mirror of
https://github.com/openwrt/openwrt.git
synced 2024-12-22 06:57:57 +00:00
635f111148
In ath79, for several SoCs the console bootargs are defined to the very same value in every device's DTS. Consolidate these definitions in the SoC dtsi files and drop further redundant definitions elsewhere. The only device without any bootargs set has been OpenMesh OM5P-AC V2. This will now inherit the setting from qca955x.dtsi Note that while this tidies up master a lot, it might develop into a frequent pitfall for backports. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
177 lines
2.8 KiB
Plaintext
177 lines
2.8 KiB
Plaintext
// SPDX-License-Identifier: GPL-1.0-or-later OR MIT
|
|
|
|
#include <dt-bindings/gpio/gpio.h>
|
|
#include <dt-bindings/input/input.h>
|
|
|
|
#include "ar7100.dtsi"
|
|
|
|
/ {
|
|
aliases {
|
|
led-boot = &led_user;
|
|
led-failsafe = &led_user;
|
|
led-running = &led_user;
|
|
};
|
|
|
|
leds {
|
|
compatible = "gpio-leds";
|
|
|
|
led_user: user {
|
|
label = "mikrotik:yellow:user";
|
|
gpios = <&gpio 4 GPIO_ACTIVE_HIGH>;
|
|
default-state = "on";
|
|
};
|
|
|
|
led1 {
|
|
label = "mikrotik:green:led1";
|
|
gpios = <&cpld_gpio 0 GPIO_ACTIVE_LOW>;
|
|
};
|
|
|
|
led2 {
|
|
label = "mikrotik:green:led2";
|
|
gpios = <&cpld_gpio 2 GPIO_ACTIVE_LOW>;
|
|
};
|
|
|
|
led3 {
|
|
label = "mikrotik:green:led3";
|
|
gpios = <&cpld_gpio 1 GPIO_ACTIVE_LOW>;
|
|
};
|
|
|
|
led4 {
|
|
label = "mikrotik:green:led4";
|
|
gpios = <&cpld_gpio 3 GPIO_ACTIVE_LOW>;
|
|
};
|
|
|
|
led5 {
|
|
label = "mikrotik:green:led5";
|
|
gpios = <&cpld_gpio 8 GPIO_ACTIVE_LOW>;
|
|
};
|
|
};
|
|
};
|
|
|
|
&uart {
|
|
status = "okay";
|
|
};
|
|
|
|
&gpio {
|
|
ngpios = <31>;
|
|
gpio-line-names =
|
|
"", "", "", "", "LED", "RDY", "", "MDC",
|
|
"MDIO", "", "", "", "", "", "", "",
|
|
"", "", "", "", "", "", "", "",
|
|
"", "", "", "", "", "", "", "";
|
|
};
|
|
|
|
&pcie0 {
|
|
status = "okay";
|
|
};
|
|
|
|
&spi {
|
|
status = "okay";
|
|
|
|
compatible = "mikrotik,rb4xx-spi";
|
|
|
|
flash@0 {
|
|
compatible = "pm25lv512", "jedec,spi-nor";
|
|
|
|
reg = <0>;
|
|
spi-max-frequency = <25000000>;
|
|
|
|
partitions {
|
|
compatible = "mikrotik,routerboot-partitions";
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
|
|
partition@0 {
|
|
label = "routerboot1";
|
|
reg = <0x0 0x0>;
|
|
read-only;
|
|
};
|
|
|
|
hard_config {
|
|
label = "hard_config";
|
|
read-only;
|
|
};
|
|
|
|
bios {
|
|
label = "bios";
|
|
size = <0x1000>;
|
|
read-only;
|
|
};
|
|
|
|
routerboot2 {
|
|
label = "routerboot2";
|
|
read-only;
|
|
};
|
|
|
|
soft_config {
|
|
label = "soft_config";
|
|
};
|
|
};
|
|
};
|
|
|
|
cpld@1 {
|
|
compatible = "mikrotik,rb4xx-cpld";
|
|
|
|
reg = <1>;
|
|
spi-max-frequency = <25000000>;
|
|
|
|
cpld_gpio: gpio {
|
|
compatible = "mikrotik,rb4xx-gpio";
|
|
|
|
base = <32>;
|
|
|
|
gpio-controller;
|
|
#gpio-cells = <2>;
|
|
gpio-line-names =
|
|
"LED1", "LED2", "LED3", "LED4",
|
|
"FAN", "ALE", "CLE", "nCE",
|
|
"LED5";
|
|
};
|
|
|
|
nand {
|
|
compatible = "mikrotik,rb4xx-nand";
|
|
|
|
gpios = <&cpld_gpio 5 GPIO_ACTIVE_HIGH>, // ALE
|
|
<&cpld_gpio 6 GPIO_ACTIVE_HIGH>, // CLE
|
|
<&cpld_gpio 7 GPIO_ACTIVE_HIGH>, // nCE
|
|
<&gpio 5 GPIO_ACTIVE_HIGH>; // RDY
|
|
|
|
partitions {
|
|
compatible = "fixed-partitions";
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
|
|
partition@0 {
|
|
label = "booter";
|
|
reg = <0x0000000 0x0040000>;
|
|
read-only;
|
|
};
|
|
|
|
partition@40000 {
|
|
label = "kernel";
|
|
reg = <0x0040000 0x0800000>;
|
|
};
|
|
|
|
partition@840000 {
|
|
label = "ubi";
|
|
reg = <0x0840000 0x77c0000>;
|
|
};
|
|
};
|
|
};
|
|
};
|
|
};
|
|
|
|
ð0 {
|
|
status = "okay";
|
|
|
|
phy-handle = <&phy0>;
|
|
};
|
|
|
|
&mdio0 {
|
|
status = "okay";
|
|
|
|
phy0: ethernet-phy@0 {
|
|
reg = <0>;
|
|
};
|
|
};
|