mirror of
https://github.com/openwrt/openwrt.git
synced 2025-01-17 18:30:24 +00:00
9ad3967f14
SoC: Qualcomm IPQ4019 (Dakota) 717 MHz, 4 cores
RAM: 256 MiB (Nanya NT5CC128M16IP-DI)
FLASH: 128 MiB (Macronix NAND)
WiFi0: Qualcomm IPQ4019 b/g/n 2x2
WiFi1: Qualcomm IPQ4019 a/n/ac 2x2
WiFi2: Qualcomm Atheros QCA9886 a/n/ac
BT: Atheros AR3012
IN: WPS Button, Reset Button
OUT: RGB-LED via TI LP5523 9-channel Controller
UART: Front of Device - 115200 N-8
Pinout 3.3v - RX - TX - GND (Square is VCC)
Installation:
1. Transfer OpenWRT-initramfs image to the device via SSH to /tmp.
Login credentials are identical to the Web UI.
2. Login to the device via SSH.
3. Flash the initramfs image using
> mtd-write -d linux -i openwrt-image-file
4. Power-cycle the device and wait for OpenWRT to boot.
5. From there flash the OpenWRT-sysupgrade image.
Ethernet-Ports: Although labeled identically, the port next to
the power socket is the LAN port and the other one is WAN. This
is the same behavior as in the stock firmware.
Signed-off-by: Marius Genheimer <mail@f0wl.cc>
[Dropped setup_mac 02_network in favour of 05_set_iface_mac_ipq40xx.sh,
reorderd 02_network entries, added board.bin WA for the QCA9886 from ath79,
minor dts touchup, added rng to 4.19 dts]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
304 lines
10 KiB
Makefile
304 lines
10 KiB
Makefile
include $(TOPDIR)/rules.mk
|
|
include $(INCLUDE_DIR)/image.mk
|
|
|
|
DEVICE_VARS += RAS_BOARD RAS_ROOTFS_SIZE RAS_VERSION
|
|
|
|
define Device/Default
|
|
PROFILES := Default
|
|
KERNEL_DEPENDS = $$(wildcard $(DTS_DIR)/$$(DEVICE_DTS).dts)
|
|
KERNEL_INITRAMFS_PREFIX := $$(IMG_PREFIX)-$(1)-initramfs
|
|
KERNEL_PREFIX := $$(IMAGE_PREFIX)
|
|
KERNEL_LOADADDR := 0x80208000
|
|
SUPPORTED_DEVICES := $(subst _,$(comma),$(1))
|
|
IMAGE/sysupgrade.bin = sysupgrade-tar | append-metadata
|
|
IMAGE/sysupgrade.bin/squashfs :=
|
|
endef
|
|
|
|
define Device/FitImage
|
|
