eco";
|
|
gpios = <&gpio2 1 GPIO_ACTIVE_HIGH>;
|
|
color = <LED_COLOR_ID_AMBER>;
|
|
function = LED_FUNCTION_STATUS;
|
|
function-enumerator = <1>;
|
|
};
|
|
|
|
led_status_eco_green: led-6 {
|
|
label = "green:status_eco";
|
|
gpios = <&gpio2 2 GPIO_ACTIVE_HIGH>;
|
|
color = <LED_COLOR_ID_GREEN>;
|
|
function = LED_FUNCTION_STATUS;
|
|
function-enumerator = <2>;
|
|
};
|
|
};
|
|
|
|
&i2c_gpio_0 {
|
|
scl-gpios = <&gpio0 16 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
|
|
sda-gpios = <&gpio0 17 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
|
|
|
|
/* Microchip TCN75A (for SoC) */
|
|
tsens_soc: sensor@48 {
|
|
compatible = "microchip,tcn75";
|
|
reg = <0x48>;
|
|
#thermal-sensor-cells = <0>;
|
|
};
|
|
|
|
/* Microchip TCN75A (for System) */
|
|
tsens_sys: sensor@49 {
|
|
compatible = "microchip,tcn75";
|
|
reg = <0x49>;
|
|
#thermal-sensor-cells = <0>;
|
|
};
|
|
};
|
|
|
|
&i2c_gpio_1 {
|
|
scl-gpios = <&gpio0 14 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
|
|
sda-gpios = <&gpio0 15 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
|
|
};
|
|
|
|
&gpio2 {
|
|
interrupt-controller;
|
|
#interrupt-cells = <2>;
|
|
interrupt-parent = <&gpio0>;
|
|
interrupts = <18 IRQ_TYPE_EDGE_FALLING>;
|
|
|
|
/*
|
|
* GPIO12 (IO1_4): 5x RTL8218B + RTL8218FB
|
|
*
|
|
* This GPIO pin should be specified as "reset-gpio" in mdio node,
|
|
* but the current configuration of RTL8218B phy in the phy driver
|
|
* seems to be incomplete and RTL8218FB phy won't be configured on
|
|
* RTL8218D support. So, ethernet ports on these phys will be broken
|
|
* after hard-resetting.
|
|
* (RTL8218FB phy will be detected as RTL8218D by the phy driver)
|
|
* At the moment, configure this GPIO pin as gpio-hog to avoid breaking
|
|
* by resetting.
|
|
*/
|
|
ext_switch_reset {
|
|
gpio-hog;
|
|
gpios = <12 GPIO_ACTIVE_HIGH>;
|
|
output-high;
|
|
line-name = "ext-switch-reset";
|
|
};
|
|
};
|
|
|
|
&i2c_switch {
|
|
i2c0: i2c@0 {
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
reg = <0>;
|
|
};
|
|
|
|
i2c1: i2c@1 {
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
reg = <1>;
|
|
};
|
|
|
|
i2c2: i2c@2 {
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
reg = <2>;
|
|
};
|
|
|
|
i2c3: i2c@3 {
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
reg = <3>;
|
|
};
|
|
};
|
|
|
|
ðernet0 {
|
|
mdio-bus {
|
|
compatible = "realtek,rtl838x-mdio";
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
|
|
EXTERNAL_PHY(0)
|
|
EXTERNAL_PHY(1)
|
|
EXTERNAL_PHY(2)
|
|
EXTERNAL_PHY(3)
|
|
EXTERNAL_PHY(4)
|
|
EXTERNAL_PHY(5)
|
|
EXTERNAL_PHY(6)
|
|
EXTERNAL_PHY(7)
|
|
|
|
EXTERNAL_PHY(8)
|
|
EXTERNAL_PHY(9)
