openwrt/target/linux/lantiq/dts/ARV752DPW.dts
Mathias Kresin 18c64f41c7 treewide: fix button keys codes used in dts
Use keycodes that matches the intended use case based on the label.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-11-27 15:34:23 +01:00

238 lines
4.5 KiB
Plaintext

/dts-v1/;
#include "danube.dtsi"
#include <dt-bindings/input/input.h>
/ {
model = "ARV752DPW - Arcor 802";
chosen {
bootargs = "console=ttyLTQ0,115200 init=/etc/preinit";
};
aliases {
led-boot = &power_red;
led-failsafe = &power_blue;
led-running = &power_red;
led-internet = &internet_red;
led-usb = &umts;
led-wifi = &wifi;
};
memory@0 {
reg = <0x0 0x4000000>;
};
sram@1F000000 {
vmmc@107000 {
status = "okay";
gpios = <&gpiomm 1 GPIO_ACTIVE_HIGH>;
};
};
fpi@10000000 {
localbus@0 {
nor-boot@0 {
compatible = "lantiq,nor";
bank-width = <2>;
reg = <0 0x0 0x800000>;
#address-cells = <1>;
#size-cells = <1>;
partitions {
compatible = "fixed-partitions";
#address-cells = <1>;
#size-cells = <1>;
partition@0 {
label = "uboot";
reg = <0x00000 0x10000>;
read-only;
};
partition@10000 {
label = "uboot_env";
reg = <0x10000 0x10000>;
read-only;
};
partition@20000 {
label = "firmware";
reg = <0x20000 0x7d0000>;
};
boardconfig: partition@7f0000 {
label = "board_config";
reg = <0x7f0000 0x10000>;
read-only;
};
};
};
gpiomm: gpiomm@4000000 {
compatible = "lantiq,gpio-mm";
reg = <1 0x0 0x10 >;
#address-cells = <1>;
#size-cells = <1>;
#gpio-cells = <2>;
gpio-controller;
lantiq,shadow = <0x3>;
};
};
gpio: pinmux@E100B10 {
pinctrl-names = "default";
pinctrl-0 = <&state_default>;
state_default: pinmux {
ebu {
lantiq,groups = "ebu cs1";
lantiq,function = "ebu";
};
exin {
lantiq,groups = "exin1";
lantiq,function = "exin";
lantiq,pull = <2>;
lantiq,output = <0>;
};
pci_in {
lantiq,groups = "req2", "req1";
lantiq,function = "pci";
lantiq,open-drain = <1>;
lantiq,pull = <2>;
lantiq,output = <0>;
};
pci_out {
lantiq,groups = "gnt1";
lantiq,function = "pci";
lantiq,output = <1>;
};
pci_rst {
lantiq,pins = "io21";
lantiq,pull = <2>;
lantiq,output = <1>;
};
leds {
lantiq,pins = "io3", "io5", "io6", "io8";
lantiq,output = <1>;
lantiq,pull = <0>;
};
keys {
lantiq,pins = "io11", "io12", "io13", "io28";
lantiq,output = <0>;
lantiq,pull = <2>;
lantiq,open-drain = <1>;
};
};
};
ifxhcd@E101000 {
status = "okay";
gpios = <&gpiomm 0 GPIO_ACTIVE_HIGH>;
};
etop@E180000 {
phy-mode = "rmii";
mtd-mac-address = <&boardconfig 0x16>;
};
};
gpio-keys-polled {
compatible = "gpio-keys-polled";
#address-cells = <1>;
#size-cells = <0>;
poll-interval = <100>;
wps {
label = "wps";
gpios = <&gpio 11 GPIO_ACTIVE_LOW>;
linux,code = <KEY_WPS_BUTTON>;
};
restart {
label = "restart";
gpios = <&gpio 12 GPIO_ACTIVE_LOW>;
linux,code = <KEY_POWER>;
};
dsl {
label = "dsl";
gpios = <&gpio 13 GPIO_ACTIVE_LOW>;
linux,code = <BTN_0>;
};
reset {
label = "reset";
gpios = <&gpio 30 GPIO_ACTIVE_LOW>;
linux,code = <KEY_RESTART>;
};
};
gpio-leds {
compatible = "gpio-leds";
power_blue: power1 {
label = "arv752dpw:blue:power";
gpios = <&gpio 3 GPIO_ACTIVE_LOW>;
};
internet_red: internet {
label = "arv752dpw:red:internet";
gpios = <&gpio 4 GPIO_ACTIVE_LOW>;
};
message {
label = "arv752dpw:red:message";
gpios = <&gpio 5 GPIO_ACTIVE_LOW>;
};
power_red: power {
label = "arv752dpw:red:power";
gpios = <&gpio 6 GPIO_ACTIVE_LOW>;
default-state = "keep";
};
voice1 {
label = "arv752dpw:red:voice";
gpios = <&gpio 8 GPIO_ACTIVE_LOW>;
};
umts: umts {
label = "arv752dpw:red:umts";
gpios = <&gpiomm 3 GPIO_ACTIVE_LOW>;
};
wifi: wifi {
label = "arv752dpw:red:wifi";
gpios = <&gpiomm 4 GPIO_ACTIVE_LOW>;
};
fxs1 {
label = "arv752dpw:green:tae-n";
gpios = <&gpiomm 5 GPIO_ACTIVE_LOW>;
};
fxs2 {
label = "arv752dpw:green:tae-u";
gpios = <&gpiomm 6 GPIO_ACTIVE_LOW>;
};
fxo {
label = "arv752dpw:green:isdn";
gpios = <&gpiomm 7 GPIO_ACTIVE_LOW>;
};
internet2 {
label = "arv752dpw:blue:internet";
gpios = <&gpiomm 8 GPIO_ACTIVE_LOW>;
};
voice2 {
label = "arv752dpw:blue:voice";
gpios = <&gpiomm 9 GPIO_ACTIVE_LOW>;
};
};
};
&pci0 {
status = "okay";
lantiq,external-clock;
gpio-reset = <&gpio 21 GPIO_ACTIVE_HIGH>;
interrupt-map = <0x7000 0 0 1 &icu0 135>;
req-mask = <0x3>;
wifi@1814,0601 {
compatible = "pci1814,0601";
reg = <0x7000 0 0 0 0>;
ralink,mtd-eeprom = <&boardconfig 0x410>;
ralink,mtd-eeprom-swap;
};
};