KERNEL_SUFFIX := -fit-uImage.itb
|
|
KERNEL = kernel-bin | gzip | fit gzip $$(DTS_DIR)/$$(DEVICE_DTS).dtb
|
|
KERNEL_NAME := Image
|
|
endef
|
|
|
|
define Device/FitImageLzma
|
|
KERNEL_SUFFIX := -fit-uImage.itb
|
|
KERNEL = kernel-bin | lzma | fit lzma $$(DTS_DIR)/$$(DEVICE_DTS).dtb
|
|
KERNEL_NAME := Image
|
|
endef
|
|
|
|
define Device/FitzImage
|
|
KERNEL_SUFFIX := -fit-zImage.itb
|
|
KERNEL = kernel-bin | fit none $$(DTS_DIR)/$$(DEVICE_DTS).dtb
|
|
KERNEL_NAME := zImage
|
|
endef
|
|
|
|
define Device/UbiFit
|
|
KERNEL_IN_UBI := 1
|
|
IMAGES := nand-factory.ubi nand-sysupgrade.bin
|
|
IMAGE/nand-factory.ubi := append-ubi
|
|
IMAGE/nand-sysupgrade.bin := sysupgrade-tar | append-metadata
|
|
endef
|
|
|
|
define Device/DniImage
|
|
KERNEL_SUFFIX := -fit-uImage.itb
|
|
KERNEL = kernel-bin | gzip | fit gzip $$(DTS_DIR)/$$(DEVICE_DTS).dtb
|
|
KERNEL_NAME := Image
|
|
NETGEAR_BOARD_ID :=
|
|
NETGEAR_HW_ID :=
|
|
IMAGES := factory.img sysupgrade.bin
|
|
IMAGE/factory.img := append-kernel | pad-offset 64k 64 | append-uImage-fakehdr filesystem | append-rootfs | pad-rootfs | netgear-dni
|
|
IMAGE/sysupgrade.bin := append-kernel | pad-offset 64k 64 | append-uImage-fakehdr filesystem | append-rootfs | pad-rootfs | append-metadata
|
|
endef
|
|
DEVICE_VARS += NETGEAR_BOARD_ID NETGEAR_HW_ID
|
|
|
|
|
|
define Device/8dev_jalapeno
|
|
$(call Device/FitImage)
|
|
$(call Device/UbiFit)
|
|
DEVICE_DTS := qcom-ipq4018-jalapeno
|
|
BLOCKSIZE := 128k
|
|
PAGESIZE := 2048
|
|
DEVICE_TITLE := 8devices Jalapeno
|
|
endef
|
|
TARGET_DEVICES += 8dev_jalapeno
|
|
|
|
define Device/asus_map-ac2200
|
|
$(call Device/FitImageLzma)
|
|
DEVICE_DTS := qcom-ipq4019-map-ac2200
|
|
DEVICE_TITLE := ASUS Lyra MAP-AC2200
|
|
IMAGES := sysupgrade.bin
|
|
DEVICE_PACKAGES := ipq-wifi-asus_map-ac2200 ath10k-firmware-qca9888-ct kmod-ath3k
|
|
endef
|
|
TARGET_DEVICES += asus_map-ac2200
|
|
|
|
define Device/asus_rt-ac58u
|
|
$(call Device/FitImageLzma)
