openwrt/target/linux/ath79/image/generic.mk
Sven Eckelmann d9a3af46d8 ath79: Add support for OpenMesh MR600 v2
Device specifications:
======================

* Qualcomm/Atheros AR9344 rev 2
* 560/450/225 MHz (CPU/DDR/AHB)
* 128 MB of RAM
* 16 MB of SPI NOR flash
  - 2x 7 MB available; but one of the 7 MB regions is the recovery image
* 2T2R 2.4 GHz Wi-Fi
* 2T2R 5 GHz Wi-Fi
* 8x GPIO-LEDs (6x wifi, 1x wps, 1x power)
* 1x GPIO-button (reset)
* external h/w watchdog (enabled by default))
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* 1x ethernet
  - AR8035 ethernet PHY (RGMII)
  - 10/100/1000 Mbps Ethernet
  - 802.3af POE
  - used as LAN interface
* 12-24V 1A DC
* internal antennas

Flashing instructions:
======================

Various methods can be used to install the actual image on the flash.
Two easy ones are:

ap51-flash
----------

The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the image to the u-boot when the device boots up.

initramfs from TFTP
-------------------

The serial console must be used to access the u-boot shell during bootup.
It can then be used to first boot up the initramfs image from a TFTP server
(here with the IP 192.168.1.21):

   setenv serverip 192.168.1.21
   setenv ipaddr 192.168.1.1
   tftpboot 0c00000 <filename-of-initramfs-kernel>.bin && bootm $fileaddr

The actual sysupgrade image can then be transferred (on the LAN port) to the
device via

  scp <filename-of-squashfs-sysupgrade>.bin root@192.168.1.1:/tmp/

On the device, the sysupgrade must then be started using

  sysupgrade -n /tmp/<filename-of-squashfs-sysupgrade>.bin

Signed-off-by: Sven Eckelmann <sven@narfation.org>
[rebase, add LED migration]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-01-19 15:39:36 +01:00

