mirror of
https://github.com/openwrt/openwrt.git
synced 2024-12-27 01:11:14 +00:00
a58826c34f
Innacomm W3400V6 is an xDSL B/G wireless router based on Broadcom BCM6328 SoC. Hardware: SoC: Broadcom BCM6328 CPU: BMIPS4350 V8.0, 320 MHz, 1 core Flash: SPI-NOR 8MB, MX25L6406E RAM: 64 MB Ethernet: 4x 10/100 Mbps Switch: Integrated Wireless: 802.11b/g, BCM4312 LEDs/Buttons: 9x / 2x Flash instruction, web UI: 1) Set a static IP on your computer compatible with 192.168.1.1, i.e 192.168.1.100 2) Connect the ethernet cable from your computer to the router. 3) Make sure the router is powered off. 4) Press the reset button, don't release it yet! 5) While pressing reset, power on the router. 6) Wait 10 seconds or more. Note: The power LED is red at first then turns to solid green when ready. 8) Release the reset button. 9) Browse to 192.168.1.1 10) Select .bin file. 10) Upgrade the image. 11) Wait for it to reboot. Signed-off-by: Sieng Piaw Liew <liew.s.piaw@gmail.com> [Ammend commit description, merge patches, DT improvements] Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
50 lines
1.6 KiB
Diff
50 lines
1.6 KiB
Diff
--- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
|
|
+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
|
|
@@ -3244,6 +3244,22 @@ void __init board_bcm963xx_init(void)
|
|
val &= MPI_CSBASE_BASE_MASK;
|
|
}
|
|
boot_addr = (u8 *)KSEG1ADDR(val);
|
|
+ pr_info("Boot address 0x%08x\n",(unsigned int)boot_addr);
|
|
+
|
|
+ /* BT Voyager 2500V (RTA1046VW PCB) has 8 Meg flash used as two */
|
|
+ /* banks of 4 Meg. The byte at 0xBF800000 identifies the back to use.*/
|
|
+ /* Loading firmware from the CFE Prompt always loads to Bank 0 */
|
|
+ /* Do an early check of CFE and then select bank 0 */
|
|
+
|
|
+ if (boot_addr == (u8 *)0xbf800000) {
|
|
+ u8 *tmp_boot_addr = (u8*)0xbfc00000;
|
|
+
|
|
+ bcm63xx_nvram_init(tmp_boot_addr + BCM963XX_NVRAM_OFFSET);
|
|
+ if (!strcmp(bcm63xx_nvram_get_name(), "V2500V_BB")) {
|
|
+ pr_info("V2500V: nvram bank 0\n");
|
|
+ boot_addr = tmp_boot_addr;
|
|
+ }
|
|
+ }
|
|
|
|
/* dump cfe version */
|
|
cfe = boot_addr + BCM963XX_CFE_VERSION_OFFSET;
|
|
--- a/arch/mips/bcm63xx/dev-flash.c
|
|
+++ b/arch/mips/bcm63xx/dev-flash.c
|
|
@@ -21,6 +21,7 @@
|
|
#include <linux/spi/spi.h>
|
|
#include <linux/spi/flash.h>
|
|
|
|
+#include <bcm63xx_board.h>
|
|
#include <bcm63xx_cpu.h>
|
|
#include <bcm63xx_dev_flash.h>
|
|
#include <bcm63xx_regs.h>
|
|
@@ -256,6 +257,13 @@ int __init bcm63xx_flash_register(void)
|
|
val = bcm_mpi_readl(MPI_CSBASE_REG(0));
|
|
val &= MPI_CSBASE_BASE_MASK;
|
|
|
|
+ /* BT Voyager 2500V has 8 Meg flash in two 4 Meg banks */
|
|
+ /* Loading from CFE always uses Bank 0 */
|
|
+ if (!strcmp(board_get_name(), "V2500V_BB")) {
|
|
+ pr_info("V2500V: Start in Bank 0\n");
|
|
+ val = val + 0x400000; // Select Bank 0 start address
|
|
+ }
|
|
+
|
|
mtd_resources[0].start = val;
|
|
mtd_resources[0].end = 0x1FFFFFFF;
|
|
}
|