|
|
EXTERNAL_PHY(10)
|
|
EXTERNAL_PHY(11)
|
|
EXTERNAL_PHY(12)
|
|
EXTERNAL_PHY(13)
|
|
EXTERNAL_PHY(14)
|
|
EXTERNAL_PHY(15)
|
|
|
|
EXTERNAL_PHY(16)
|
|
EXTERNAL_PHY(17)
|
|
EXTERNAL_PHY(18)
|
|
EXTERNAL_PHY(19)
|
|
EXTERNAL_PHY(20)
|
|
EXTERNAL_PHY(21)
|
|
EXTERNAL_PHY(22)
|
|
EXTERNAL_PHY(23)
|
|
|
|
EXTERNAL_PHY(24)
|
|
EXTERNAL_PHY(25)
|
|
EXTERNAL_PHY(26)
|
|
EXTERNAL_PHY(27)
|
|
EXTERNAL_PHY(28)
|
|
EXTERNAL_PHY(29)
|
|
EXTERNAL_PHY(30)
|
|
EXTERNAL_PHY(31)
|
|
|
|
EXTERNAL_PHY(32)
|
|
EXTERNAL_PHY(33)
|
|
EXTERNAL_PHY(34)
|
|
EXTERNAL_PHY(35)
|
|
EXTERNAL_PHY(36)
|
|
EXTERNAL_PHY(37)
|
|
EXTERNAL_PHY(38)
|
|
EXTERNAL_PHY(39)
|
|
|
|
/* RTL8218FB */
|
|
EXTERNAL_PHY(40)
|
|
EXTERNAL_PHY(41)
|
|
EXTERNAL_PHY(42)
|
|
EXTERNAL_PHY(43)
|
|
EXTERNAL_PHY(44)
|
|
EXTERNAL_PHY(45)
|
|
EXTERNAL_PHY(46)
|
|
EXTERNAL_PHY(47)
|
|
};
|
|
};
|
|
|
|
&switch0 {
|
|
ports {
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
|
|
SWITCH_PORT(0, 1, qsgmii)
|
|
SWITCH_PORT(1, 2, qsgmii)
|
|
SWITCH_PORT(2, 3, qsgmii)
|
|
SWITCH_PORT(3, 4, qsgmii)
|
|
SWITCH_PORT(4, 5, qsgmii)
|
|
SWITCH_PORT(5, 6, qsgmii)
|
|
SWITCH_PORT(6, 7, qsgmii)
|
|
SWITCH_PORT(7, 8, qsgmii)
|
|
|
|
SWITCH_PORT(8, 9, qsgmii)
|
|
SWITCH_PORT(9, 10, qsgmii)
|
|
SWITCH_PORT(10, 11, qsgmii)
|
|
SWITCH_PORT(11, 12, qsgmii)
|
|
SWITCH_PORT(12, 13, qsgmii)
|
|
SWITCH_PORT(13, 14, qsgmii)
|
|
SWITCH_PORT(14, 15, qsgmii)
|
|
SWITCH_PORT(15, 16, qsgmii)
|
|
|
|
SWITCH_PORT(16, 17, qsgmii)
|
|
SWITCH_PORT(17, 18, qsgmii)
|
|
SWITCH_PORT(18, 19, qsgmii)
|
|
SWITCH_PORT(19, 20, qsgmii)
|
|
SWITCH_PORT(20, 21, qsgmii)
|
|
SWITCH_PORT(21, 22, qsgmii)
|
|
SWITCH_PORT(22, 23, qsgmii)
|
|
SWITCH_PORT(23, 24, qsgmii)
|
|
|
|
SWITCH_PORT(24, 25, qsgmii)
|
|
SWITCH_PORT(25, 26, qsgmii)
|
|
SWITCH_PORT(26, 27, qsgmii)
|
|
SWITCH_PORT(27, 28, qsgmii)
|
|
SWITCH_PORT(28, 29, qsgmii)
|
|
SWITCH_PORT(29, 30, qsgmii)
|
|
SWITCH_PORT(30, 31, qsgmii)
|
|
SWITCH_PORT(31, 32, qsgmii)
|
|
|
|
SWITCH_PORT(32, 33, qsgmii)
|
|
SWITCH_PORT(33, 34, qsgmii)
|
|
SWITCH_PORT(34, 35, qsgmii)
|
|
SWITCH_PORT(35, 36, qsgmii)
|
|
SWITCH_PORT(36, 37, qsgmii)
|
|
SWITCH_PORT(37, 38, qsgmii)
|
|
SWITCH_PORT(38, 39, qsgmii)
|
|
SWITCH_PORT(39, 40, qsgmii)
|
|
|
|
SWITCH_PORT(40, 41, qsgmii)
|
|
SWITCH_PORT(41, 42, qsgmii)
|
|
SWITCH_PORT(42, 43, qsgmii)
|
|
SWITCH_PORT(43, 44, qsgmii)
|
|
SWITCH_PORT(44, 45, qsgmii)
|
|
SWITCH_PORT(45, 46, qsgmii)
|
|
SWITCH_PORT(46, 47, qsgmii)
|
|
SWITCH_PORT(47, 48, qsgmii)
|
|
|
|
port@52 {
|
|
ethernet = <ðernet0>;
|
|
reg = <52>;
|
|
phy-mode = "internal";
|
|
|
|
fixed-link {
|
|
speed = <1000>;
|
|
full-duplex;
|
|
};
|
|
};
|
|
};
|
|
};
|