2137 lines
58 KiB
Makefile

include ./common-buffalo.mk
include ./common-engenius.mk
include ./common-netgear.mk
include ./common-tp-link.mk
include ./common-yuncore.mk
DEVICE_VARS += ADDPATTERN_ID ADDPATTERN_VERSION
DEVICE_VARS += SEAMA_SIGNATURE SEAMA_MTDBLOCK
DEVICE_VARS += KERNEL_INITRAMFS_PREFIX DAP_SIGNATURE
DEVICE_VARS += EDIMAX_HEADER_MAGIC EDIMAX_HEADER_MODEL
define Build/add-elecom-factory-initramfs
$(eval edimax_model=$(word 1,$(1)))
$(eval product=$(word 2,$(1)))
$(STAGING_DIR_HOST)/bin/mkedimaximg \
-b -s CSYS -m $(edimax_model) \
-f 0x70000 -S 0x01100000 \
-i $@ -o $@.factory
( \
echo -n -e "ELECOM\x00\x00$(product)" | dd bs=40 count=1 conv=sync; \
echo -n "0.00" | dd bs=16 count=1 conv=sync; \
dd if=$@.factory; \
) > $@.factory.new
if [ "$$(stat -c%s $@.factory.new)" -le $$(($(subst k,* 1024,$(subst m, * 1024k,$(IMAGE_SIZE))))) ]; then \
mv $@.factory.new $(BIN_DIR)/$(KERNEL_INITRAMFS_PREFIX)-factory.bin; \
else \
echo "WARNING: initramfs kernel image too big, cannot generate factory image" >&2; \
fi
endef
define Build/addpattern
-$(STAGING_DIR_HOST)/bin/addpattern -B $(ADDPATTERN_ID) \
-v v$(ADDPATTERN_VERSION) -i $@ -o $@.new
-mv "$@.new" "$@"
endef
define Build/append-md5sum-bin
$(STAGING_DIR_HOST)/bin/mkhash md5 $@ | sed 's/../\\\\x&/g' |\
xargs echo -ne >> $@
endef
define Build/cybertan-trx
@echo -n '' > $@-empty.bin
-$(STAGING_DIR_HOST)/bin/trx -o $@.new \
-f $(IMAGE_KERNEL) -F $@-empty.bin \
-x 32 -a 0x10000 -x -32 -f $@
-mv "$@.new" "$@"
-rm $@-empty.bin
endef
define Build/edimax-headers
$(eval edimax_magic=$(word 1,$(1)))
$(eval edimax_model=$(word 2,$(1)))
$(STAGING_DIR_HOST)/bin/edimax_fw_header -M $(edimax_magic) -m $(edimax_model)\
-v $(VERSION_DIST)$(firstword $(subst +, , $(firstword $(subst -, ,$(REVISION))))) \
-n "uImage" \
-i $(KDIR)/loader-$(DEVICE_NAME).uImage \
-o $@.uImage
$(STAGING_DIR_HOST)/bin/edimax_fw_header -M $(edimax_magic) -m $(edimax_model)\
-v $(VERSION_DIST)$(firstword $(subst +, , $(firstword $(subst -, ,$(REVISION))))) \
-n "rootfs" \
-i $@ \
-o $@.rootfs
cat $@.uImage $@.rootfs > $@
rm -rf $@.uImage $@.rootfs
endef
define Build/mkdapimg2
$(STAGING_DIR_HOST)/bin/mkdapimg2 \
-i $@ -o $@.new \
-s $(DAP_SIGNATURE) \
-v $(VERSION_DIST)-$(firstword $(subst +, , \
$(firstword $(subst -, ,$(REVISION))))) \
-r Default \
$(if $(1),-k $(1))
mv $@.new $@
endef
define Build/mkmylofw_16m
$(eval device_id=$(word 1,$(1)))
$(eval revision=$(word 2,$(1)))
# On WPJ344, WPJ531, and WPJ563, the default boot command tries 0x9f680000
# first and fails if the remains of the stock image are sill there
# - resulting in an infinite boot loop.
# The size parameter is grown to have that block deleted if the firmware
# isn't big enough by itself.
let \
size="$$(stat -c%s $@)" \
pad="$(subst k,* 1024,$(BLOCKSIZE))" \
pad="(pad - (size % pad)) % pad" \
newsize='size + pad' ; \
[ $$newsize -lt $$((0x660000)) ] && newsize=0x660000 ; \
$(STAGING_DIR_HOST)/bin/mkmylofw \
-B WPE72 -i 0x11f6:$(device_id):0x11f6:$(device_id) -r $(revision) \
-s 0x1000000 -p0x30000:$$newsize:al:0x80060000:"OpenWRT":$@ \
$@.new
@mv $@.new $@
endef
define Build/mkwrggimg
$(STAGING_DIR_HOST)/bin/mkwrggimg -b \
-i $@ -o $@.imghdr -d /dev/mtdblock/1 \
-m $(DEVICE_MODEL)-$(DEVICE_VARIANT) -s $(DAP_SIGNATURE) \
-v $(VERSION_DIST) -B $(REVISION)
mv $@.imghdr $@
endef
define Build/nec-enc
$(STAGING_DIR_HOST)/bin/nec-enc \
-i $@ -o $@.new -k $(1)
mv $@.new $@
endef
define Build/nec-fw
( stat -c%s $@ | tr -d "\n" | dd bs=16 count=1 conv=sync; ) >> $@
( \
echo -n -e "$(1)" | dd bs=16 count=1 conv=sync; \
echo -n "0.0.00" | dd bs=16 count=1 conv=sync; \
dd if=$@; \
) > $@.new
mv $@.new $@
endef
define Build/pisen_wmb001n-factory
-[ -f "$@" ] && \
mkdir -p "$@.tmp" && \
cp "$(KDIR)/loader-$(word 1,$(1)).uImage" "$@.tmp/uImage" && \
mv "$@" "$@.tmp/rootfs" && \
cp "bin/pisen_wmb001n_factory-header.bin" "$@" && \
$(TAR) -cp --numeric-owner --owner=0 --group=0 --mode=a-s --sort=name \
$(if $(SOURCE_DATE_EPOCH),--mtime="@$(SOURCE_DATE_EPOCH)") \
-C "$@.tmp" . | gzip -9n >> "$@" && \
rm -rf "$@.tmp"
endef
define Build/teltonika-fw-fake-checksum
# Teltonika U-Boot web based firmware upgrade/recovery routine compares
# 16 bytes from md5sum1[16] field in TP-Link v1 header (offset: 76 bytes
# from begin of the firmware file) with 16 bytes stored just before
# 0xdeadc0de marker. Values are only compared, MD5 sum is not verified.
let \
offs="$$(stat -c%s $@) - 20"; \
dd if=$@ bs=1 count=16 skip=76 |\
dd of=$@ bs=1 count=16 seek=$$offs conv=notrunc
endef
define Build/wrgg-pad-rootfs
$(STAGING_DIR_HOST)/bin/padjffs2 $(IMAGE_ROOTFS) -c 64 >>$@
endef
define Device/seama
KERNEL := kernel-bin | append-dtb | relocate-kernel | lzma
KERNEL_INITRAMFS := $$(KERNEL) | seama
IMAGES += factory.bin
SEAMA_MTDBLOCK := 1
# 64 bytes offset:
# - 28 bytes seama_header
# - 36 bytes of META data (4-bytes aligned)
IMAGE/default := append-kernel | pad-offset $$$$(BLOCKSIZE) 64 | append-rootfs
IMAGE/sysupgrade.bin := $$(IMAGE/default) | seama | pad-rootfs | \
append-metadata | check-size
IMAGE/factory.bin := $$(IMAGE/default) | pad-rootfs -x 64 | seama | \
seama-seal | check-size
SEAMA_SIGNATURE :=
endef
define Device/8dev_carambola2
SOC := ar9331
DEVICE_VENDOR := 8devices
DEVICE_MODEL := Carambola2
DEVICE_PACKAGES := kmod-usb-chipidea2
IMAGE_SIZE := 16000k
SUPPORTED_DEVICES += carambola2
endef
TARGET_DEVICES += 8dev_carambola2
define Device/8dev_lima
SOC := qca9531
DEVICE_VENDOR := 8devices
DEVICE_MODEL := Lima
DEVICE_PACKAGES := kmod-usb2
IMAGE_SIZE := 15616k
SUPPORTED_DEVICES += lima
endef
TARGET_DEVICES += 8dev_lima
define Device/adtran_bsap1880
SOC := ar7161
DEVICE_VENDOR := Adtran/Bluesocket
DEVICE_PACKAGES += -swconfig -uboot-envtools fconfig
KERNEL := kernel-bin | append-dtb | lzma | pad-to $$(BLOCKSIZE)
KERNEL_INITRAMFS := kernel-bin | append-dtb
IMAGE_SIZE := 11200k
IMAGES += kernel.bin rootfs.bin
IMAGE/kernel.bin := append-kernel
IMAGE/rootfs.bin := append-rootfs | pad-rootfs
IMAGE/sysupgrade.bin := append-rootfs | pad-rootfs | \
check-size | sysupgrade-tar rootfs=$$$$@ | append-metadata
endef
define Device/adtran_bsap1800-v2
$(Device/adtran_bsap1880)
DEVICE_MODEL := BSAP-1800
DEVICE_VARIANT := v2
endef
TARGET_DEVICES += adtran_bsap1800-v2
define Device/adtran_bsap1840
$(Device/adtran_bsap1880)
DEVICE_MODEL := BSAP-1840
endef
TARGET_DEVICES += adtran_bsap1840
define Device/airtight_c-75
SOC := qca9550
DEVICE_VENDOR := AirTight Networks
DEVICE_MODEL := C-75
DEVICE_ALT0_VENDOR := Mojo Networks
DEVICE_ALT0_MODEL := C-75
DEVICE_ALT1_VENDOR := WatchGuard
DEVICE_ALT1_MODEL := AP320
DEVICE_PACKAGES := ath10k-firmware-qca988x-ct kmod-ath10k-ct kmod-usb2
IMAGE_SIZE := 32320k
KERNEL_SIZE := 15936k
endef
TARGET_DEVICES += airtight_c-75
define Device/alfa-network_ap121f
SOC := ar9331
DEVICE_VENDOR := ALFA Network
DEVICE_MODEL := AP121F
DEVICE_PACKAGES := kmod-usb-chipidea2 kmod-usb-storage -swconfig
IMAGE_SIZE := 16064k
SUPPORTED_DEVICES += ap121f
endef
TARGET_DEVICES += alfa-network_ap121f
define Device/alfa-network_ap121fe
SOC := ar9331
DEVICE_VENDOR := ALFA Network
DEVICE_MODEL := AP121FE
DEVICE_PACKAGES := kmod-usb-chipidea2 kmod-usb-gadget-eth -swconfig
IMAGE_SIZE := 16064k
endef
TARGET_DEVICES += alfa-network_ap121fe
define Device/alfa-network_n2q
SOC := qca9531
DEVICE_VENDOR := ALFA Network
DEVICE_MODEL := N2Q
DEVICE_PACKAGES := kmod-i2c-gpio kmod-gpio-pcf857x kmod-usb2 \
kmod-usb-ledtrig-usbport rssileds
IMAGE_SIZE := 15872k
endef
TARGET_DEVICES += alfa-network_n2q
define Device/alfa-network_n5q
SOC := ar9344
DEVICE_VENDOR := ALFA Network
DEVICE_MODEL := N5Q
DEVICE_PACKAGES := rssileds
IMAGE_SIZE := 15872k
SUPPORTED_DEVICES += n5q
endef
TARGET_DEVICES += alfa-network_n5q
define Device/alfa-network_pi-wifi4
SOC := qca9531
DEVICE_VENDOR := ALFA Network
DEVICE_MODEL := Pi-WiFi4
DEVICE_PACKAGES := kmod-usb2 kmod-usb-ledtrig-usbport -swconfig
IMAGE_SIZE := 15872k
endef
TARGET_DEVICES += alfa-network_pi-wifi4
define Device/alfa-network_r36a
SOC := qca9531
DEVICE_VENDOR := ALFA Network
DEVICE_MODEL := R36A
DEVICE_PACKAGES := kmod-usb2 kmod-usb-ledtrig-usbport
IMAGE_SIZE := 15872k
SUPPORTED_DEVICES += r36a
endef
TARGET_DEVICES += alfa-network_r36a
