mirror of
https://github.com/openwrt/openwrt.git
synced 2024-12-23 15:32:33 +00:00
f61e754522
This is sold as a dual-band 802.11ac range extender. It has a sliding switch for Extender mode or Access Point mode, a WPS button, a recessed Reset button, a hard-power button, and a multitude of LED's, some multiplexed via an NXP 74AHC164D chip. The internal serial header pinout is Vcc, Tx, Rx, GND, with GND closest to the corner of the board. You may connect at 115200 bps, 8 data bits, no parity, 1 stop bit. Specification: - System-On-Chip: QCA9558 - CPU/Speed: 720 MHz - Flash-Chip: Winbond 25Q128FVSG - Flash size: 16 MiB - RAM: 128 MiB - Wireless No1: QCA9558 on-chip 2.4GHz 802.11bgn, 3x3 - Wireless No2: QCA99x0 chip 5GHz 802.11an+ac, 4x4 - PHY: Atheros AR8035-A Installation: If you can get to the stock firmware's firmware upgrade option, just feed it the factory.img and boot as usual. As an alternative, TFTP the factory.img to the bootloader. Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us> [whitespace fix in DTS and reorder of make variables] Signed-off-by: Petr Štetiar <ynezz@true.cz>
198 lines
4.9 KiB
Bash
198 lines
4.9 KiB
Bash
#!/bin/sh
|
|
|
|
. /lib/functions/k2t.sh
|
|
|
|
# xor multiple hex values of the same length
|
|
xor() {
|
|
local val
|
|
local ret="0x$1"
|
|
local retlen=${#1}
|
|
|
|
shift
|
|
while [ -n "$1" ]; do
|
|
val="0x$1"
|
|
ret=$((ret ^ val))
|
|
shift
|
|
done
|
|
|
|
printf "%0${retlen}x" "$ret"
|
|
}
|
|
|
|
ath10kcal_die() {
|
|
echo "ath10cal: " "$*"
|
|
exit 1
|
|
}
|
|
|
|
ath10kcal_from_file() {
|
|
local source=$1
|
|
local offset=$2
|
|
local count=$3
|
|
|
|
dd if=$source of=/lib/firmware/$FIRMWARE iflag=skip_bytes bs=$count skip=$offset count=1 2>/dev/null || \
|
|
ath10kcal_die "failed to extract calibration data from $source"
|
|
}
|
|
|
|
ath10kcal_extract() {
|
|
local part=$1
|
|
local offset=$2
|
|
local count=$3
|
|
local mtd
|
|
|
|
mtd=$(find_mtd_chardev $part)
|
|
[ -n "$mtd" ] || \
|
|
ath10kcal_die "no mtd device found for partition $part"
|
|
|
|
dd if=$mtd of=/lib/firmware/$FIRMWARE iflag=skip_bytes bs=$count skip=$offset count=1 2>/dev/null || \
|
|
ath10kcal_die "failed to extract calibration data from $mtd"
|
|
}
|
|
|
|
ath10kcal_patch_mac() {
|
|
local mac=$1
|
|
|
|
[ -z "$mac" ] && return
|
|
|
|
macaddr_2bin $mac | dd of=/lib/firmware/$FIRMWARE conv=notrunc oflag=seek_bytes bs=6 seek=6 count=1
|
|
}
|
|
|
|
ath10kcal_patch_mac_crc() {
|
|
local mac=$1
|
|
local mac_offset=6
|
|
local chksum_offset=2
|
|
local xor_mac
|
|
local xor_fw_mac
|
|
local xor_fw_chksum
|
|
|
|
xor_fw_mac=$(hexdump -v -n 6 -s $mac_offset -e '/1 "%02x"' /lib/firmware/$FIRMWARE)
|
|
xor_fw_mac="${xor_fw_mac:0:4} ${xor_fw_mac:4:4} ${xor_fw_mac:8:4}"
|
|
|
|
ath10kcal_patch_mac "$mac" && {
|
|
xor_mac=${mac//:/}
|
|
xor_mac="${xor_mac:0:4} ${xor_mac:4:4} ${xor_mac:8:4}"
|
|
|
|
xor_fw_chksum=$(hexdump -v -n 2 -s $chksum_offset -e '/1 "%02x"' /lib/firmware/$FIRMWARE)
|
|
xor_fw_chksum=$(xor $xor_fw_chksum $xor_fw_mac $xor_mac)
|
|
|
|
printf "%b" "\x${xor_fw_chksum:0:2}\x${xor_fw_chksum:2:2}" | \
|
|
dd of=/lib/firmware/$FIRMWARE conv=notrunc bs=1 seek=$chksum_offset count=2
|
|
}
|
|
}
|
|
|
|
[ -e /lib/firmware/$FIRMWARE ] && exit 0
|
|
|
|
. /lib/functions.sh
|
|
. /lib/functions/system.sh
|
|
|
|
board=$(board_name)
|
|
|
|
case "$FIRMWARE" in
|
|