|
|
DEVICE_DTS := qcom-ipq4018-rt-ac58u
|
|
BLOCKSIZE := 128k
|
|
PAGESIZE := 2048
|
|
DTB_SIZE := 65536
|
|
DEVICE_TITLE := Asus RT-AC58U
|
|
IMAGE_SIZE := 20439364
|
|
FILESYSTEMS := squashfs
|
|
# Someone - in their infinite wisdom - decided to put the firmware
|
|
# version in front of the image name \03\00\00\04 => Version 3.0.0.4
|
|
# Since u-boot works with strings we either need another fixup step
|
|
# to add a version... or we are very careful not to add '\0' into that
|
|
# string and call it a day.... Yeah, we do the latter!
|
|
UIMAGE_NAME:=$(shell echo -e '\03\01\01\01RT-AC58U')
|
|
IMAGES := sysupgrade.bin
|
|
DEVICE_PACKAGES := kmod-usb-ledtrig-usbport
|
|
endef
|
|
TARGET_DEVICES += asus_rt-ac58u
|
|
|
|
define Device/avm_fritzbox-4040
|
|
$(call Device/FitImageLzma)
|
|
DEVICE_DTS := qcom-ipq4018-fritz4040
|
|
BOARD_NAME := fritz4040
|
|
DEVICE_TITLE := AVM Fritz!Box 4040
|
|
IMAGE_SIZE := 29753344
|
|
UBOOT_PATH := $(STAGING_DIR_IMAGE)/uboot-fritz4040.bin
|
|
UBOOT_PARTITION_SIZE := 524288
|
|
IMAGES = eva.bin sysupgrade.bin
|
|
IMAGE/eva.bin := append-uboot | pad-to $$$$(UBOOT_PARTITION_SIZE) | append-kernel | append-rootfs | pad-rootfs
|
|
IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | append-metadata
|
|
DEVICE_PACKAGES := fritz-tffs fritz-caldata
|
|
endef
|
|
TARGET_DEVICES += avm_fritzbox-4040
|
|
|
|
define Device/compex_wpj428
|
|
$(call Device/FitImage)
|
|
DEVICE_DTS := qcom-ipq4028-wpj428
|
|
DEVICE_DTS_CONFIG := config@4
|
|
BLOCKSIZE := 64k
|
|
DEVICE_TITLE := Compex WPJ428
|
|
IMAGE_SIZE := 31232k
|
|
KERNEL_SIZE := 4096k
|
|
IMAGES = sysupgrade.bin
|
|
IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | append-metadata
|
|
DEVICE_PACKAGES := kmod-gpio-beeper
|
|
endef
|
|
TARGET_DEVICES += compex_wpj428
|
|
|
|
define Device/engenius_eap1300
|
|
$(call Device/FitImage)
|
|
DEVICE_TITLE := EnGenius EAP1300
|
|
DEVICE_DTS_CONFIG := config@4
|
|
BOARD_NAME := eap1300
|
|
DEVICE_DTS := qcom-ipq4018-eap1300
|
|
KERNEL_SIZE := 5120k
|
|
IMAGE_SIZE := 25344k
|
|
IMAGES := sysupgrade.bin
|
|
IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | append-metadata
|
|
DEVICE_PACKAGES := ipq-wifi-engenius_eap1300
|
|
endef
|
|
TARGET_DEVICES += engenius_eap1300
|
|
|
|
define Device/glinet_gl-b1300
|
|
$(call Device/FitImage)
|
|
DEVICE_TITLE := GL.iNet GL-B1300
|
|
BOARD_NAME := gl-b1300
|
|
DEVICE_DTS := qcom-ipq4029-gl-b1300
|
|
KERNEL_SIZE := 4096k
|
|
IMAGE_SIZE := 26624k
|
|
IMAGES := sysupgrade.bin
|
|
IMAGE/sysupgrade.bin := append-kernel |append-rootfs | pad-rootfs | append-metadata