define Device/allnet_all-wap02860ac
SOC := qca9558
DEVICE_VENDOR := ALLNET
DEVICE_MODEL := ALL-WAP02860AC
DEVICE_PACKAGES := ath10k-firmware-qca988x-ct kmod-ath10k-ct
IMAGE_SIZE := 13120k
endef
TARGET_DEVICES += allnet_all-wap02860ac
define Device/arduino_yun
SOC := ar9331
DEVICE_VENDOR := Arduino
DEVICE_MODEL := Yun
DEVICE_PACKAGES := kmod-usb-chipidea2 kmod-usb-ledtrig-usbport \
kmod-usb-storage block-mount -swconfig
IMAGE_SIZE := 15936k
SUPPORTED_DEVICES += arduino-yun
endef
TARGET_DEVICES += arduino_yun
define Device/aruba_ap-105
SOC := ar7161
DEVICE_VENDOR := Aruba
DEVICE_MODEL := AP-105
IMAGE_SIZE := 16000k
DEVICE_PACKAGES := kmod-i2c-gpio kmod-tpm-i2c-atmel
endef
TARGET_DEVICES += aruba_ap-105
define Device/avm
DEVICE_VENDOR := AVM
KERNEL := kernel-bin | append-dtb | lzma | eva-image
KERNEL_INITRAMFS := $$(KERNEL)
IMAGE/sysupgrade.bin := append-kernel | pad-to 64k | \
append-squashfs-fakeroot-be | pad-to 256 | append-rootfs | pad-rootfs | \
append-metadata | check-size
DEVICE_PACKAGES := fritz-tffs
endef
define Device/avm_fritz1750e
$(Device/avm)
SOC := qca9556
IMAGE_SIZE := 15232k
DEVICE_MODEL := FRITZ!WLAN Repeater 1750E
DEVICE_PACKAGES += rssileds kmod-ath10k-ct-smallbuffers \
ath10k-firmware-qca988x-ct -swconfig
endef
TARGET_DEVICES += avm_fritz1750e
define Device/avm_fritz300e
$(Device/avm)
SOC := ar7242
IMAGE_SIZE := 15232k
DEVICE_MODEL := FRITZ!WLAN Repeater 300E
DEVICE_PACKAGES += rssileds -swconfig
SUPPORTED_DEVICES += fritz300e
endef
TARGET_DEVICES += avm_fritz300e
define Device/avm_fritz4020
$(Device/avm)
SOC := qca9561
IMAGE_SIZE := 15232k
DEVICE_MODEL := FRITZ!Box 4020
SUPPORTED_DEVICES += fritz4020
endef
TARGET_DEVICES += avm_fritz4020
define Device/avm_fritz450e
$(Device/avm)
SOC := qca9556
IMAGE_SIZE := 15232k
DEVICE_MODEL := FRITZ!WLAN Repeater 450E
SUPPORTED_DEVICES += fritz450e
endef
TARGET_DEVICES += avm_fritz450e
define Device/avm_fritzdvbc
$(Device/avm)
SOC := qca9556
IMAGE_SIZE := 15232k
DEVICE_MODEL := FRITZ!WLAN Repeater DVB-C
DEVICE_PACKAGES += rssileds kmod-ath10k-ct-smallbuffers \
ath10k-firmware-qca988x-ct -swconfig
endef
TARGET_DEVICES += avm_fritzdvbc
define Device/belkin_f9x-v2
SOC := qca9558
DEVICE_VENDOR := Belkin
IMAGE_SIZE := 14464k
DEVICE_PACKAGES += kmod-ath10k-ct ath10k-firmware-qca988x-ct kmod-usb2 \
kmod-usb3 kmod-usb-ledtrig-usbport
LOADER_TYPE := bin
LOADER_FLASH_OFFS := 0x50000
COMPILE := loader-$(1).bin loader-$(1).uImage
COMPILE/loader-$(1).bin := loader-okli-compile
COMPILE/loader-$(1).uImage := append-loader-okli $(1) | pad-to 64k | \
lzma | uImage lzma
KERNEL := kernel-bin | append-dtb | lzma | uImage lzma -M 0x4f4b4c49
IMAGES += factory.bin
IMAGE/factory.bin := append-kernel | pad-to $$$$(BLOCKSIZE) | \
append-rootfs | pad-rootfs | check-size | \
edimax-headers $$$$(EDIMAX_HEADER_MAGIC) $$$$(EDIMAX_HEADER_MODEL) | \
pad-to $$$$(BLOCKSIZE)
endef
define Device/belkin_f9j1108-v2
$(Device/belkin_f9x-v2)
DEVICE_MODEL := F9J1108 v2 (AC1750 DB Wi-Fi)
EDIMAX_HEADER_MAGIC := F9J1108v1
EDIMAX_HEADER_MODEL := BR-6679BAC
endef
TARGET_DEVICES += belkin_f9j1108-v2
define Device/belkin_f9k1115-v2
$(Device/belkin_f9x-v2)
DEVICE_MODEL := F9K1115 v2 (AC1750 DB Wi-Fi)
EDIMAX_HEADER_MAGIC := eDiMaX
EDIMAX_HEADER_MODEL := F9K1115V2
endef
TARGET_DEVICES += belkin_f9k1115-v2
define Device/buffalo_bhr-4grv
$(Device/buffalo_common)
SOC := ar7242
DEVICE_MODEL := BHR-4GRV
BUFFALO_PRODUCT := BHR-4GRV
DEVICE_PACKAGES := kmod-usb2 kmod-usb-ledtrig-usbport
IMAGE_SIZE := 32256k
SUPPORTED_DEVICES += wzr-hp-g450h
endef
TARGET_DEVICES += buffalo_bhr-4grv
define Device/buffalo_bhr-4grv2
SOC := qca9557
DEVICE_VENDOR := Buffalo
DEVICE_MODEL := BHR-4GRV2
IMAGE_SIZE := 16000k
endef
TARGET_DEVICES += buffalo_bhr-4grv2
define Device/buffalo_wzr_ar7161
$(Device/buffalo_common)
SOC := ar7161
BUFFALO_PRODUCT := WZR-HP-AG300H
DEVICE_PACKAGES := kmod-usb-ohci kmod-usb2 kmod-usb-ledtrig-usbport \
kmod-leds-reset kmod-owl-loader
IMAGE_SIZE := 32320k
SUPPORTED_DEVICES += wzr-hp-ag300h
endef
define Device/buffalo_wzr-600dhp
$(Device/buffalo_wzr_ar7161)
DEVICE_MODEL := WZR-600DHP
endef
TARGET_DEVICES += buffalo_wzr-600dhp
define Device/buffalo_wzr-hp-ag300h
$(Device/buffalo_wzr_ar7161)
DEVICE_MODEL := WZR-HP-AG300H
endef
TARGET_DEVICES += buffalo_wzr-hp-ag300h
define Device/buffalo_wzr-hp-g302h-a1a0
$(Device/buffalo_common)
SOC := ar7242
DEVICE_MODEL := WZR-HP-G302H
DEVICE_VARIANT := A1A0
BUFFALO_PRODUCT := WZR-HP-G302H
BUFFALO_HWVER := 4
DEVICE_PACKAGES := kmod-usb2 kmod-usb-ledtrig-usbport
IMAGE_SIZE := 32128k
SUPPORTED_DEVICES += wzr-hp-g300nh2
endef
TARGET_DEVICES += buffalo_wzr-hp-g302h-a1a0
define Device/buffalo_wzr-hp-g450h
$(Device/buffalo_common)
SOC := ar7242
DEVICE_MODEL := WZR-HP-G450H/WZR-450HP
BUFFALO_PRODUCT := WZR-HP-G450H
DEVICE_PACKAGES := kmod-usb2 kmod-usb-ledtrig-usbport
IMAGE_SIZE := 32256k
SUPPORTED_DEVICES += wzr-hp-g450h
endef
TARGET_DEVICES += buffalo_wzr-hp-g450h
define Device/comfast_cf-e110n-v2
SOC := qca9533
DEVICE_VENDOR := COMFAST
DEVICE_MODEL := CF-E110N
DEVICE_VARIANT := v2
DEVICE_PACKAGES := rssileds -swconfig -uboot-envtools
IMAGE_SIZE := 16192k
endef
TARGET_DEVICES += comfast_cf-e110n-v2
define Device/comfast_cf-e120a-v3
SOC := ar9344
DEVICE_VENDOR := COMFAST
DEVICE_MODEL := CF-E120A
DEVICE_VARIANT := v3
DEVICE_PACKAGES := rssileds -uboot-envtools
IMAGE_SIZE := 8000k
endef
TARGET_DEVICES += comfast_cf-e120a-v3
define Device/comfast_cf-e130n-v2
SOC := qca9531
DEVICE_VENDOR := COMFAST
DEVICE_MODEL := CF-E130N
DEVICE_VARIANT := v2
DEVICE_PACKAGES := rssileds -swconfig -uboot-envtools
IMAGE_SIZE := 7936k
endef
TARGET_DEVICES += comfast_cf-e130n-v2
define Device/comfast_cf-e313ac
SOC := qca9531
DEVICE_VENDOR := COMFAST
DEVICE_MODEL := CF-E313AC
DEVICE_PACKAGES := rssileds kmod-ath10k-ct-smallbuffers \
ath10k-firmware-qca9888-ct -swconfig -uboot-envtools
IMAGE_SIZE := 7936k
endef
TARGET_DEVICES += comfast_cf-e313ac
define Device/comfast_cf-e314n-v2
SOC := qca9531
DEVICE_VENDOR := COMFAST
DEVICE_MODEL := CF-E314N
DEVICE_VARIANT := v2
DEVICE_PACKAGES := rssileds
IMAGE_SIZE := 7936k
endef
TARGET_DEVICES += comfast_cf-e314n-v2
define Device/comfast_cf-e5
SOC := qca9531
DEVICE_VENDOR := COMFAST
DEVICE_MODEL := CF-E5/E7
DEVICE_PACKAGES := rssileds kmod-usb2 kmod-usb-net-qmi-wwan -swconfig \
-uboot-envtools
IMAGE_SIZE := 16192k
endef
TARGET_DEVICES += comfast_cf-e5
define Device/comfast_cf-e560ac
SOC := qca9531
DEVICE_VENDOR := COMFAST
DEVICE_MODEL := CF-E560AC
DEVICE_PACKAGES := kmod-usb2 kmod-ath10k-ct ath10k-firmware-qca9888-ct
IMAGE_SIZE := 16128k
endef
TARGET_DEVICES += comfast_cf-e560ac
define Device/comfast_cf-ew72
SOC := qca9531
DEVICE_VENDOR := COMFAST
DEVICE_MODEL := CF-EW72
DEVICE_PACKAGES := kmod-usb2 kmod-ath10k-ct ath10k-firmware-qca9888-ct \
-uboot-envtools -swconfig
IMAGE_SIZE := 16192k
endef
TARGET_DEVICES += comfast_cf-ew72
define Device/comfast_cf-wr650ac-v1
SOC := qca9558
DEVICE_VENDOR := COMFAST
DEVICE_MODEL := CF-WR650AC
DEVICE_VARIANT := v1
DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca988x-ct
IMAGE_SIZE := 16128k
endef
TARGET_DEVICES += comfast_cf-wr650ac-v1
define Device/comfast_cf-wr650ac-v2
SOC := qca9558
DEVICE_VENDOR := COMFAST
DEVICE_MODEL := CF-WR650AC
DEVICE_VARIANT := v2
DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca988x-ct
IMAGE_SIZE := 16000k
endef
TARGET_DEVICES += comfast_cf-wr650ac-v2
define Device/comfast_cf-wr752ac-v1
SOC := qca9531
DEVICE_VENDOR := COMFAST
DEVICE_MODEL := CF-WR752AC
DEVICE_VARIANT := v1
DEVICE_PACKAGES := kmod-usb2 kmod-ath10k-ct ath10k-firmware-qca9888-ct \
-uboot-envtools
IMAGE_SIZE := 16192k
endef
TARGET_DEVICES += comfast_cf-wr752ac-v1
define Device/compex_wpj344-16m
SOC := ar9344
DEVICE_PACKAGES := kmod-usb2
IMAGE_SIZE := 16128k
DEVICE_VENDOR := Compex
DEVICE_MODEL := WPJ344
DEVICE_VARIANT := 16M
SUPPORTED_DEVICES += wpj344
IMAGES += cpximg-6a08.bin
IMAGE/cpximg-6a08.bin := append-kernel | pad-to $$$$(BLOCKSIZE) | append-rootfs | pad-rootfs | mkmylofw_16m 0x690 3
endef
TARGET_DEVICES += compex_wpj344-16m
define Device/compex_wpj531-16m
SOC := qca9531
DEVICE_PACKAGES := kmod-usb2
IMAGE_SIZE := 16128k
DEVICE_VENDOR := Compex
DEVICE_MODEL := WPJ531
DEVICE_VARIANT := 16M
SUPPORTED_DEVICES += wpj531
