mirror of
https://github.com/openwrt/openwrt.git
synced 2024-12-27 01:11:14 +00:00
ec85e48a11
On MikroTik RB91x board series a reset key shares SoC gpio line #15 with NAND ALE and NAND IO7. So we need a custom gpio driver to manage this non-trivial connection schema. Also rb91x-nand needs to have an ability to disable a polling of the key while it works with NAND. While we've been integrating rb91x-key into a firmware, we've figured out that: * In the gpio-latch driver we need to add a "cansleep" suffix to several gpiolib calls, * When gpio-latch and rb91x-nand fail to get a gpio and an error is -EPROBE_DEFER, they shouldn't report about this, since this actually is not an error and occurs when the gpio-latch probe function is called before the rb91x-key probe. We fix these related things here too. Signed-off-by: Denis Kalashnikov <denis281089@gmail.com> Reviewed-by: Sergey Ryazanov <ryazanov.s.a@gmail.com> Tested-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
69 lines
2.4 KiB
Diff
69 lines
2.4 KiB
Diff
--- a/drivers/gpio/Kconfig
|
|
+++ b/drivers/gpio/Kconfig
|
|
@@ -341,6 +341,13 @@ config GPIO_IXP4XX
|
|
IXP4xx series of chips.
|
|
|
|
If unsure, say N.
|
|
+
|
|
+config GPIO_LATCH
|
|
+ tristate "MikroTik RouterBOARD GPIO latch support"
|
|
+ depends on ATH79
|
|
+ help
|
|
+ GPIO driver for latch on some MikroTik RouterBOARDs.
|
|
+
|
|
config GPIO_LOGICVC
|
|
tristate "Xylon LogiCVC GPIO support"
|
|
depends on MFD_SYSCON && OF
|
|
@@ -495,6 +502,10 @@ config GPIO_REG
|
|
A 32-bit single register GPIO fixed in/out implementation. This
|
|
can be used to represent any register as a set of GPIO signals.
|
|
|
|
+config GPIO_RB91X_KEY
|
|
+ tristate "MikroTik RB91x board series reset key support"
|
|
+ depends on ATH79
|
|
+
|
|
config GPIO_SAMA5D2_PIOBU
|
|
tristate "SAMA5D2 PIOBU GPIO support"
|
|
depends on MFD_SYSCON
|
|
--- a/drivers/gpio/Makefile
|
|
+++ b/drivers/gpio/Makefile
|
|
@@ -72,6 +72,7 @@ obj-$(CONFIG_GPIO_IT87) += gpio-it87.o
|
|
obj-$(CONFIG_GPIO_IXP4XX) += gpio-ixp4xx.o
|
|
obj-$(CONFIG_GPIO_JANZ_TTL) += gpio-janz-ttl.o
|
|
obj-$(CONFIG_GPIO_KEMPLD) += gpio-kempld.o
|
|
+obj-$(CONFIG_GPIO_LATCH) += gpio-latch.o
|
|
obj-$(CONFIG_GPIO_LOGICVC) += gpio-logicvc.o
|
|
obj-$(CONFIG_GPIO_LOONGSON1) += gpio-loongson1.o
|
|
obj-$(CONFIG_GPIO_LOONGSON) += gpio-loongson.o
|
|
@@ -121,6 +122,7 @@ obj-$(CONFIG_GPIO_PMIC_EIC_SPRD) += gpio
|
|
obj-$(CONFIG_GPIO_PXA) += gpio-pxa.o
|
|
obj-$(CONFIG_GPIO_RASPBERRYPI_EXP) += gpio-raspberrypi-exp.o
|
|
obj-$(CONFIG_GPIO_RB4XX) += gpio-rb4xx.o
|
|
+obj-$(CONFIG_GPIO_RB91X_KEY) += gpio-rb91x-key.o
|
|
obj-$(CONFIG_GPIO_RC5T583) += gpio-rc5t583.o
|
|
obj-$(CONFIG_GPIO_RCAR) += gpio-rcar.o
|
|
obj-$(CONFIG_GPIO_RDA) += gpio-rda.o
|
|
--- a/drivers/mtd/nand/raw/Kconfig
|
|
+++ b/drivers/mtd/nand/raw/Kconfig
|
|
@@ -571,4 +571,10 @@ config MTD_NAND_RB4XX
|
|
Enables support for the NAND flash chip on Mikrotik Routerboard
|
|
RB4xx series.
|
|
|
|
+config MTD_NAND_RB91X
|
|
+ tristate "MikroTik RB91x NAND driver support"
|
|
+ depends on ATH79 && MTD_RAW_NAND
|
|
+ help
|
|
+ Enables support for the NAND flash chip on MikroTik RB91x series.
|
|
+
|
|
endif # MTD_RAW_NAND
|
|
--- a/drivers/mtd/nand/raw/Makefile
|
|
+++ b/drivers/mtd/nand/raw/Makefile
|
|
@@ -60,6 +60,7 @@ obj-$(CONFIG_MTD_NAND_CADENCE) += caden
|
|
obj-$(CONFIG_MTD_NAND_ARASAN) += arasan-nand-controller.o
|
|
obj-$(CONFIG_MTD_NAND_AR934X) += ar934x_nand.o
|
|
obj-$(CONFIG_MTD_NAND_RB4XX) += nand_rb4xx.o
|
|
+obj-$(CONFIG_MTD_NAND_RB91X) += rb91x_nand.o
|
|
|
|
nand-objs := nand_base.o nand_legacy.o nand_bbt.o nand_timings.o nand_ids.o
|
|
nand-objs += nand_onfi.o
|