|
|
endef
|
|
TARGET_DEVICES += glinet_gl-b1300
|
|
|
|
define Device/linksys_ea6350v3
|
|
# The Linksys EA6350v3 has a uboot bootloader that does not
|
|
# support either booting lzma kernel images nor booting UBI
|
|
# partitions. This uboot, however, supports raw kernel images and
|
|
# gzipped images.
|
|
#
|
|
# As for the time of writing this, the device will boot the kernel
|
|
# from a fixed address with a fixed length of 3MiB. Also, the
|
|
# device has a hard-coded kernel command line that requieres the
|
|
# rootfs and alt_rootfs to be in mtd11 and mtd13 respectively.
|
|
# Oh... and the kernel partition overlaps with the rootfs
|
|
# partition (the same for alt_kernel and alt_rootfs).
|
|
#
|
|
# If you are planing re-partitioning the device, you may want to
|
|
# keep those details in mind:
|
|
# 1. The kernel adresses you should honor are 0x00000000 and
|
|
# 0x02800000 respectively.
|
|
# 2. The kernel size (plus the dtb) cannot exceed 3.00MiB in size.
|
|
# 3. You can use 'zImage', but not a raw 'Image' packed with lzma.
|
|
# 4. The kernel command line from uboot is harcoded to boot with
|
|
# rootfs either in mtd11 or mtd13.
|
|
$(call Device/FitzImage)
|
|
DEVICE_TITLE := Linksys EA6350v3
|
|
DEVICE_DTS := qcom-ipq4018-ea6350v3
|
|
BLOCKSIZE := 128k
|
|
PAGESIZE := 2048
|
|
KERNEL_SIZE := 3145728
|
|
IMAGE_SIZE := 38797312
|
|
UBINIZE_OPTS := -E 5
|
|
IMAGES := factory.bin sysupgrade.bin
|
|
IMAGE/factory.bin := append-kernel | append-uImage-fakehdr filesystem | pad-to $$$${KERNEL_SIZE} | append-ubi | linksys-image type=EA6350v3
|
|
DEVICE_PACKAGES := ipq-wifi-linksys_ea6350v3 uboot-envtools
|
|
endef
|
|
TARGET_DEVICES += linksys_ea6350v3
|
|
|
|
define Device/meraki_mr33
|
|
$(call Device/FitImage)
|
|
DEVICE_DTS := qcom-ipq4029-mr33
|
|
BLOCKSIZE := 131072
|
|
PAGESIZE := 2048
|
|
DEVICE_TITLE := Cisco Meraki MR33
|
|
IMAGES = sysupgrade.bin
|
|
DEVICE_PACKAGES := -swconfig ath10k-firmware-qca9887-ct
|
|
endef
|
|
TARGET_DEVICES += meraki_mr33
|
|
|
|
define Device/netgear_ex61x0v2
|
|
$(call Device/DniImage)
|
|
DEVICE_DTS_CONFIG := config@4
|
|
NETGEAR_BOARD_ID := EX6150v2series
|
|
NETGEAR_HW_ID := 29765285+16+0+128+2x2
|
|
endef
|
|
|
|
define Device/netgear_ex6100v2
|
|
$(call Device/netgear_ex61x0v2)
|
|
DEVICE_DTS := qcom-ipq4018-ex6100v2
|
|
DEVICE_TITLE := Netgear EX6100v2
|
|
endef
|
|
TARGET_DEVICES += netgear_ex6100v2
|
|
|
|
define Device/netgear_ex6150v2
|
|
$(call Device/netgear_ex61x0v2)
|
|
DEVICE_DTS := qcom-ipq4018-ex6150v2
|
|
DEVICE_TITLE := Netgear EX6150v2
|
|
endef
|
|
TARGET_DEVICES += netgear_ex6150v2
|
|
|
|
define Device/openmesh_a42
|
|
$(call Device/FitImageLzma)
|
|
DEVICE_DTS := qcom-ipq4018-a42
|
|
DEVICE_DTS_CONFIG := config@om.a42
|
|
BLOCKSIZE := 64k
|
|
DEVICE_TITLE := OpenMesh A42
|
|
KERNEL = kernel-bin | lzma | fit lzma $$(DTS_DIR)/$$(DEVICE_DTS).dtb | pad-to $$(BLOCKSIZE)
|
|
IMAGE_SIZE := 15616k
|
|
IMAGES = factory.bin sysupgrade.bin
|
|
IMAGE/factory.bin := append-rootfs | pad-rootfs | openmesh-image ce_type=A42
|
|