IMAGES += cpximg-7a03.bin cpximg-7a04.bin cpximg-7a06.bin cpximg-7a07.bin
IMAGE/cpximg-7a03.bin := append-kernel | pad-to $$$$(BLOCKSIZE) | append-rootfs | pad-rootfs | mkmylofw_16m 0x68a 2
IMAGE/cpximg-7a04.bin := append-kernel | pad-to $$$$(BLOCKSIZE) | append-rootfs | pad-rootfs | mkmylofw_16m 0x693 3
IMAGE/cpximg-7a06.bin := append-kernel | pad-to $$$$(BLOCKSIZE) | append-rootfs | pad-rootfs | mkmylofw_16m 0x693 3
IMAGE/cpximg-7a07.bin := append-kernel | pad-to $$$$(BLOCKSIZE) | append-rootfs | pad-rootfs | mkmylofw_16m 0x693 3
endef
TARGET_DEVICES += compex_wpj531-16m
define Device/compex_wpj563
SOC := qca9563
DEVICE_PACKAGES := kmod-usb2 kmod-usb3
IMAGE_SIZE := 16128k
DEVICE_VENDOR := Compex
DEVICE_MODEL := WPJ563
SUPPORTED_DEVICES += wpj563
IMAGES += cpximg-7a02.bin
IMAGE/cpximg-7a02.bin := append-kernel | pad-to $$$$(BLOCKSIZE) | append-rootfs | pad-rootfs | mkmylofw_16m 0x694 2
endef
TARGET_DEVICES += compex_wpj563
define Device/devolo_dvl1200e
SOC := qca9558
DEVICE_VENDOR := devolo
DEVICE_MODEL := WiFi pro 1200e
DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca988x-ct
IMAGE_SIZE := 15936k
endef
TARGET_DEVICES += devolo_dvl1200e
define Device/devolo_dvl1200i
SOC := qca9558
DEVICE_VENDOR := devolo
DEVICE_MODEL := WiFi pro 1200i
DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca988x-ct
IMAGE_SIZE := 15936k
endef
TARGET_DEVICES += devolo_dvl1200i
define Device/devolo_dvl1750c
SOC := qca9558
DEVICE_VENDOR := devolo
DEVICE_MODEL := WiFi pro 1750c
DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca988x-ct
IMAGE_SIZE := 15936k
endef
TARGET_DEVICES += devolo_dvl1750c
define Device/devolo_dvl1750e
SOC := qca9558
DEVICE_VENDOR := devolo
DEVICE_MODEL := WiFi pro 1750e
DEVICE_PACKAGES := kmod-usb2 kmod-ath10k-ct ath10k-firmware-qca988x-ct
IMAGE_SIZE := 15936k
endef
TARGET_DEVICES += devolo_dvl1750e
define Device/devolo_dvl1750i
SOC := qca9558
DEVICE_VENDOR := devolo
DEVICE_MODEL := WiFi pro 1750i
DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca988x-ct
IMAGE_SIZE := 15936k
endef
TARGET_DEVICES += devolo_dvl1750i
define Device/devolo_dvl1750x
SOC := qca9558
DEVICE_VENDOR := devolo
DEVICE_MODEL := WiFi pro 1750x
DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca988x-ct
IMAGE_SIZE := 15936k
endef
TARGET_DEVICES += devolo_dvl1750x
define Device/devolo_magic-2-wifi
SOC := ar9344
DEVICE_VENDOR := Devolo
DEVICE_MODEL := Magic 2 WiFi
DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca988x-ct
IMAGE_SIZE := 15872k
endef
TARGET_DEVICES += devolo_magic-2-wifi
define Device/dlink_dap-13xx
SOC := qca9533
DEVICE_VENDOR := D-Link
DEVICE_PACKAGES += rssileds
IMAGE_SIZE := 7936k
IMAGES += factory.bin
IMAGE/factory.bin := append-kernel | pad-to $$$$(BLOCKSIZE) | \
append-rootfs | pad-rootfs | check-size | mkdapimg2 0xE0000
endef
define Device/dlink_dap-1330-a1
$(Device/dlink_dap-13xx)
DEVICE_MODEL := DAP-1330
DEVICE_VARIANT := A1
DAP_SIGNATURE := HONEYBEE-FIRMWARE-DAP-1330
SUPPORTED_DEVICES += dap-1330-a1
endef
TARGET_DEVICES += dlink_dap-1330-a1
define Device/dlink_dap-1365-a1
$(Device/dlink_dap-13xx)
DEVICE_MODEL := DAP-1365
DEVICE_VARIANT := A1
DAP_SIGNATURE := HONEYBEE-FIRMWARE-DAP-1365
endef
TARGET_DEVICES += dlink_dap-1365-a1
define Device/dlink_dap-2xxx
IMAGES += factory.img
IMAGE/factory.img := append-kernel | pad-offset 6144k 160 | \
append-rootfs | wrgg-pad-rootfs | mkwrggimg | check-size
IMAGE/sysupgrade.bin := append-kernel | mkwrggimg | \
pad-to $$$$(BLOCKSIZE) | append-rootfs | append-metadata | check-size
KERNEL := kernel-bin | append-dtb | relocate-kernel | lzma
KERNEL_INITRAMFS := $$(KERNEL) | mkwrggimg
endef
define Device/dlink_dap-2230-a1
$(Device/dlink_dap-2xxx)
SOC := qca9533
DEVICE_VENDOR := D-Link
DEVICE_MODEL := DAP-2230
DEVICE_VARIANT := A1
IMAGE_SIZE := 15232k
DAP_SIGNATURE := wapn31_dkbs_dap2230
endef
TARGET_DEVICES += dlink_dap-2230-a1
define Device/dlink_dap-2660-a1
$(Device/dlink_dap-2xxx)
SOC := qca9557
DEVICE_VENDOR := D-Link
DEVICE_MODEL := DAP-2660
DEVICE_VARIANT := A1
DEVICE_PACKAGES := ath10k-firmware-qca988x-ct kmod-ath10k-ct
IMAGE_SIZE := 15232k
DAP_SIGNATURE := wapac09_dkbs_dap2660
endef
TARGET_DEVICES += dlink_dap-2660-a1
define Device/dlink_dap-2680-a1
$(Device/dlink_dap-2xxx)
SOC := qca9558
DEVICE_VENDOR := D-Link
DEVICE_MODEL := DAP-2680
DEVICE_VARIANT := A1
DEVICE_PACKAGES := ath10k-firmware-qca99x0-ct kmod-ath10k-ct
IMAGE_SIZE := 15232k
DAP_SIGNATURE := wapac36_dkbs_dap2680
endef
TARGET_DEVICES += dlink_dap-2680-a1
define Device/dlink_dap-2695-a1
SOC := qca9558
DEVICE_PACKAGES := ath10k-firmware-qca988x-ct kmod-ath10k-ct
DEVICE_VENDOR := D-Link
DEVICE_MODEL := DAP-2965
DEVICE_VARIANT := A1
IMAGES := factory.img sysupgrade.bin
IMAGE_SIZE := 15360k
IMAGE/default := append-kernel | pad-offset 65536 160
IMAGE/factory.img := $$(IMAGE/default) | append-rootfs | wrgg-pad-rootfs | \
mkwrggimg | check-size
IMAGE/sysupgrade.bin := $$(IMAGE/default) | mkwrggimg | append-rootfs | \
wrgg-pad-rootfs | append-metadata | check-size
KERNEL := kernel-bin | append-dtb | relocate-kernel | lzma
KERNEL_INITRAMFS := $$(KERNEL) | mkwrggimg
DAP_SIGNATURE := wapac02_dkbs_dap2695
SUPPORTED_DEVICES += dap-2695-a1
endef
TARGET_DEVICES += dlink_dap-2695-a1
define Device/dlink_dap-3320-a1
$(Device/dlink_dap-2xxx)
SOC := qca9533
DEVICE_VENDOR := D-Link
DEVICE_MODEL := DAP-3320
DEVICE_VARIANT := A1
IMAGE_SIZE := 15296k
DAP_SIGNATURE := wapn29_dkbs_dap3320
endef
TARGET_DEVICES += dlink_dap-3320-a1
define Device/dlink_dch-g020-a1
SOC := qca9531
DEVICE_VENDOR := D-Link
DEVICE_MODEL := DCH-G020
DEVICE_VARIANT := A1
DEVICE_PACKAGES := kmod-gpio-pca953x kmod-i2c-gpio kmod-usb2 kmod-usb-acm
IMAGES += factory.bin
IMAGE_SIZE := 14784k
IMAGE/factory.bin := append-kernel | pad-to $$$$(BLOCKSIZE) | \
append-rootfs | pad-rootfs | check-size | mkdapimg2 0x20000
DAP_SIGNATURE := HONEYBEE-FIRMWARE-DCH-G020
endef
TARGET_DEVICES += dlink_dch-g020-a1
define Device/dlink_dir-505
SOC := ar9330
DEVICE_VENDOR := D-Link
DEVICE_MODEL := DIR-505
IMAGE_SIZE := 7680k
DEVICE_PACKAGES := kmod-usb2
SUPPORTED_DEVICES += dir-505-a1
endef
TARGET_DEVICES += dlink_dir-505
define Device/dlink_dir-825-b1
SOC := ar7161
DEVICE_VENDOR := D-Link
DEVICE_MODEL := DIR-825
DEVICE_VARIANT := B1
IMAGE_SIZE := 6208k
IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | \
append-metadata | check-size
DEVICE_PACKAGES := kmod-usb-ohci kmod-usb2 kmod-usb-ledtrig-usbport \
kmod-leds-reset kmod-owl-loader
SUPPORTED_DEVICES += dir-825-b1
endef
TARGET_DEVICES += dlink_dir-825-b1
define Device/dlink_dir-825-c1
SOC := ar9344
DEVICE_VENDOR := D-Link
DEVICE_MODEL := DIR-825
DEVICE_VARIANT := C1
DEVICE_PACKAGES := kmod-usb2 kmod-usb-ledtrig-usbport kmod-leds-reset \
kmod-owl-loader
SUPPORTED_DEVICES += dir-825-c1
IMAGE_SIZE := 15936k
IMAGES := factory.bin sysupgrade.bin
IMAGE/default := append-kernel | pad-to $$$$(BLOCKSIZE) | append-rootfs | \
pad-rootfs
IMAGE/factory.bin := $$(IMAGE/default) | pad-offset $$$$(IMAGE_SIZE) 26 | \
append-string 00DB120AR9344-RT-101214-00 | check-size
IMAGE/sysupgrade.bin := $$(IMAGE/default) | append-metadata | \
check-size
endef
TARGET_DEVICES += dlink_dir-825-c1
define Device/dlink_dir-835-a1
SOC := ar9344
DEVICE_VENDOR := D-Link
DEVICE_MODEL := DIR-835
DEVICE_VARIANT := A1
DEVICE_PACKAGES := kmod-usb2 kmod-leds-reset kmod-owl-loader
SUPPORTED_DEVICES += dir-835-a1
IMAGE_SIZE := 15936k
IMAGES := factory.bin sysupgrade.bin
IMAGE/default := append-kernel | pad-to $$$$(BLOCKSIZE) | append-rootfs | \
pad-rootfs
IMAGE/factory.bin := $$(IMAGE/default) | pad-offset $$$$(IMAGE_SIZE) 26 | \
append-string 00DB120AR9344-RT-101214-00 | check-size
IMAGE/sysupgrade.bin := $$(IMAGE/default) | append-metadata | \
check-size
endef
TARGET_DEVICES += dlink_dir-835-a1
define Device/dlink_dir-842-c
SOC := qca9563
DEVICE_VENDOR := D-Link
DEVICE_MODEL := DIR-842
KERNEL := kernel-bin | append-dtb | relocate-kernel | lzma
KERNEL_INITRAMFS := $$(KERNEL) | seama
IMAGES += factory.bin
SEAMA_MTDBLOCK := 5
SEAMA_SIGNATURE := wrgac65_dlink.2015_dir842
# 64 bytes offset:
# - 28 bytes seama_header
# - 36 bytes of META data (4-bytes aligned)
IMAGE/default := append-kernel | uImage lzma | \
pad-offset $$$$(BLOCKSIZE) 64 | append-rootfs