"ath10k/cal-pci-0000:00:00.0.bin")
|
|
case $board in
|
|
devolo,dvl1200e|\
|
|
devolo,dvl1200i|\
|
|
devolo,dvl1750c|\
|
|
devolo,dvl1750e|\
|
|
devolo,dvl1750i)
|
|
ath10kcal_extract "art" 20480 2116
|
|
ath10kcal_patch_mac_crc $(macaddr_add $(mtd_get_mac_binary art 0) -1)
|
|
;;
|
|
dlink,dir-859-a1)
|
|
ath10kcal_extract "art" 20480 2116
|
|
ath10kcal_patch_mac $(mtd_get_mac_ascii devdata "wlan5mac")
|
|
;;
|
|
elecom,wrc-1750ghbk2-i)
|
|
ath10kcal_extract "ART" 20480 2116
|
|
;;
|
|
engenius,epg5000|\
|
|
iodata,wn-ac1167dgr|\
|
|
iodata,wn-ac1600dgr2)
|
|
ath10kcal_extract "art" 20480 2116
|
|
ath10kcal_patch_mac $(macaddr_add $(mtd_get_mac_ascii u-boot-env ethaddr) +1)
|
|
;;
|
|
engenius,ews511ap|\
|
|
glinet,gl-ar750s|\
|
|
glinet,gl-x750|\
|
|
tplink,re450-v2)
|
|
ath10kcal_extract "art" 20480 2116
|
|
ath10kcal_patch_mac $(macaddr_add $(cat /sys/class/net/eth0/address) +1)
|
|
;;
|
|
nec,wg800hp)
|
|
ath10kcal_extract "art" 20480 2116
|
|
ath10kcal_patch_mac_crc $(mtd_get_mac_text board_data 2176)
|
|
;;
|
|
ocedo,koala|\
|
|
ocedo,ursus)
|
|
ath10kcal_extract "art" 20480 2116
|
|
ath10kcal_patch_mac $(mtd_get_mac_binary art 12)
|
|
;;
|
|
openmesh,om5p-ac-v2)
|
|
ath10kcal_extract "ART" 20480 2116
|
|
ath10kcal_patch_mac $(macaddr_add $(cat /sys/class/net/eth0/address) +16)
|
|
;;
|
|
tplink,archer-c2-v3)
|
|
ath10kcal_extract "ART" 20480 2116
|
|
ath10kcal_patch_mac $(macaddr_add $(cat /sys/class/net/eth0/address) -1)
|
|
;;
|
|
tplink,archer-c5-v1|\
|
|
tplink,archer-c7-v2)
|
|
ath10kcal_extract "art" 20480 2116
|
|
ath10kcal_patch_mac $(macaddr_add $(cat /sys/class/net/eth1/address) -1)
|
|
;;
|
|
tplink,archer-a7-v5|\
|
|
tplink,archer-c7-v4|\
|
|
tplink,archer-c7-v5)
|
|
ath10kcal_extract "art" 20480 2116
|
|
ath10kcal_patch_mac $(macaddr_add $(cat /sys/class/net/eth0/address) -1)
|
|
;;
|
|
tplink,re350k-v1)
|
|
ath10kcal_extract "art" 20480 2116
|
|
ath10kcal_patch_mac $(macaddr_add $(cat /sys/class/net/eth0/address) +2)
|
|
;;
|
|
ubnt,unifiac-lite|\
|
|
ubnt,unifiac-mesh|\
|
|
ubnt,unifiac-mesh-pro|\
|
|
ubnt,lap-120|\
|
|
ubnt,nanobeam-ac|\
|
|
ubnt,nanostation-ac|\
|
|
ubnt,nanostation-ac-loco|\
|
|
ubnt,unifiac-pro)
|
|
ath10kcal_extract "EEPROM" 20480 2116
|
|
;;
|
|
yuncore,a770)
|
|
ath10kcal_extract "art" 20480 2116
|
|
;;
|
|
esac
|
|
;;
|
|
"ath10k/pre-cal-pci-0000:00:00.0.bin")
|
|
case $board in
|
|
nec,wg1200cr)
|
|
ath10kcal_extract "art" 20480 12064
|
|
ath10kcal_patch_mac_crc $(mtd_get_mac_ascii devdata wlan5mac)
|
|
ln -sf /lib/firmware/ath10k/pre-cal-pci-0000\:00\:00.0.bin \
|
|
/lib/firmware/ath10k/QCA9888/hw2.0/board.bin
|
|
;;
|
|
netgear,ex6400|\
|
|
netgear,ex7300)
|
|
ath10kcal_extract "caldata" 20480 12064
|
|
ath10kcal_patch_mac $(mtd_get_mac_binary caldata 12)
|
|
;;
|
|
phicomm,k2t)
|
|
ath10kcal_extract "art" 20480 12064
|
|
ath10kcal_patch_mac_crc $(k2t_get_mac "5g_mac")
|
|
ln -sf /lib/firmware/ath10k/pre-cal-pci-0000\:00\:00.0.bin \
|
|
/lib/firmware/ath10k/QCA9888/hw2.0/board.bin
|
|
;;
|
|
tplink,archer-c58-v1|\
|
|
tplink,archer-c59-v1|\
|
|
tplink,archer-c6-v2)
|
|
ath10kcal_extract "art" 20480 12064
|
|
ath10kcal_patch_mac_crc $(macaddr_add $(mtd_get_mac_binary mac 8) -1)
|
|
ln -sf /lib/firmware/ath10k/pre-cal-pci-0000\:00\:00.0.bin \
|
|
/lib/firmware/ath10k/QCA9888/hw2.0/board.bin
|
|
;;
|
|
esac
|
|
;;
|
|
*)
|
|
exit 1
|
|
;;
|
|
esac
|