IMAGE/sysupgrade.bin/squashfs := append-rootfs | pad-rootfs | sysupgrade-tar rootfs=$$$$@ | append-metadata
|
|
DEVICE_PACKAGES := uboot-envtools
|
|
endef
|
|
TARGET_DEVICES += openmesh_a42
|
|
|
|
define Device/openmesh_a62
|
|
$(call Device/FitImageLzma)
|
|
DEVICE_DTS := qcom-ipq4019-a62
|
|
DEVICE_DTS_CONFIG := config@om.a62
|
|
BLOCKSIZE := 64k
|
|
DEVICE_TITLE := OpenMesh A62
|
|
KERNEL = kernel-bin | lzma | fit lzma $$(DTS_DIR)/$$(DEVICE_DTS).dtb | pad-to $$(BLOCKSIZE)
|
|
IMAGE_SIZE := 15552k
|
|
IMAGES = factory.bin sysupgrade.bin
|
|
IMAGE/factory.bin := append-rootfs | pad-rootfs | openmesh-image ce_type=A62
|
|
IMAGE/sysupgrade.bin/squashfs := append-rootfs | pad-rootfs | sysupgrade-tar rootfs=$$$$@ | append-metadata
|
|
DEVICE_PACKAGES := ath10k-firmware-qca9888-ct uboot-envtools
|
|
endef
|
|
|
|
TARGET_DEVICES += openmesh_a62
|
|
|
|
define Device/qcom_ap-dk01.1-c1
|
|
DEVICE_TITLE := QCA AP-DK01.1-C1
|
|
BOARD_NAME := ap-dk01.1-c1
|
|
DEVICE_DTS := qcom-ipq4019-ap.dk01.1-c1
|
|
KERNEL_INSTALL := 1
|
|
KERNEL_SIZE := 4096k
|
|
IMAGE_SIZE := 26624k
|
|
$(call Device/FitImage)
|
|
IMAGES := sysupgrade.bin
|
|
IMAGE/sysupgrade.bin := append-kernel | pad-to $$$${KERNEL_SIZE} | append-rootfs | pad-rootfs | append-metadata
|
|
endef
|
|
TARGET_DEVICES += qcom_ap-dk01.1-c1
|
|
|
|
define Device/qcom_ap-dk04.1-c1
|
|
$(call Device/FitImage)
|
|
$(call Device/UbiFit)
|
|
DEVICE_DTS := qcom-ipq4019-ap.dk04.1-c1
|
|
KERNEL_INSTALL := 1
|
|
KERNEL_SIZE := 4048k
|
|
BLOCKSIZE := 128k
|
|
PAGESIZE := 2048
|
|
BOARD_NAME := ap-dk04.1-c1
|
|
DEVICE_TITLE := QCA AP-DK04.1-C1
|
|
endef
|
|
TARGET_DEVICES += qcom_ap-dk04.1-c1
|
|
|
|
define Device/zyxel_nbg6617
|
|
$(call Device/FitImageLzma)
|
|
DEVICE_DTS := qcom-ipq4018-nbg6617
|
|
DEVICE_TITLE := ZyXEL NBG6617
|
|
ROOTFS_SIZE := 24960k
|
|
RAS_BOARD := NBG6617
|
|
RAS_ROOTFS_SIZE := 19840k
|
|
RAS_VERSION := "$(VERSION_DIST) $(REVISION)"
|
|
IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | append-metadata
|
|
IMAGES := sysupgrade.bin factory.bin
|
|
# The ZyXEL firmware allows flashing thru the web-gui only when the rootfs is
|
|
# at least as large as the one of the initial firmware image (not the current
|
|
# one on the device). This only applies to the Web-UI, the bootlaoder ignores
|
|
# this minimum-size. However, the larger image can be flashed both ways.
|
|
IMAGE/factory.bin := append-rootfs | pad-rootfs | pad-to 64k | check-size $$$$(ROOTFS_SIZE) | zyxel-ras-image separate-kernel
|
|
IMAGE/sysupgrade.bin/squashfs := append-rootfs | pad-rootfs | check-size $$$$(ROOTFS_SIZE) | sysupgrade-tar rootfs=$$$$@ | append-metadata
|
|
DEVICE_PACKAGES := uboot-envtools kmod-usb-ledtrig-usbport
|
|
endef
|
|
TARGET_DEVICES += zyxel_nbg6617
|
|
|
|
define Device/zyxel_wre6606
|
|
$(call Device/FitImage)
|
|
DEVICE_TITLE := ZyXEL WRE6606
|
|
DEVICE_DTS_CONFIG := config@4
|
|
DEVICE_DTS := qcom-ipq4018-wre6606
|
|
IMAGES := sysupgrade.bin
|
|
IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | append-metadata
|
|
endef
|
|
TARGET_DEVICES += zyxel_wre6606
|
|
|
|
$(eval $(call BuildImage))
|