IMAGE/sysupgrade.bin := $$(IMAGE/default) | seama | pad-rootfs | \
append-metadata | check-size
IMAGE/factory.bin := $$(IMAGE/default) | pad-rootfs -x 64 | seama | \
seama-seal | check-size
IMAGE_SIZE := 15680k
endef
define Device/dlink_dir-842-c1
$(Device/dlink_dir-842-c)
DEVICE_VARIANT := C1
DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca9888-ct
endef
TARGET_DEVICES += dlink_dir-842-c1
define Device/dlink_dir-842-c2
$(Device/dlink_dir-842-c)
DEVICE_VARIANT := C2
DEVICE_PACKAGES := kmod-usb2 kmod-ath10k-ct ath10k-firmware-qca9888-ct
endef
TARGET_DEVICES += dlink_dir-842-c2
define Device/dlink_dir-842-c3
$(Device/dlink_dir-842-c)
DEVICE_VARIANT := C3
DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca9888-ct
endef
TARGET_DEVICES += dlink_dir-842-c3
define Device/dlink_dir-859-a1
$(Device/seama)
SOC := qca9563
DEVICE_VENDOR := D-Link
DEVICE_MODEL := DIR-859
DEVICE_VARIANT := A1
IMAGE_SIZE := 15872k
DEVICE_PACKAGES := kmod-usb2 kmod-ath10k-ct-smallbuffers ath10k-firmware-qca988x-ct
SEAMA_SIGNATURE := wrgac37_dlink.2013gui_dir859
endef
TARGET_DEVICES += dlink_dir-859-a1
define Device/elecom_wrc-1750ghbk2-i
SOC := qca9563
DEVICE_VENDOR := ELECOM
DEVICE_MODEL := WRC-1750GHBK2-I/C
IMAGE_SIZE := 15808k
KERNEL_INITRAMFS := $$(KERNEL) | pad-to 2 | \
add-elecom-factory-initramfs RN68 WRC-1750GHBK2
DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca988x-ct
endef
TARGET_DEVICES += elecom_wrc-1750ghbk2-i
define Device/elecom_wrc-300ghbk2-i
SOC := qca9563
DEVICE_VENDOR := ELECOM
DEVICE_MODEL := WRC-300GHBK2-I
IMAGE_SIZE := 7616k
KERNEL_INITRAMFS := $$(KERNEL) | pad-to 2 | \
add-elecom-factory-initramfs RN51 WRC-300GHBK2-I
endef
TARGET_DEVICES += elecom_wrc-300ghbk2-i
define Device/embeddedwireless_dorin
SOC := ar9331
DEVICE_VENDOR := Embedded Wireless
DEVICE_MODEL := Dorin
DEVICE_PACKAGES := kmod-usb-chipidea2
IMAGE_SIZE := 16000k
endef
TARGET_DEVICES += embeddedwireless_dorin
define Device/engenius_eap300-v2
$(Device/engenius_loader_okli)
SOC := ar9341
DEVICE_MODEL := EAP300
DEVICE_VARIANT := v2
IMAGE_SIZE := 12032k
LOADER_FLASH_OFFS := 0x230000
ENGENIUS_IMGNAME := senao-eap300v2
endef
TARGET_DEVICES += engenius_eap300-v2
define Device/engenius_eap600
$(Device/engenius_loader_okli)
SOC := ar9344
DEVICE_MODEL := EAP600
IMAGE_SIZE := 12032k
LOADER_FLASH_OFFS := 0x230000
ENGENIUS_IMGNAME := senao-eap600
endef
TARGET_DEVICES += engenius_eap600
define Device/engenius_ecb1200
SOC := qca9557
DEVICE_VENDOR := EnGenius
DEVICE_MODEL := ECB1200
DEVICE_PACKAGES := ath10k-firmware-qca988x-ct kmod-ath10k-ct
IMAGE_SIZE := 15680k
IMAGES += factory.bin
IMAGE/factory.bin := append-kernel | pad-to $$$$(BLOCKSIZE) | \
append-rootfs | pad-rootfs | check-size | \
senao-header -r 0x101 -p 0x6e -t 2
endef
TARGET_DEVICES += engenius_ecb1200
define Device/engenius_ecb1750
SOC := qca9558
DEVICE_VENDOR := EnGenius
DEVICE_MODEL := ECB1750
DEVICE_PACKAGES := ath10k-firmware-qca988x-ct kmod-ath10k-ct
IMAGE_SIZE := 15680k
IMAGES += factory.bin
IMAGE/factory.bin := append-kernel | pad-to $$$$(BLOCKSIZE) | \
append-rootfs | pad-rootfs | check-size | \
senao-header -r 0x101 -p 0x6d -t 2
endef
TARGET_DEVICES += engenius_ecb1750
define Device/engenius_ecb600
$(Device/engenius_loader_okli)
SOC := ar9344
DEVICE_MODEL := ECB600
IMAGE_SIZE := 12032k
LOADER_FLASH_OFFS := 0x230000
ENGENIUS_IMGNAME := senao-ecb600
endef
TARGET_DEVICES += engenius_ecb600
define Device/engenius_ens202ext-v1
$(Device/engenius_loader_okli)
SOC := ar9341
DEVICE_MODEL := ENS202EXT
DEVICE_VARIANT := v1
DEVICE_PACKAGES := rssileds
IMAGE_SIZE := 12032k
LOADER_FLASH_OFFS := 0x230000
ENGENIUS_IMGNAME := senao-ens202ext
endef
TARGET_DEVICES += engenius_ens202ext-v1
define Device/engenius_enstationac-v1
$(Device/engenius_loader_okli)
SOC := qca9557
DEVICE_MODEL := EnStationAC
DEVICE_VARIANT := v1
DEVICE_PACKAGES := ath10k-firmware-qca988x-ct kmod-ath10k-ct rssileds
IMAGE_SIZE := 11520k
LOADER_FLASH_OFFS := 0x230000
ENGENIUS_IMGNAME := ar71xx-generic-enstationac
endef
TARGET_DEVICES += engenius_enstationac-v1
define Device/engenius_epg5000
SOC := qca9558
DEVICE_VENDOR := EnGenius
DEVICE_MODEL := EPG5000
DEVICE_PACKAGES := ath10k-firmware-qca988x-ct kmod-ath10k-ct kmod-usb2
IMAGE_SIZE := 14656k
IMAGES += factory.dlf
IMAGE/factory.dlf := append-kernel | pad-to $$$$(BLOCKSIZE) | \
append-rootfs | pad-rootfs | check-size | \
senao-header -r 0x101 -p 0x71 -t 2
SUPPORTED_DEVICES += epg5000
endef
TARGET_DEVICES += engenius_epg5000
define Device/engenius_ews511ap
SOC := qca9531
DEVICE_VENDOR := EnGenius
DEVICE_MODEL := EWS511AP
DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca9887-ct
IMAGE_SIZE := 16000k
endef
TARGET_DEVICES += engenius_ews511ap
define Device/enterasys_ws-ap3705i
SOC := ar9344
DEVICE_VENDOR := Enterasys
DEVICE_MODEL := WS-AP3705i
IMAGE_SIZE := 30528k
endef
TARGET_DEVICES += enterasys_ws-ap3705i
define Device/etactica_eg200
SOC := ar9331
DEVICE_VENDOR := eTactica
DEVICE_MODEL := EG200
DEVICE_PACKAGES := kmod-usb-chipidea2 kmod-ledtrig-oneshot \
kmod-usb-serial kmod-usb-serial-ftdi kmod-usb-storage kmod-fs-ext4
IMAGE_SIZE := 16000k
SUPPORTED_DEVICES += rme-eg200
endef
TARGET_DEVICES += etactica_eg200
define Device/glinet_6408
$(Device/tplink-8mlzma)
SOC := ar9331
DEVICE_VENDOR := GL.iNet
DEVICE_MODEL := 6408
DEVICE_PACKAGES := kmod-usb2
IMAGE_SIZE := 8000k
TPLINK_HWID := 0x08000001
IMAGES := sysupgrade.bin
SUPPORTED_DEVICES += gl-inet
endef
TARGET_DEVICES += glinet_6408
define Device/glinet_6416
$(Device/tplink-16mlzma)
SOC := ar9331
DEVICE_VENDOR := GL.iNet
DEVICE_MODEL := 6416
DEVICE_PACKAGES := kmod-usb2
IMAGE_SIZE := 16192k
TPLINK_HWID := 0x08000001
IMAGES := sysupgrade.bin
SUPPORTED_DEVICES += gl-inet
endef
TARGET_DEVICES += glinet_6416
define Device/glinet_gl-ar150
SOC := ar9330
DEVICE_VENDOR := GL.iNet
DEVICE_MODEL := GL-AR150
DEVICE_PACKAGES := kmod-usb-chipidea2
IMAGE_SIZE := 16000k
SUPPORTED_DEVICES += gl-ar150
endef
TARGET_DEVICES += glinet_gl-ar150
define Device/glinet_gl-ar300m-common-nor
SOC := qca9531
DEVICE_VENDOR := GL.iNet
DEVICE_PACKAGES := kmod-usb2
IMAGE_SIZE := 16000k
SUPPORTED_DEVICES += gl-ar300m
endef
define Device/glinet_gl-ar300m-lite
$(Device/glinet_gl-ar300m-common-nor)
DEVICE_MODEL := GL-AR300M
DEVICE_VARIANT := Lite
endef
TARGET_DEVICES += glinet_gl-ar300m-lite
define Device/glinet_gl-ar300m16
$(Device/glinet_gl-ar300m-common-nor)
DEVICE_MODEL := GL-AR300M16
endef
TARGET_DEVICES += glinet_gl-ar300m16
define Device/glinet_gl-ar750
SOC := qca9531
DEVICE_VENDOR := GL.iNet
DEVICE_MODEL := GL-AR750
DEVICE_PACKAGES := kmod-usb2 kmod-ath10k-ct ath10k-firmware-qca9887-ct
IMAGE_SIZE := 16000k
SUPPORTED_DEVICES += gl-ar750
endef
TARGET_DEVICES += glinet_gl-ar750
define Device/glinet_gl-mifi
SOC := ar9331
DEVICE_VENDOR := GL.iNET
DEVICE_MODEL := GL-MiFi
DEVICE_PACKAGES := kmod-usb-chipidea2
IMAGE_SIZE := 16000k
SUPPORTED_DEVICES += gl-mifi
endef
TARGET_DEVICES += glinet_gl-mifi
define Device/glinet_gl-usb150
SOC := ar9331
DEVICE_VENDOR := GL.iNET
DEVICE_MODEL := GL-USB150
IMAGE_SIZE := 16000k
SUPPORTED_DEVICES += gl-usb150
endef
TARGET_DEVICES += glinet_gl-usb150
define Device/glinet_gl-x750
SOC := qca9531
DEVICE_VENDOR := GL.iNet
DEVICE_MODEL := GL-X750
DEVICE_PACKAGES := kmod-usb2 kmod-ath10k-ct ath10k-firmware-qca9887-ct
IMAGE_SIZE := 16000k
endef
TARGET_DEVICES += glinet_gl-x750
define Device/hak5_lan-turtle
$(Device/tplink-16mlzma)
SOC := ar9331
DEVICE_VENDOR := Hak5
DEVICE_MODEL := LAN Turtle
TPLINK_HWID := 0x5348334c
IMAGES := sysupgrade.bin
DEVICE_PACKAGES := kmod-usb-chipidea2 -iwinfo -kmod-ath9k -swconfig \
-uboot-envtools -wpad-basic-wolfssl
SUPPORTED_DEVICES += lan-turtle
endef
TARGET_DEVICES += hak5_lan-turtle
define Device/hak5_packet-squirrel
$(Device/tplink-16mlzma)
SOC := ar9331
DEVICE_VENDOR := Hak5
DEVICE_MODEL := Packet Squirrel
TPLINK_HWID := 0x5351524c
IMAGES := sysupgrade.bin
DEVICE_PACKAGES := kmod-usb-chipidea2 -iwinfo -kmod-ath9k -swconfig \
-uboot-envtools -wpad-basic-wolfssl
SUPPORTED_DEVICES += packet-squirrel
endef
TARGET_DEVICES += hak5_packet-squirrel
define Device/hak5_wifi-pineapple-nano
$(Device/tplink-16mlzma)
SOC := ar9331
DEVICE_VENDOR := Hak5
DEVICE_MODEL := WiFi Pineapple NANO
TPLINK_HWID := 0x4e414e4f
IMAGES := sysupgrade.bin
