mirror of
https://github.com/openwrt/openwrt.git
synced 2024-12-21 06:33:41 +00:00
a04d733e56
ELECOM WRC-1167GS2-B is a 2.4/5 GHz band 11ac (Wi-Fi 5) router, based on MT7621A. Specification: - SoC : MediaTek MT7621A - RAM : DDR3 128 MiB - Flash : SPI-NOR 16 MiB - WLAN : 2.4/5 GHz 2T2R (MediaTek MT7615D) - Ethernet : 10/100/1000 Mbps x5 - Switch : MediaTek MT7530 (SoC) - LED/keys : 6x/6x (2x buttons, 1x slide-switch) - UART : through-hole on PCB - J4: 3.3V, GND, TX, RX from ethernet port side - 57600n8 - Power : 12VDC, 1A MAC addresses: LAN : 04:AB:18:**:**:13 (Factory, 0xFFF4 (hex)) WAN : 04:AB:18:**:**:14 (Factory, 0xFFFA (hex)) 2.4 GHz : 04:AB:18:**:**:15 (none) 5 GHz : 04:AB:18:**:**:16 (Factory, 0x4 (hex)) Flash instruction using factory image: 1. Boot WRC-1167GS2-B normally 2. Access to "http://192.168.2.1/" and open firmware update page ("ファームウェア更新") 3. Select the OpenWrt factory image and click apply ("適用") button 4. Wait ~120 seconds to complete flashing Notes: - there is no way to configure the correct MAC address for secondary phy (5GHz) on MT7615D - Wi-Fi band on primary phy (2.4GHz) cannot be limitted by specifying ieee80211-freq-limit (fail to register secondary phy due to error) - mtd-mac-address in the wifi node is required for using mtd-mac-address-increment Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com> [rebase onto split DTSI patch] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
156 lines
2.3 KiB
Plaintext
156 lines
2.3 KiB
Plaintext
// SPDX-License-Identifier: GPL-2.0-only
|
|
|
|
#include "mt7621.dtsi"
|
|
|
|
#include <dt-bindings/gpio/gpio.h>
|
|
#include <dt-bindings/input/input.h>
|
|
|
|
/ {
|
|
aliases {
|
|
led-boot = &led_power_green;
|
|
led-failsafe = &led_power_green;
|
|
led-running = &led_power_green;
|
|
led-upgrade = &led_power_green;
|
|
label-mac-device = &wan;
|
|
};
|
|
|
|
leds: leds {
|
|
compatible = "gpio-leds";
|
|
|
|
led_power_green: power_green {
|
|
label = "green:power";
|
|
gpios = <&gpio 7 GPIO_ACTIVE_HIGH>;
|
|
};
|
|
|
|
power_blue {
|
|
label = "blue:power";
|
|
gpios = <&gpio 8 GPIO_ACTIVE_HIGH>;
|
|
};
|
|
|
|
wps {
|
|
label = "red:wps";
|
|
gpios = <&gpio 15 GPIO_ACTIVE_HIGH>;
|
|
};
|
|
|
|
power_red {
|
|
label = "red:power";
|
|
gpios = <&gpio 16 GPIO_ACTIVE_HIGH>;
|
|
};
|
|
};
|
|
|
|
keys {
|
|
compatible = "gpio-keys";
|
|
|
|
reset {
|
|
label = "reset";
|
|
gpios = <&gpio 13 GPIO_ACTIVE_LOW>;
|
|
linux,code = <KEY_RESTART>;
|
|
};
|
|
|
|
wps {
|
|
label = "wps";
|
|
gpios = <&gpio 18 GPIO_ACTIVE_LOW>;
|
|
linux,code = <KEY_WPS_BUTTON>;
|
|
};
|
|
|
|
client {
|
|
label = "client";
|
|
gpios = <&gpio 41 GPIO_ACTIVE_LOW>;
|
|
linux,code = <BTN_0>;
|
|
linux,input-type = <EV_SW>;
|
|
};
|
|
|
|
ap {
|
|
label = "ap";
|
|
gpios = <&gpio 42 GPIO_ACTIVE_LOW>;
|
|
linux,code = <BTN_0>;
|
|
linux,input-type = <EV_SW>;
|
|
};
|
|
|
|
extender {
|
|
label = "extender";
|
|
gpios = <&gpio 43 GPIO_ACTIVE_LOW>;
|
|
linux,code = <BTN_0>;
|
|
linux,input-type = <EV_SW>;
|
|
};
|
|
|
|
router {
|
|
label = "router";
|
|
gpios = <&gpio 44 GPIO_ACTIVE_LOW>;
|
|
linux,code = <BTN_0>;
|
|
linux,input-type = <EV_SW>;
|
|
};
|
|
};
|
|
};
|
|
|
|
&switch0 {
|
|
ports {
|
|
wan: port@0 {
|
|
status = "okay";
|
|
label = "wan";
|
|
};
|
|
|
|
port@1 {
|
|
status = "okay";
|
|
label = "lan4";
|
|
};
|
|
|
|
port@2 {
|
|
status = "okay";
|
|
label = "lan3";
|
|
};
|
|
|
|
port@3 {
|
|
status = "okay";
|
|
label = "lan2";
|
|
};
|
|
|
|
port@4 {
|
|
status = "okay";
|
|
label = "lan1";
|
|
};
|
|
};
|
|
};
|
|
|
|
&spi0 {
|
|
status = "okay";
|
|
|
|
flash@0 {
|
|
compatible = "jedec,spi-nor";
|
|
reg = <0>;
|
|
spi-max-frequency = <40000000>;
|
|
|
|
partitions: partitions {
|
|
compatible = "fixed-partitions";
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
|
|
partition@0 {
|
|
label = "u-boot";
|
|
reg = <0x0 0x30000>;
|
|
read-only;
|
|
};
|
|
|
|
partition@30000 {
|
|
label = "u-boot-env";
|
|
reg = <0x30000 0x10000>;
|
|
read-only;
|
|
};
|
|
|
|
factory: partition@40000 {
|
|
label = "factory";
|
|
reg = <0x40000 0x10000>;
|
|
read-only;
|
|
};
|
|
};
|
|
};
|
|
};
|
|
|
|
&pcie {
|
|
status = "okay";
|
|
};
|
|
|
|
&xhci {
|
|
status = "disabled";
|
|
};
|