mirror of
https://github.com/openwrt/openwrt.git
synced 2024-12-20 14:13:16 +00:00
3baa45fbd8
The Comtrend VR-3025un is a wifi gigabit router, 2.4 GHz single band with two external antennas. Hardware: - SoC: Broadcom BCM6368 - CPU: dual core BMIPS4350 @ 400Mhz - RAM: 64 MB DDR - Flash: 8 MB parallel NOR - Ethernet LAN: 4x 100Mbit - Wifi 2.4 GHz: miniPCI Broadcom BCM43222 802.11bgn - USB: 1x 2.0 - Buttons: 1x (reset) - LEDs: yes - UART: yes Installation via CFE web UI: 1. Power off the router. 2. Press reset button near the antenna. 3. Keep it pressed while powering up during ~20+ seconds. 4. Browse to http://192.168.1.1 and upload the firmware. 5. Wait a few minutes for it to finish. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
183 lines
2.7 KiB
Plaintext
183 lines
2.7 KiB
Plaintext
// SPDX-License-Identifier: GPL-2.0-or-later
|
|
|
|
#include "bcm6368.dtsi"
|
|
|
|
/ {
|
|
model = "Comtrend VR-3025un";
|
|
compatible = "comtrend,vr-3025un", "brcm,bcm6368";
|
|
|
|
aliases {
|
|
led-boot = &led_power_green;
|
|
led-failsafe = &led_power_red;
|
|
led-running = &led_power_green;
|
|
led-upgrade = &led_power_green;
|
|
};
|
|
|
|
keys {
|
|
compatible = "gpio-keys-polled";
|
|
poll-interval = <100>;
|
|
|
|
reset {
|
|
label = "reset";
|
|
gpios = <&gpio 34 GPIO_ACTIVE_LOW>;
|
|
linux,code = <KEY_RESTART>;
|
|
debounce-interval = <60>;
|
|
};
|
|
};
|
|
|
|
leds {
|
|
compatible = "gpio-leds";
|
|
|
|
led@2 {
|
|
label = "green:dsl";
|
|
gpios = <&gpio 2 GPIO_ACTIVE_LOW>;
|
|
};
|
|
|
|
led@5 {
|
|
label = "green:internet";
|
|
gpios = <&gpio 5 GPIO_ACTIVE_HIGH>;
|
|
};
|
|
|
|
led_power_green: led@22 {
|
|
label = "green:power";
|
|
gpios = <&gpio 22 GPIO_ACTIVE_HIGH>;
|
|
};
|
|
|
|
led_power_red: led@24 {
|
|
label = "red:power";
|
|
gpios = <&gpio 24 GPIO_ACTIVE_HIGH>;
|
|
panic-indicator;
|
|
};
|
|
|
|
led@31 {
|
|
label = "red:internet";
|
|
gpios = <&gpio 31 GPIO_ACTIVE_HIGH>;
|
|
};
|
|
};
|
|
|
|
bcm43222-sprom {
|
|
compatible = "brcm,ssb-sprom";
|
|
|
|
pci-bus = <0>;
|
|
pci-dev = <1>;
|
|
|
|
nvmem-cells = <&macaddr_cfe_6a0>;
|
|
nvmem-cell-names = "mac-address";
|
|
mac-address-increment = <1>;
|
|
|
|
brcm,sprom = "brcm/bcm43222-sprom.bin";
|
|
brcm,sprom-fixups = <97 0xfeb3>,
|
|
<98 0x1618>,
|
|
<99 0xfab0>,
|
|
<113 0xfed1>,
|
|
<114 0x1609>,
|
|
<115 0xfad9>;
|
|
};
|
|
};
|
|
|
|
&ehci {
|
|
status = "okay";
|
|
};
|
|
|
|
ðernet {
|
|
status = "okay";
|
|
|
|
nvmem-cells = <&macaddr_cfe_6a0>;
|
|
nvmem-cell-names = "mac-address";
|
|
};
|
|
|
|
&ohci {
|
|
status = "okay";
|
|
};
|
|
|
|
&pci {
|
|
status = "okay";
|
|
};
|
|
|
|
&pflash {
|
|
status = "okay";
|
|
|
|
partitions {
|
|
compatible = "fixed-partitions";
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
|
|
cfe: partition@0 {
|
|
label = "CFE";
|
|
reg = <0x000000 0x010000>;
|
|
read-only;
|
|
};
|
|
|
|
partition@20000 {
|
|
compatible = "brcm,bcm963xx-imagetag";
|
|
label = "firmware";
|
|
reg = <0x010000 0x7e0000>;
|
|
};
|
|
|
|
partition@1fe0000 {
|
|
label = "nvram";
|
|
reg = <0x7f0000 0x010000>;
|
|
};
|
|
};
|
|
};
|
|
|
|
&pinctrl {
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&pinctrl_ephy0_led &pinctrl_ephy1_led
|
|
&pinctrl_ephy2_led &pinctrl_ephy3_led>;
|
|
};
|
|
|
|
&switch0 {
|
|
ports {
|
|
port@0 {
|
|
reg = <0>;
|
|
label = "lan1";
|
|
|
|
phy-handle = <&phy1>;
|
|
phy-mode = "mii";
|
|
};
|
|
|
|
port@1 {
|
|
reg = <1>;
|
|
label = "lan2";
|
|
|
|
phy-handle = <&phy2>;
|
|
phy-mode = "mii";
|
|
};
|
|
|
|
port@2 {
|
|
reg = <2>;
|
|
label = "lan3";
|
|
|
|
phy-handle = <&phy3>;
|
|
phy-mode = "mii";
|
|
};
|
|
|
|
port@3 {
|
|
reg = <3>;
|
|
label = "iptv";
|
|
|
|
phy-handle = <&phy4>;
|
|
phy-mode = "mii";
|
|
};
|
|
};
|
|
};
|
|
|
|
&uart0 {
|
|
status = "okay";
|
|
};
|
|
|
|
&usbh {
|
|
status = "okay";
|
|
};
|
|
|
|
&cfe {
|
|
compatible = "nvmem-cells";
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
|
|
macaddr_cfe_6a0: macaddr@6a0 {
|
|
reg = <0x6a0 0x6>;
|
|
};
|
|
};
|