DEVICE_PACKAGES := kmod-ath9k-htc kmod-usb-chipidea2 kmod-usb-storage \
-swconfig -uboot-envtools
SUPPORTED_DEVICES += wifi-pineapple-nano
endef
TARGET_DEVICES += hak5_wifi-pineapple-nano
define Device/iodata_etg3-r
SOC := ar9342
DEVICE_VENDOR := I-O DATA
DEVICE_MODEL := ETG3-R
IMAGE_SIZE := 7680k
DEVICE_PACKAGES := -iwinfo -kmod-ath9k -wpad-basic-wolfssl
endef
TARGET_DEVICES += iodata_etg3-r
define Device/iodata_wn-ac1167dgr
SOC := qca9557
DEVICE_VENDOR := I-O DATA
DEVICE_MODEL := WN-AC1167DGR
IMAGE_SIZE := 14656k
IMAGES += factory.bin
IMAGE/factory.bin := append-kernel | pad-to $$$$(BLOCKSIZE) | \
append-rootfs | pad-rootfs | check-size | \
senao-header -r 0x30a -p 0x61 -t 2
DEVICE_PACKAGES := kmod-usb2 kmod-ath10k-ct ath10k-firmware-qca988x-ct
endef
TARGET_DEVICES += iodata_wn-ac1167dgr
define Device/iodata_wn-ac1600dgr
SOC := qca9557
DEVICE_VENDOR := I-O DATA
DEVICE_MODEL := WN-AC1600DGR
IMAGE_SIZE := 14656k
IMAGES += factory.bin
IMAGE/factory.bin := append-kernel | pad-to $$$$(BLOCKSIZE) | \
append-rootfs | pad-rootfs | check-size | \
senao-header -r 0x30a -p 0x60 -t 2 -v 200
DEVICE_PACKAGES := kmod-usb2 kmod-ath10k-ct ath10k-firmware-qca988x-ct
endef
TARGET_DEVICES += iodata_wn-ac1600dgr
define Device/iodata_wn-ac1600dgr2
SOC := qca9557
DEVICE_VENDOR := I-O DATA
DEVICE_MODEL := WN-AC1600DGR2/DGR3
IMAGE_SIZE := 14656k
IMAGES += dgr2-dgr3-factory.bin
IMAGE/dgr2-dgr3-factory.bin := append-kernel | pad-to $$$$(BLOCKSIZE) | \
append-rootfs | pad-rootfs | check-size | \
senao-header -r 0x30a -p 0x60 -t 2 -v 200
DEVICE_PACKAGES := kmod-usb2 kmod-ath10k-ct ath10k-firmware-qca988x-ct
endef
TARGET_DEVICES += iodata_wn-ac1600dgr2
define Device/iodata_wn-ag300dgr
SOC := ar1022
DEVICE_VENDOR := I-O DATA
DEVICE_MODEL := WN-AG300DGR
IMAGE_SIZE := 15424k
IMAGES += factory.bin
IMAGE/factory.bin := append-kernel | pad-to $$$$(BLOCKSIZE) | \
append-rootfs | pad-rootfs | check-size | \
senao-header -r 0x30a -p 0x47 -t 2
DEVICE_PACKAGES := kmod-usb2
endef
TARGET_DEVICES += iodata_wn-ag300dgr
define Device/jjplus_ja76pf2
SOC := ar7161
DEVICE_VENDOR := jjPlus
DEVICE_MODEL := JA76PF2
DEVICE_PACKAGES += -kmod-ath9k -swconfig -wpad-basic-wolfssl -uboot-envtools fconfig
IMAGES += kernel.bin rootfs.bin
IMAGE/kernel.bin := append-kernel
IMAGE/rootfs.bin := append-rootfs | pad-rootfs
IMAGE/sysupgrade.bin := append-rootfs | pad-rootfs | combined-image | \
append-metadata | check-size
KERNEL := kernel-bin | append-dtb | lzma | pad-to $$(BLOCKSIZE)
KERNEL_INITRAMFS := kernel-bin | append-dtb
IMAGE_SIZE := 16000k
SUPPORTED_DEVICES += ja76pf2
endef
TARGET_DEVICES += jjplus_ja76pf2
define Device/librerouter_librerouter-v1
SOC := qca9558
DEVICE_VENDOR := Librerouter
DEVICE_MODEL := LibreRouter
DEVICE_VARIANT := v1
IMAGE_SIZE := 7936k
DEVICE_PACKAGES := kmod-usb2
endef
TARGET_DEVICES += librerouter_librerouter-v1
define Device/meraki_mr16
SOC := ar7161
DEVICE_VENDOR := Meraki
DEVICE_MODEL := MR16
IMAGE_SIZE := 15616k
DEVICE_PACKAGES := kmod-owl-loader
SUPPORTED_DEVICES += mr16
DEVICE_COMPAT_VERSION := 2.0
DEVICE_COMPAT_MESSAGE := Partitions differ from ar71xx version of MR16. Image format is incompatible. \
To use sysupgrade, you must change /lib/update/common.sh::get_image to prepend 128K zeroes to this image, \
and change the bootcmd in u-boot to "bootm 0xbf0a0000". After that, you can use "sysupgrade -F". \
For more details, see the OpenWrt Wiki: https://openwrt.org/toh/meraki/mr16, \
or the commit message of the MR16 ath79 port on git.openwrt.org.
endef
TARGET_DEVICES += meraki_mr16
define Device/mercury_mw4530r-v1
$(Device/tplink-8mlzma)
SOC := ar9344
DEVICE_VENDOR := Mercury
DEVICE_MODEL := MW4530R
DEVICE_VARIANT := v1
DEVICE_PACKAGES := kmod-usb2 kmod-usb-ledtrig-usbport
TPLINK_HWID := 0x45300001
SUPPORTED_DEVICES += tl-wdr4300
endef
TARGET_DEVICES += mercury_mw4530r-v1
define Device/nec_wg1200cr
SOC := qca9563
DEVICE_VENDOR := NEC
DEVICE_MODEL := Aterm WG1200CR
IMAGE_SIZE := 7616k
SEAMA_MTDBLOCK := 6
SEAMA_SIGNATURE := wrgac72_necpf.2016gui_wg1200cr
IMAGES += factory.bin
IMAGE/default := append-kernel | pad-offset $$$$(BLOCKSIZE) 64 | append-rootfs
IMAGE/sysupgrade.bin := $$(IMAGE/default) | seama | pad-rootfs | \
append-metadata | check-size
IMAGE/factory.bin := $$(IMAGE/default) | pad-rootfs -x 64 | seama | \
seama-seal | nec-enc 9gsiy9nzep452pad | check-size
DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca9888-ct
endef
TARGET_DEVICES += nec_wg1200cr
define Device/nec_wg800hp
SOC := qca9563
DEVICE_VENDOR := NEC
DEVICE_MODEL := Aterm WG800HP
IMAGE_SIZE := 7104k
IMAGES += factory.bin
IMAGE/factory.bin := append-kernel | pad-to $$$$(BLOCKSIZE) | \
append-rootfs | pad-rootfs | check-size | \
xor-image -p 6A57190601121E4C004C1E1201061957 -x | nec-fw LASER_ATERM
DEVICE_PACKAGES := kmod-ath10k-ct-smallbuffers ath10k-firmware-qca9887-ct-full-htt
endef
TARGET_DEVICES += nec_wg800hp
define Device/netgear_ex6400_ex7300
$(Device/netgear_generic)
SOC := qca9558
UIMAGE_MAGIC := 0x27051956
NETGEAR_BOARD_ID := EX7300series
NETGEAR_HW_ID := 29765104+16+0+128
IMAGE_SIZE := 15552k
IMAGE/default := append-kernel | pad-offset $$$$(BLOCKSIZE) 64 | \
netgear-rootfs | pad-rootfs
IMAGE/sysupgrade.bin := $$(IMAGE/default) | append-metadata | \
check-size
IMAGE/factory.img := $$(IMAGE/default) | netgear-dni | \
check-size
DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca99x0-ct
endef
define Device/netgear_ex6400
$(Device/netgear_ex6400_ex7300)
DEVICE_MODEL := EX6400
endef
TARGET_DEVICES += netgear_ex6400
define Device/netgear_ex7300
$(Device/netgear_ex6400_ex7300)
DEVICE_MODEL := EX7300
endef
TARGET_DEVICES += netgear_ex7300
define Device/netgear_wndr3x00
$(Device/netgear_generic)
SOC := ar7161
DEVICE_PACKAGES := kmod-usb-ohci kmod-usb2 kmod-usb-ledtrig-usbport \
kmod-leds-reset kmod-owl-loader
endef
define Device/netgear_wndr3700
$(Device/netgear_wndr3x00)
DEVICE_MODEL := WNDR3700
DEVICE_VARIANT := v1
UIMAGE_MAGIC := 0x33373030
NETGEAR_BOARD_ID := WNDR3700
IMAGE_SIZE := 7680k
IMAGES += factory-NA.img
IMAGE/factory-NA.img := $$(IMAGE/default) | netgear-dni NA | \
check-size
SUPPORTED_DEVICES += wndr3700
endef
TARGET_DEVICES += netgear_wndr3700
define Device/netgear_wndr3700-v2
$(Device/netgear_wndr3x00)
DEVICE_MODEL := WNDR3700
DEVICE_VARIANT := v2
UIMAGE_MAGIC := 0x33373031
NETGEAR_BOARD_ID := WNDR3700v2
NETGEAR_HW_ID := 29763654+16+64
IMAGE_SIZE := 15872k
SUPPORTED_DEVICES += wndr3700 netgear,wndr3700v2
endef
TARGET_DEVICES += netgear_wndr3700-v2
define Device/netgear_wndr3800
$(Device/netgear_wndr3x00)
DEVICE_MODEL := WNDR3800
UIMAGE_MAGIC := 0x33373031
NETGEAR_BOARD_ID := WNDR3800
NETGEAR_HW_ID := 29763654+16+128
IMAGE_SIZE := 15872k
SUPPORTED_DEVICES += wndr3700
endef
TARGET_DEVICES += netgear_wndr3800
define Device/netgear_wndr3800ch
$(Device/netgear_wndr3x00)
DEVICE_MODEL := WNDR3800CH
UIMAGE_MAGIC := 0x33373031
NETGEAR_BOARD_ID := WNDR3800CH
NETGEAR_HW_ID := 29763654+16+128
IMAGE_SIZE := 15872k
SUPPORTED_DEVICES += wndr3700
endef
TARGET_DEVICES += netgear_wndr3800ch
define Device/netgear_wndrmac-v1
$(Device/netgear_wndr3x00)
DEVICE_MODEL := WNDRMAC
DEVICE_VARIANT := v1
UIMAGE_MAGIC := 0x33373031
NETGEAR_BOARD_ID := WNDRMAC
NETGEAR_HW_ID := 29763654+16+64
IMAGE_SIZE := 15872k
SUPPORTED_DEVICES += wndr3700
endef
TARGET_DEVICES += netgear_wndrmac-v1
define Device/netgear_wndrmac-v2
$(Device/netgear_wndr3x00)
DEVICE_MODEL := WNDRMAC
DEVICE_VARIANT := v2
UIMAGE_MAGIC := 0x33373031
NETGEAR_BOARD_ID := WNDRMACv2
NETGEAR_HW_ID := 29763654+16+128
IMAGE_SIZE := 15872k
SUPPORTED_DEVICES += wndr3700
endef
TARGET_DEVICES += netgear_wndrmac-v2
define Device/netgear_wnr2200_common
$(Device/netgear_generic)
SOC := ar7241
DEVICE_MODEL := WNR2200
DEVICE_PACKAGES := kmod-usb2 kmod-usb-ledtrig-usbport
UIMAGE_MAGIC := 0x32323030
NETGEAR_BOARD_ID := wnr2200
endef
define Device/netgear_wnr2200-8m
$(Device/netgear_wnr2200_common)
DEVICE_VARIANT := 8M
NETGEAR_HW_ID := 29763600+08+64
IMAGE_SIZE := 7808k
IMAGES += factory-NA.img
IMAGE/factory-NA.img := $$(IMAGE/default) | netgear-dni NA | \
check-size
SUPPORTED_DEVICES += wnr2200
endef
TARGET_DEVICES += netgear_wnr2200-8m
define Device/netgear_wnr2200-16m
$(Device/netgear_wnr2200_common)
