openwrt/target/linux/ath79/dts/qca9558_ocedo_ursus.dts
David Bauer 654eec5a2d ath79: enable SGMII workaround for affected boards
These boards suffer from a sudden inability to establish a link on the
SGMII. Enable the workaround to fix the link when it dies.

Signed-off-by: David Bauer <mail@david-bauer.net>
2020-04-27 12:22:02 +02:00

150 lines
2.3 KiB
Plaintext

// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
/dts-v1/;
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>
#include "qca955x.dtsi"
/ {
compatible = "ocedo,ursus", "qca,qca9558";
model = "OCEDO Ursus";
chosen {
bootargs = "console=ttyS0,115200n8";
};
leds {
compatible = "gpio-leds";
wifi2 {
label = "ursus:green:wlan2g";
gpios = <&gpio 14 GPIO_ACTIVE_LOW>;
linux,default-trigger = "phy1tpt";
};
wifi5 {
label = "ursus:green:wlan5g";
gpios = <&gpio 15 GPIO_ACTIVE_LOW>;
linux,default-trigger = "phy0tpt";
};
};
};
&pcie1 {
status = "okay";
};
&uart {
status = "okay";
};
&pll {
clocks = <&extosc>;
};
&spi {
status = "okay";
num-cs = <1>;
flash@0 {
compatible = "jedec,spi-nor";
reg = <0>;
spi-max-frequency = <25000000>;
partitions {
compatible = "fixed-partitions";
#address-cells = <1>;
#size-cells = <1>;
uboot: partition@0 {
label = "u-boot";
reg = <0x000000 0x040000>;
read-only;
};
partition@40000 {
label = "u-boot-env";
reg = <0x040000 0x010000>;
};
partition@50000 {
compatible = "denx,uimage";
label = "firmware";
reg = <0x050000 0x740000>;
};
partition@790000 {
label = "vendor";
reg = <0x790000 0x740000>;
read-only;
};
partition@ed0000 {
label = "data";
reg = <0xed0000 0x110000>;
read-only;
};
partition@fe0000 {
label = "id";
reg = <0xfe0000 0x010000>;
read-only;
};
art: partition@ff0000 {
label = "art";
reg = <0xff0000 0x010000>;
read-only;
};
};
};
};
&wmac {
status = "okay";
mtd-cal-data = <&art 0x1000>;
mtd-mac-address = <&art 0x06>;
};
&mdio0 {
status = "okay";
phy1: ethernet-phy@1 {
reg = <1>;
};
phy2: ethernet-phy@2 {
reg = <2>;
at803x-override-sgmii-link-check;
};
};
&eth0 {
status = "okay";
mtd-mac-address = <&art 0x00>;
phy-mode = "rgmii-rxid";
phy-handle = <&phy1>;
pll-data = <0x8e000000 0x80000101 0x80001313>;
gmac_config: gmac-config {
device = <&gmac>;
rxdv-delay = <3>;
rxd-delay = <3>;
txen-delay = <0>;
txd-delay = <0>;
rgmii-enabled = <1>;
};
};
&eth1 {
status = "okay";
mtd-mac-address = <&art 0x12>;
phy-handle = <&phy2>;
pll-data = <0x3000101 0x101 0x1313>;
qca955x-sgmii-fixup;
};