mirror of
https://github.com/openwrt/openwrt.git
synced 2024-12-28 01:28:59 +00:00
7f7bf36ec5
The minew g1-c is a smart home gateway / BLE gateway. A Nordic nRF52832 is available via USB UART (cp210x) to support BLE. The LED ring is a ring of 24x ws2812b connect to a generic GPIO (unsupported). There is a small LED which is only visible when the device is open which will be used as LED until the ws2812b is supported. The board has also a micro sdcard/tfcard slot (untested). The Nordic nRF52832 exposes SWD over a 5pin header (GND, VCC, SWD, SWC, RST). The vendor uses an older OpenWrt version, sysupgrade can be used via serial or ssh. CPU: MT7628AN / 580MHz RAM: DDR2 128 MiB RAM Flash: SPI NOR 16 MiB W25Q128 Ethernet: 1x 100 mbit (Port 0) (PoE in) USB: USB hub, 2x external, 1x internal to USB UART Power: via micro usb or PoE 802.11af UART: 3.3V, 115200 8n1 Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
143 lines
2.1 KiB
Plaintext
143 lines
2.1 KiB
Plaintext
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
|
|
|
#include "mt7628an.dtsi"
|
|
|
|
#include <dt-bindings/gpio/gpio.h>
|
|
#include <dt-bindings/input/input.h>
|
|
|
|
/ {
|
|
model = "Minew G1-C";
|
|
compatible = "minew,g1-c", "mediatek,mt7628an-soc";
|
|
|
|
aliases {
|
|
led-boot = &led_system;
|
|
led-failsafe = &led_system;
|
|
led-running = &led_system;
|
|
led-upgrade = &led_system;
|
|
};
|
|
|
|
memory@0 {
|
|
device_type = "memory";
|
|
reg = <0x0 0x8000000>;
|
|
};
|
|
|
|
keys {
|
|
compatible = "gpio-keys-polled";
|
|
poll-interval = <20>;
|
|
|
|
reset {
|
|
label = "reset";
|
|
gpios = <&gpio 38 GPIO_ACTIVE_LOW>;
|
|
linux,code = <KEY_RESTART>;
|
|
};
|
|
};
|
|
|
|
leds {
|
|
compatible = "gpio-leds";
|
|
|
|
led_system: system {
|
|
label = "red:system";
|
|
gpios = <&gpio 43 GPIO_ACTIVE_HIGH>;
|
|
default-state = "on";
|
|
};
|
|
};
|
|
|
|
gpio-export {
|
|
compatible = "gpio-export";
|
|
#size-cells = <0>;
|
|
|
|
ws2812 {
|
|
gpio-export,name = "ws2812";
|
|
gpio-export,output = <1>;
|
|
gpios = <&gpio 11 GPIO_ACTIVE_HIGH>;
|
|
};
|
|
|
|
nrf_power {
|
|
gpio-export,name = "nrf_power";
|
|
gpio-export,output = <1>;
|
|
gpios = <&gpio 45 GPIO_ACTIVE_HIGH>;
|
|
};
|
|
};
|
|
};
|
|
|
|
&state_default {
|
|
gpio {
|
|
groups = "gpio";
|
|
function = "gpio";
|
|
};
|
|
|
|
p0led_an {
|
|
groups = "p0led_an";
|
|
function = "gpio";
|
|
};
|
|
|
|
uart1 {
|
|
groups = "uart1";
|
|
function = "gpio";
|
|
};
|
|
|
|
wdt {
|
|
groups = "wdt";
|
|
function = "gpio";
|
|
};
|
|
};
|
|
|
|
&spi0 {
|
|
status = "okay";
|
|
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&spi_pins>, <&spi_cs1_pins>;
|
|
|
|
m25p80@0 {
|
|
compatible = "jedec,spi-nor";
|
|
reg = <0>;
|
|
spi-max-frequency = <40000000>;
|
|
|
|
partitions {
|
|
compatible = "fixed-partitions";
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
|
|
partition@0 {
|
|
label = "u-boot";
|
|
reg = <0x0 0x30000>;
|
|
read-only;
|
|
};
|
|
|
|
partition@30000 {
|
|
label = "u-boot-env";
|
|
reg = <0x30000 0x10000>;
|
|
};
|
|
|
|
factory: partition@40000 {
|
|
label = "factory";
|
|
reg = <0x40000 0x10000>;
|
|
read-only;
|
|
};
|
|
|
|
partition@50000 {
|
|
compatible = "denx,uimage";
|
|
label = "firmware";
|
|
reg = <0x50000 0xfb0000>;
|
|
};
|
|
};
|
|
};
|
|
};
|
|
|
|
ðernet {
|
|
mtd-mac-address = <&factory 0x28>;
|
|
};
|
|
|
|
&esw {
|
|
mediatek,portmap = <0x3e>;
|
|
};
|
|
|
|
&wmac {
|
|
status = "okay";
|
|
};
|
|
|
|
&sdhci {
|
|
status = "okay";
|
|
mediatek,cd-high;
|
|
};
|