DEVICE_VARIANT := 16M
DEVICE_ALT0_VENDOR := NETGEAR
DEVICE_ALT0_MODEL := WNR2200
DEVICE_ALT0_VARIANT := CN/RU
NETGEAR_HW_ID :=
IMAGE_SIZE := 16000k
endef
TARGET_DEVICES += netgear_wnr2200-16m
define Device/ocedo_koala
SOC := qca9558
DEVICE_VENDOR := Ocedo
DEVICE_MODEL := Koala
DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca988x-ct
SUPPORTED_DEVICES += koala
IMAGE_SIZE := 7424k
endef
TARGET_DEVICES += ocedo_koala
define Device/ocedo_raccoon
SOC := ar9344
DEVICE_VENDOR := Ocedo
DEVICE_MODEL := Raccoon
IMAGE_SIZE := 7424k
endef
TARGET_DEVICES += ocedo_raccoon
define Device/ocedo_ursus
SOC := qca9558
DEVICE_VENDOR := Ocedo
DEVICE_MODEL := Ursus
DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca988x-ct
IMAGE_SIZE := 7424k
endef
TARGET_DEVICES += ocedo_ursus
define Device/openmesh_mr600-common
SOC := ar9344
DEVICE_VENDOR := OpenMesh
DEVICE_MODEL := MR600
DEVICE_PACKAGES := uboot-envtools
IMAGE_SIZE := 7808k
BLOCKSIZE := 64k
KERNEL := kernel-bin | append-dtb | lzma | uImage lzma | \
pad-to $$(BLOCKSIZE)
IMAGE/sysupgrade.bin := append-rootfs | pad-rootfs | \
openmesh-image ce_type=MR600 | append-metadata
endef
define Device/openmesh_mr600-v1
$(Device/openmesh_mr600-common)
DEVICE_VARIANT := v1
SUPPORTED_DEVICES += mr600
endef
TARGET_DEVICES += openmesh_mr600-v1
define Device/openmesh_mr600-v2
$(Device/openmesh_mr600-common)
DEVICE_VARIANT := v2
SUPPORTED_DEVICES += mr600v2
endef
TARGET_DEVICES += openmesh_mr600-v2
define Device/openmesh_om2p-common
DEVICE_VENDOR := OpenMesh
DEVICE_PACKAGES := uboot-envtools
IMAGE_SIZE := 7168k
BLOCKSIZE := 256k
KERNEL := kernel-bin | append-dtb | lzma | uImage lzma | \
pad-to $$(BLOCKSIZE)
IMAGE/sysupgrade.bin := append-rootfs | pad-rootfs | \
openmesh-image ce_type=OM2P | append-metadata
endef
define Device/openmesh_om2p-v2
$(Device/openmesh_om2p-common)
SOC := ar9330
DEVICE_MODEL := OM2P
DEVICE_VARIANT := v2
SUPPORTED_DEVICES += om2pv2
endef
TARGET_DEVICES += openmesh_om2p-v2
define Device/openmesh_om2p-v4
$(Device/openmesh_om2p-common)
SOC := qca9533
DEVICE_MODEL := OM2P
DEVICE_VARIANT := v4
SUPPORTED_DEVICES += om2pv4
endef
TARGET_DEVICES += openmesh_om2p-v4
define Device/openmesh_om2p-hs-v1
$(Device/openmesh_om2p-common)
SOC := ar9341
DEVICE_MODEL := OM2P-HS
DEVICE_VARIANT := v1
SUPPORTED_DEVICES += om2p-hs
endef
TARGET_DEVICES += openmesh_om2p-hs-v1
define Device/openmesh_om2p-hs-v2
$(Device/openmesh_om2p-common)
SOC := ar9341
DEVICE_MODEL := OM2P-HS
DEVICE_VARIANT := v2
SUPPORTED_DEVICES += om2p-hsv2
endef
TARGET_DEVICES += openmesh_om2p-hs-v2
define Device/openmesh_om2p-hs-v3
$(Device/openmesh_om2p-common)
SOC := ar9341
DEVICE_MODEL := OM2P-HS
DEVICE_VARIANT := v3
SUPPORTED_DEVICES += om2p-hsv3
endef
TARGET_DEVICES += openmesh_om2p-hs-v3
define Device/openmesh_om2p-hs-v4
$(Device/openmesh_om2p-common)
SOC := qca9533
DEVICE_MODEL := OM2P-HS
DEVICE_VARIANT := v4
SUPPORTED_DEVICES += om2p-hsv4
endef
TARGET_DEVICES += openmesh_om2p-hs-v4
define Device/openmesh_om2p-lc
$(Device/openmesh_om2p-common)
SOC := ar9330
DEVICE_MODEL := OM2P-LC
SUPPORTED_DEVICES += om2p-lc
endef
TARGET_DEVICES += openmesh_om2p-lc
define Device/openmesh_om5p-common
SOC := ar9344
DEVICE_VENDOR := OpenMesh
DEVICE_PACKAGES := uboot-envtools
IMAGE_SIZE := 7808k
BLOCKSIZE := 64k
KERNEL := kernel-bin | append-dtb | lzma | uImage lzma | \
pad-to $$(BLOCKSIZE)
IMAGE/sysupgrade.bin := append-rootfs | pad-rootfs | \
openmesh-image ce_type=OM5P | append-metadata
endef
define Device/openmesh_om5p
$(Device/openmesh_om5p-common)
DEVICE_MODEL := OM5P
SUPPORTED_DEVICES += om5p
endef
TARGET_DEVICES += openmesh_om5p
define Device/openmesh_om5p-ac-v2
SOC := qca9558
DEVICE_VENDOR := OpenMesh
DEVICE_MODEL := OM5P-AC
DEVICE_VARIANT := v2
DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca988x-ct om-watchdog
IMAGE_SIZE := 7808k
SUPPORTED_DEVICES += om5p-acv2
endef
TARGET_DEVICES += openmesh_om5p-ac-v2
define Device/pcs_cap324
SOC := ar9344
DEVICE_VENDOR := PowerCloud Systems
DEVICE_MODEL := CAP324
IMAGE_SIZE := 16000k
SUPPORTED_DEVICES += cap324
endef
TARGET_DEVICES += pcs_cap324
define Device/pcs_cr3000
SOC := ar9341
DEVICE_VENDOR := PowerCloud Systems
DEVICE_MODEL := CR3000
IMAGE_SIZE := 7808k
SUPPORTED_DEVICES += cr3000
endef
TARGET_DEVICES += pcs_cr3000
define Device/pcs_cr5000
SOC := ar9344
DEVICE_VENDOR := PowerCloud Systems
DEVICE_MODEL := CR5000
DEVICE_PACKAGES := kmod-usb2
IMAGE_SIZE := 7808k
SUPPORTED_DEVICES += cr5000
endef
TARGET_DEVICES += pcs_cr5000
define Device/phicomm_k2t
SOC := qca9563
DEVICE_VENDOR := Phicomm
DEVICE_MODEL := K2T
IMAGE_SIZE := 15744k
IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | \
append-metadata | check-size
DEVICE_PACKAGES := kmod-leds-reset kmod-ath10k-ct-smallbuffers ath10k-firmware-qca9888-ct
endef
TARGET_DEVICES += phicomm_k2t
define Device/pisen_ts-d084
$(Device/tplink-8mlzma)
SOC := ar9331
DEVICE_VENDOR := PISEN
DEVICE_MODEL := TS-D084
DEVICE_PACKAGES := kmod-usb-chipidea2
TPLINK_HWID := 0x07030101
endef
TARGET_DEVICES += pisen_ts-d084
define Device/pisen_wmb001n
SOC := ar9341
DEVICE_VENDOR := PISEN
DEVICE_MODEL := WMB001N
IMAGE_SIZE := 14080k
DEVICE_PACKAGES := kmod-i2c-gpio kmod-usb2
LOADER_TYPE := bin
LOADER_FLASH_OFFS := 0x20000
COMPILE := loader-$(1).bin loader-$(1).uImage
COMPILE/loader-$(1).bin := loader-okli-compile
COMPILE/loader-$(1).uImage := append-loader-okli $(1) | pad-to 64k | lzma | \
uImage lzma
KERNEL := kernel-bin | append-dtb | lzma | uImage lzma -M 0x4f4b4c49
IMAGES += factory.bin
IMAGE/factory.bin := $$(IMAGE/sysupgrade.bin) | pisen_wmb001n-factory $(1)
endef
TARGET_DEVICES += pisen_wmb001n
define Device/pisen_wmm003n
$(Device/tplink-8mlzma)
SOC := ar9331
DEVICE_VENDOR := PISEN
DEVICE_MODEL := Cloud Easy Power (WMM003N)
DEVICE_PACKAGES := kmod-usb-chipidea2
TPLINK_HWID := 0x07030101
endef
TARGET_DEVICES += pisen_wmm003n
define Device/plasmacloud_pa300-common
SOC := qca9533
DEVICE_VENDOR := Plasma Cloud
DEVICE_PACKAGES := uboot-envtools
IMAGE_SIZE := 7168k
BLOCKSIZE := 64k
IMAGES += factory.bin
KERNEL := kernel-bin | append-dtb | lzma | uImage lzma | pad-to $$(BLOCKSIZE)
IMAGE/factory.bin := append-rootfs | pad-rootfs | openmesh-image ce_type=PA300
IMAGE/sysupgrade.bin := append-rootfs | pad-rootfs | sysupgrade-tar rootfs=$$$$@ | append-metadata
endef
define Device/plasmacloud_pa300
$(Device/plasmacloud_pa300-common)
DEVICE_MODEL := PA300
endef
TARGET_DEVICES += plasmacloud_pa300
define Device/plasmacloud_pa300e
$(Device/plasmacloud_pa300-common)
DEVICE_MODEL := PA300E
endef
TARGET_DEVICES += plasmacloud_pa300e
define Device/qihoo_c301
$(Device/seama)
SOC := ar9344
DEVICE_VENDOR := Qihoo
DEVICE_MODEL := C301
DEVICE_PACKAGES := kmod-usb2 kmod-ath10k-ct ath10k-firmware-qca988x-ct \
uboot-envtools
IMAGE_SIZE := 15744k
SEAMA_SIGNATURE := wrgac26_qihoo360_360rg
SUPPORTED_DEVICES += qihoo-c301
endef
TARGET_DEVICES += qihoo_c301
define Device/qxwlan_e1700ac-v2
SOC := qca9563
DEVICE_VENDOR := Qxwlan
DEVICE_MODEL := E1700AC
DEVICE_PACKAGES := kmod-usb2 kmod-ath10k-ct ath10k-firmware-qca988x-ct
SUPPORTED_DEVICES += e1700ac-v2
endef
define Device/qxwlan_e1700ac-v2-16m
$(Device/qxwlan_e1700ac-v2)
DEVICE_VARIANT := v2 (16M)
IMAGE_SIZE := 15936k
endef
TARGET_DEVICES += qxwlan_e1700ac-v2-16m
define Device/qxwlan_e1700ac-v2-8m
$(Device/qxwlan_e1700ac-v2)
DEVICE_VARIANT := v2 (8M)
IMAGE_SIZE := 7744k
endef
TARGET_DEVICES += qxwlan_e1700ac-v2-8m
define Device/qxwlan_e558-v2
SOC := qca9558
DEVICE_VENDOR := Qxwlan
DEVICE_MODEL := E558
DEVICE_PACKAGES := kmod-usb2
SUPPORTED_DEVICES += e558-v2
endef
define Device/qxwlan_e558-v2-16m
$(Device/qxwlan_e558-v2)
DEVICE_VARIANT := v2 (16M)
IMAGE_SIZE := 15936k
endef
TARGET_DEVICES += qxwlan_e558-v2-16m
define Device/qxwlan_e558-v2-8m
$(Device/qxwlan_e558-v2)
DEVICE_VARIANT := v2 (8M)
IMAGE_SIZE := 7744k
endef
TARGET_DEVICES += qxwlan_e558-v2-8m
define Device/qxwlan_e600g-v2
SOC := qca9531
DEVICE_VENDOR := Qxwlan
DEVICE_MODEL := E600G
DEVICE_PACKAGES := kmod-usb2
SUPPORTED_DEVICES += e600g-v2
endef
define Device/qxwlan_e600g-v2-16m
$(Device/qxwlan_e600g-v2)
DEVICE_VARIANT := v2 (16M)
IMAGE_SIZE := 15936k
endef
TARGET_DEVICES += qxwlan_e600g-v2-16m
define Device/qxwlan_e600g-v2-8m
$(Device/qxwlan_e600g-v2)
DEVICE_VARIANT := v2 (8M)
