openwrt/target/linux/ramips/dts/mt7621_dlink_dir-xx60-a1.dtsi
Alan Luck e222c8054c ramips: fix and clean up D-Link MAC address
add back WIFI eprom addresses pointer in mt7621_dlink_dir-xx60-a1.dtsi
Change MAC address pointer from factory_e006 to factory_e000 + 3
	same as used in D-link firmware 1.11 DIR-1960-A1
	DIR-1960-A1,DIR-2640-A1,DIR-2660-A1,DIR-3060-A1

Clean-up MAC addresses in D-Link NOR devices DTS's
Change WIFI MAC Addressees to the same as NAND cousins macaddr_factory_e000 + ?
	as later devices don't have the MAC address in factory configuration
	same as used in D-Link firmware 1.30 DIR-878-A1
	DIR-867-A1,DIR-878-A1,DIR-878-R1,DIR-882-A1,DIR-882-R1,DIR-1935-A1

* D-link software differs between source of wan address

Signed-off-by: Alan Luck <luckyhome2008@gmail.com>
2024-02-22 22:53:30 +01:00

227 lines
3.7 KiB
Plaintext

// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
#include "mt7621.dtsi"
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>
#include <dt-bindings/leds/common.h>
/ {
aliases {
label-mac-device = &gmac0;
led-boot = &led_power_orange;
led-failsafe = &led_power_white;
led-running = &led_power_white;
led-upgrade = &led_net_orange;
};
keys {
compatible = "gpio-keys";
reset {
label = "reset";
gpios = <&gpio 15 GPIO_ACTIVE_LOW>;
linux,code = <KEY_RESTART>;
};
wps {
label = "wps";
gpios = <&gpio 18 GPIO_ACTIVE_LOW>;
linux,code = <KEY_WPS_BUTTON>;
};
};
leds: leds {
compatible = "gpio-leds";
led_power_orange: power_orange {
function = LED_FUNCTION_POWER;
color = <LED_COLOR_ID_ORANGE>;
gpios = <&gpio 8 GPIO_ACTIVE_LOW>;
};
led_power_white: power_white {
function = LED_FUNCTION_POWER;
color = <LED_COLOR_ID_WHITE>;
gpios = <&gpio 16 GPIO_ACTIVE_LOW>;
};
led_net_orange: net_orange {
label = "orange:net";
gpios = <&gpio 4 GPIO_ACTIVE_LOW>;
};
net_white {
label = "white:net";
gpios = <&gpio 3 GPIO_ACTIVE_LOW>;
};
};
};
&nand {
status = "okay";
partitions {
compatible = "fixed-partitions";
#address-cells = <1>;
#size-cells = <1>;
partition@0 {
label = "Bootloader";
reg = <0x0 0x80000>;
read-only;
};
partition@80000 {
label = "config";
reg = <0x80000 0x80000>;
read-only;
};
partition@100000 {
label = "factory";
reg = <0x100000 0x40000>;
read-only;
nvmem-layout {
compatible = "fixed-layout";
#address-cells = <1>;
#size-cells = <1>;
eeprom_factory_0: eeprom@0 {
reg = <0x0 0x4da8>;
};
eeprom_factory_8000: eeprom@8000 {
reg = <0x8000 0x4da8>;
};
macaddr_factory_e000: macaddr@e000 {
compatible = "mac-base";
reg = <0xe000 0x6>;
#nvmem-cell-cells = <1>;
};
};
};
partition@140000 {
label = "config2";
reg = <0x140000 0x40000>;
read-only;
};
partition@180000 {
label = "firmware";
compatible = "openwrt,uimage", "denx,uimage";
openwrt,padding = <96>;
reg = <0x180000 0x2800000>;
};
partition@2980000 {
label = "private";
reg = <0x2980000 0x2000000>;
read-only;
};
partition@4980000 {
label = "firmware2";
reg = <0x4980000 0x2800000>;
};
partition@7180000 {
label = "mydlink";
reg = <0x7180000 0x600000>;
read-only;
};
partition@7780000 {
label = "reserved";
reg = <0x7780000 0x880000>;
read-only;
};
};
};
&pcie {
status = "okay";
};
&pcie0 {
wifi0: wifi@0,0 {
compatible = "mediatek,mt76";
reg = <0x0000 0 0 0 0>;
nvmem-cells = <&eeprom_factory_0>, <&macaddr_factory_e000 1>;
nvmem-cell-names = "eeprom", "mac-address";
ieee80211-freq-limit = <2400000 2500000>;
led {
led-active-low;
};
};
};
&pcie1 {
wifi1: wifi@0,0 {
compatible = "mediatek,mt76";
reg = <0x0000 0 0 0 0>;
nvmem-cells = <&eeprom_factory_8000>, <&macaddr_factory_e000 2>;
nvmem-cell-names = "eeprom", "mac-address";
ieee80211-freq-limit = <5000000 6000000>;
led {
led-active-low;
};
};
};
&gmac0 {
nvmem-cells = <&macaddr_factory_e000 0>;
nvmem-cell-names = "mac-address";
};
&gmac1 {
status = "okay";
label = "wan";
phy-handle = <&ethphy4>;
nvmem-cells = <&macaddr_factory_e000 3>;
nvmem-cell-names = "mac-address";
};
&mdio {
ethphy4: ethernet-phy@4 {
reg = <4>;
};
};
&switch0 {
ports {
port@0 {
status = "okay";
label = "lan4";
};
port@1 {
status = "okay";
label = "lan3";
};
port@2 {
status = "okay";
label = "lan2";
};
port@3 {
status = "okay";
label = "lan1";
};
};
};
&state_default {
gpio {
groups = "i2c", "uart3", "jtag", "wdt";
function = "gpio";
};
};