mirror of
https://github.com/openwrt/openwrt.git
synced 2024-12-26 00:41:17 +00:00
635f111148
In ath79, for several SoCs the console bootargs are defined to the very same value in every device's DTS. Consolidate these definitions in the SoC dtsi files and drop further redundant definitions elsewhere. The only device without any bootargs set has been OpenMesh OM5P-AC V2. This will now inherit the setting from qca955x.dtsi Note that while this tidies up master a lot, it might develop into a frequent pitfall for backports. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
197 lines
3.1 KiB
Plaintext
197 lines
3.1 KiB
Plaintext
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
|
|
|
#include <dt-bindings/gpio/gpio.h>
|
|
#include <dt-bindings/input/input.h>
|
|
|
|
#include "qca956x.dtsi"
|
|
|
|
/ {
|
|
compatible = "glinet,gl-ar750s", "qca,qca9563";
|
|
model = "GL.iNet GL-AR750S";
|
|
|
|
aliases {
|
|
led-boot = &led_power;
|
|
led-failsafe = &led_power;
|
|
led-running = &led_power;
|
|
led-upgrade = &led_power;
|
|
label-mac-device = ð0;
|
|
};
|
|
|
|
keys {
|
|
compatible = "gpio-keys";
|
|
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&jtag_disable_pins>;
|
|
|
|
reset {
|
|
label = "reset";
|
|
linux,code = <KEY_RESTART>;
|
|
gpios = <&gpio 2 GPIO_ACTIVE_LOW>;
|
|
};
|
|
|
|
mode {
|
|
label = "mode";
|
|
linux,code = <BTN_0>;
|
|
linux,input-type = <EV_SW>;
|
|
gpios = <&gpio 8 GPIO_ACTIVE_LOW>;
|
|
};
|
|
};
|
|
|
|
leds {
|
|
compatible = "gpio-leds";
|
|
|
|
led_power: power {
|
|
label = "gl-ar750s:green:power";
|
|
gpios = <&gpio 1 GPIO_ACTIVE_LOW>;
|
|
default-state = "keep";
|
|
};
|
|
|
|
led_wlan2g: wlan2g {
|
|
label = "gl-ar750s:green:wlan2g";
|
|
gpios = <&gpio 19 GPIO_ACTIVE_LOW>;
|
|
linux,default-trigger = "phy1tpt";
|
|
};
|
|
|
|
led_wlan5g: wlan5g {
|
|
label = "gl-ar750s:green:wlan5g";
|
|
gpios = <&gpio 20 GPIO_ACTIVE_HIGH>;
|
|
linux,default-trigger = "phy0tpt";
|
|
};
|
|
};
|
|
|
|
i2c: i2c {
|
|
compatible = "i2c-gpio";
|
|
|
|
sda-gpios = <&gpio 5 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
|
|
scl-gpios = <&gpio 21 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
|
|
};
|
|
};
|
|
|
|
&spi {
|
|
status = "okay";
|
|
|
|
num-cs = <2>;
|
|
|
|
flash_nor: flash@0 {
|
|
compatible = "jedec,spi-nor";
|
|
reg = <0>;
|
|
spi-max-frequency = <25000000>;
|
|
|
|
nor_partitions: partitions {
|
|
compatible = "fixed-partitions";
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
|
|
partition@0 {
|
|
label = "u-boot";
|
|
reg = <0x000000 0x040000>;
|
|
read-only;
|
|
};
|
|
|
|
partition@40000 {
|
|
label = "u-boot-env";
|
|
reg = <0x040000 0x010000>;
|
|
};
|
|
|
|
art: partition@50000 {
|
|
label = "art";
|
|
reg = <0x050000 0x010000>;
|
|
read-only;
|
|
};
|
|
|
|
nor_firmware: partition@60000 {
|
|
label = "nor_firmware";
|
|
reg = <0x060000 0xfa0000>;
|
|
};
|
|
|
|
nor_kernel: partition_alt@60000 {
|
|
label = "nor_kernel";
|
|
reg = <0x060000 0x400000>;
|
|
};
|
|
|
|
nor_reserved: parition_alt@460000 {
|
|
label = "nor_reserved";
|
|
reg = <0x460000 0xba0000>;
|
|
};
|
|
};
|
|
};
|
|
|
|
flash_nand: flash@1 {
|
|
compatible = "spi-nand";
|
|
reg = <1>;
|
|
spi-max-frequency = <25000000>;
|
|
|
|
nand_partitions: partitions {
|
|
compatible = "fixed-partitions";
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
|
|
nand_ubi: partition@0 {
|
|
label = "nand_ubi";
|
|
reg = <0x000000 0x8000000>;
|
|
};
|
|
};
|
|
};
|
|
};
|
|
|
|
ð0 {
|
|
status = "okay";
|
|
|
|
phy-handle = <&phy0>;
|
|
mtd-mac-address = <&art 0x0>;
|
|
};
|
|
|
|
&gpio {
|
|
usb_vbus {
|
|
gpio-hog;
|
|
gpios = <7 GPIO_ACTIVE_HIGH>;
|
|
output-high;
|
|
line-name = "usb-vbus";
|
|
};
|
|
};
|
|
|
|
&mdio0 {
|
|
status = "okay";
|
|
|
|
phy-mask = <0>;
|
|
|
|
phy0: ethernet-phy@0 {
|
|
reg = <0>;
|
|
phy-mode = "sgmii";
|
|
qca,ar8327-initvals = <
|
|
0x04 0x00080080 /* PORT0 PAD MODE CTRL */
|
|
0x7c 0x0000007e /* PORT0_STATUS */
|
|
>;
|
|
};
|
|
};
|
|
|
|
&pcie {
|
|
status = "okay";
|
|
};
|
|
|
|
&uart {
|
|
status = "okay";
|
|
};
|
|
|
|
&usb0 {
|
|
status = "okay";
|
|
};
|
|
|
|
&usb1 {
|
|
status = "okay";
|
|
};
|
|
|
|
&usb_phy0 {
|
|
status = "okay";
|
|
};
|
|
|
|
&usb_phy1 {
|
|
status = "okay";
|
|
};
|
|
|
|
&wmac {
|
|
status = "okay";
|
|
|
|
mtd-cal-data = <&art 0x1000>;
|
|
};
|