IMAGE_SIZE := 7744k
endef
TARGET_DEVICES += qxwlan_e600g-v2-8m
define Device/qxwlan_e600gac-v2
SOC := qca9531
DEVICE_VENDOR := Qxwlan
DEVICE_MODEL := E600GAC
DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca9887-ct
SUPPORTED_DEVICES += e600gac-v2
endef
define Device/qxwlan_e600gac-v2-16m
$(Device/qxwlan_e600gac-v2)
DEVICE_VARIANT := v2 (16M)
IMAGE_SIZE := 15936k
endef
TARGET_DEVICES += qxwlan_e600gac-v2-16m
define Device/qxwlan_e600gac-v2-8m
$(Device/qxwlan_e600gac-v2)
DEVICE_VARIANT := v2 (8M)
IMAGE_SIZE := 7744k
endef
TARGET_DEVICES += qxwlan_e600gac-v2-8m
define Device/qxwlan_e750a-v4
SOC := ar9344
DEVICE_VENDOR := Qxwlan
DEVICE_MODEL := E750A
DEVICE_PACKAGES := kmod-usb2
SUPPORTED_DEVICES += e750a-v4
endef
define Device/qxwlan_e750a-v4-16m
$(Device/qxwlan_e750a-v4)
DEVICE_VARIANT := v4 (16M)
IMAGE_SIZE := 15936k
endef
TARGET_DEVICES += qxwlan_e750a-v4-16m
define Device/qxwlan_e750a-v4-8m
$(Device/qxwlan_e750a-v4)
DEVICE_VARIANT := v4 (8M)
IMAGE_SIZE := 7744k
endef
TARGET_DEVICES += qxwlan_e750a-v4-8m
define Device/qxwlan_e750g-v8
SOC := ar9344
DEVICE_VENDOR := Qxwlan
DEVICE_MODEL := E750G
DEVICE_PACKAGES := kmod-usb2
SUPPORTED_DEVICES += e750g-v8
endef
define Device/qxwlan_e750g-v8-16m
$(Device/qxwlan_e750g-v8)
DEVICE_VARIANT := v8 (16M)
IMAGE_SIZE := 15936k
endef
TARGET_DEVICES += qxwlan_e750g-v8-16m
define Device/qxwlan_e750g-v8-8m
$(Device/qxwlan_e750g-v8)
DEVICE_VARIANT := v8 (8M)
IMAGE_SIZE := 7744k
endef
TARGET_DEVICES += qxwlan_e750g-v8-8m
define Device/rosinson_wr818
SOC := qca9563
DEVICE_VENDOR := Rosinson
DEVICE_MODEL := WR818
IMAGE_SIZE := 15872k
DEVICE_PACKAGES := kmod-usb2 kmod-usb-ledtrig-usbport
endef
TARGET_DEVICES += rosinson_wr818
define Device/samsung_wam250
SOC := ar9344
DEVICE_VENDOR := Samsung
DEVICE_MODEL := WAM250
IMAGE_SIZE := 15872k
DEVICE_PACKAGES := kmod-usb2
SUPPORTED_DEVICES += wam250
endef
TARGET_DEVICES += samsung_wam250
define Device/siemens_ws-ap3610
SOC := ar7161
DEVICE_VENDOR := Siemens
DEVICE_MODEL := WS-AP3610
IMAGE_SIZE := 14336k
BLOCKSIZE := 256k
LOADER_TYPE := bin
LOADER_FLASH_OFFS := 0x82000
COMPILE := loader-$(1).bin
COMPILE/loader-$(1).bin := loader-okli-compile
KERNEL := kernel-bin | append-dtb | lzma | uImage lzma -M 0x4f4b4c49 | loader-okli $(1) 8128 | uImage none
KERNEL_INITRAMFS := kernel-bin | append-dtb | uImage none
endef
TARGET_DEVICES += siemens_ws-ap3610
define Device/sitecom_wlr-7100
SOC := ar1022
DEVICE_VENDOR := Sitecom
DEVICE_MODEL := WLR-7100
DEVICE_PACKAGES := ath10k-firmware-qca988x-ct kmod-ath10k-ct-smallbuffers kmod-usb2
IMAGES += factory.dlf
IMAGE/factory.dlf := append-kernel | pad-to $$$$(BLOCKSIZE) | \
append-rootfs | pad-rootfs | check-size | \
senao-header -r 0x222 -p 0x53 -t 2
IMAGE_SIZE := 7488k
endef
TARGET_DEVICES += sitecom_wlr-7100
define Device/sitecom_wlr-8100
SOC := qca9558
DEVICE_VENDOR := Sitecom
DEVICE_MODEL := WLR-8100
DEVICE_ALT0_VENDOR := Sitecom
DEVICE_ALT0_MODEL := X8 AC1750
DEVICE_PACKAGES := ath10k-firmware-qca988x-ct kmod-ath10k-ct kmod-usb2 kmod-usb3
SUPPORTED_DEVICES += wlr8100
IMAGES += factory.dlf
IMAGE/factory.dlf := append-kernel | pad-to $$$$(BLOCKSIZE) | \
append-rootfs | pad-rootfs | check-size | \
senao-header -r 0x222 -p 0x56 -t 2
IMAGE_SIZE := 15424k
endef
TARGET_DEVICES += sitecom_wlr-8100
define Device/telco_t1
SOC := qca9531
DEVICE_VENDOR := Telco
DEVICE_MODEL := T1
DEVICE_PACKAGES := kmod-usb2 kmod-usb-net-qmi-wwan \
kmod-usb-serial-option uqmi -swconfig -uboot-envtools
IMAGE_SIZE := 16192k
SUPPORTED_DEVICES += telco_electronics,tel-t1
endef
TARGET_DEVICES += telco_t1
define Device/teltonika_rut955
SOC := ar9344
DEVICE_VENDOR := Teltonika
DEVICE_MODEL := RUT955
DEVICE_PACKAGES := kmod-usb2 kmod-usb-acm kmod-usb-net-qmi-wwan \
kmod-usb-serial-option kmod-hwmon-mcp3021 uqmi -uboot-envtools
IMAGE_SIZE := 15552k
TPLINK_HWID := 0x35000001
TPLINK_HWREV := 0x1
TPLINK_HEADER_VERSION := 1
KERNEL := kernel-bin | append-dtb | lzma | tplink-v1-header
KERNEL_INITRAMFS := kernel-bin | append-dtb | lzma | uImage lzma
IMAGES += factory.bin
IMAGE/factory.bin := append-kernel | pad-to $$$$(BLOCKSIZE) | append-rootfs |\
pad-rootfs | teltonika-fw-fake-checksum | append-string master |\
append-md5sum-bin | check-size
IMAGE/sysupgrade.bin := append-kernel | pad-to $$$$(BLOCKSIZE) |\
append-rootfs | pad-rootfs | append-metadata |\
check-size
endef
TARGET_DEVICES += teltonika_rut955
define Device/teltonika_rut955-h7v3c0
$(Device/teltonika_rut955)
DEVICE_VARIANT := H7V3C0
endef
TARGET_DEVICES += teltonika_rut955-h7v3c0
define Device/trendnet_tew-823dru
SOC := qca9558
DEVICE_VENDOR := Trendnet
DEVICE_MODEL := TEW-823DRU
DEVICE_VARIANT := v1.0R
DEVICE_PACKAGES := kmod-usb2 kmod-ath10k-ct ath10k-firmware-qca988x-ct
SUPPORTED_DEVICES += tew-823dru
IMAGE_SIZE := 15296k
IMAGES := factory.bin sysupgrade.bin
IMAGE/default := append-kernel | pad-to $$$$(BLOCKSIZE) | append-rootfs | \
pad-rootfs
IMAGE/factory.bin := $$(IMAGE/default) | pad-offset $$$$(IMAGE_SIZE) 26 | \
append-string 00AP135AR9558-RT-131129-00 | check-size
IMAGE/sysupgrade.bin := $$(IMAGE/default) | append-metadata | \
check-size
endef
TARGET_DEVICES += trendnet_tew-823dru
define Device/wallys_dr531
SOC := qca9531
DEVICE_VENDOR := Wallys
DEVICE_MODEL := DR531
DEVICE_PACKAGES := kmod-usb2 rssileds
IMAGE_SIZE := 7808k
SUPPORTED_DEVICES += dr531
endef
TARGET_DEVICES += wallys_dr531
define Device/wd_mynet-n750
$(Device/seama)
SOC := ar9344
DEVICE_VENDOR := Western Digital
DEVICE_MODEL := My Net N750
IMAGE_SIZE := 15872k
DEVICE_PACKAGES := kmod-usb2
SEAMA_SIGNATURE := wrgnd13_wd_av
SUPPORTED_DEVICES += mynet-n750
endef
TARGET_DEVICES += wd_mynet-n750
define Device/wd_mynet-wifi-rangeextender
SOC := ar9344
DEVICE_VENDOR := Western Digital
DEVICE_MODEL := My Net Wi-Fi Range Extender
DEVICE_PACKAGES := rssileds nvram -swconfig
IMAGE_SIZE := 7808k
ADDPATTERN_ID := mynet-rext
ADDPATTERN_VERSION := 1.00.01
IMAGE/sysupgrade.bin := append-rootfs | pad-rootfs | cybertan-trx | \
addpattern | append-metadata
SUPPORTED_DEVICES += mynet-rext
endef
TARGET_DEVICES += wd_mynet-wifi-rangeextender
define Device/winchannel_wb2000
SOC := ar9344
DEVICE_VENDOR := Winchannel
DEVICE_MODEL := WB2000
IMAGE_SIZE := 15872k
DEVICE_PACKAGES := kmod-i2c-gpio kmod-rtc-ds1307 kmod-usb2 \
kmod-usb-ledtrig-usbport
endef
TARGET_DEVICES += winchannel_wb2000
define Device/xiaomi_mi-router-4q
SOC := qca9561
DEVICE_VENDOR := Xiaomi
DEVICE_MODEL := Mi Router 4Q
IMAGE_SIZE := 14336k
endef
TARGET_DEVICES += xiaomi_mi-router-4q
define Device/yuncore_a770
SOC := qca9531
DEVICE_VENDOR := YunCore
DEVICE_MODEL := A770
DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca9887-ct
IMAGE_SIZE := 16000k
IMAGES += tftp.bin
IMAGE/tftp.bin := $$(IMAGE/sysupgrade.bin) | yuncore-tftp-header-16m
endef
TARGET_DEVICES += yuncore_a770
define Device/yuncore_a782
SOC := qca9563
DEVICE_VENDOR := YunCore
DEVICE_MODEL := A782
DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca9888-ct
IMAGE_SIZE := 16000k
IMAGES += tftp.bin
IMAGE/tftp.bin := $$(IMAGE/sysupgrade.bin) | yuncore-tftp-header-16m
endef
TARGET_DEVICES += yuncore_a782
define Device/yuncore_xd4200
SOC := qca9563
DEVICE_VENDOR := YunCore
DEVICE_MODEL := XD4200
DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca9888-ct
IMAGE_SIZE := 16000k
IMAGES += tftp.bin
IMAGE/tftp.bin := $$(IMAGE/sysupgrade.bin) | yuncore-tftp-header-16m
endef
TARGET_DEVICES += yuncore_xd4200
define Device/zbtlink_zbt-wd323
SOC := ar9344
DEVICE_VENDOR := ZBT
DEVICE_MODEL := WD323
IMAGE_SIZE := 16000k
DEVICE_PACKAGES := kmod-usb2 kmod-i2c-gpio kmod-rtc-pcf8563 \
kmod-usb-serial kmod-usb-serial-cp210x uqmi
endef
TARGET_DEVICES += zbtlink_zbt-wd323
define Device/zyxel_nbg6616
SOC := qca9557
DEVICE_VENDOR := ZyXEL
DEVICE_MODEL := NBG6616
DEVICE_PACKAGES := kmod-usb2 kmod-usb-ledtrig-usbport kmod-rtc-pcf8563 \
kmod-ath10k-ct ath10k-firmware-qca988x-ct
IMAGE_SIZE := 15232k
RAS_BOARD := NBG6616
RAS_ROOTFS_SIZE := 14464k
RAS_VERSION := "OpenWrt Linux-$(LINUX_VERSION)"
IMAGES += factory.bin
IMAGE/factory.bin := append-kernel | pad-to $$$$(BLOCKSIZE) | \
append-rootfs | pad-rootfs | pad-to 64k | check-size | zyxel-ras-image
SUPPORTED_DEVICES += nbg6616
endef
TARGET_DEVICES += zyxel_nbg6616