openwrt/target/linux/ramips/dts/mt7621_tplink_archer-ax23-v1.dts
David Bauer 7dceef5ee5 ramips: add support for TP-Link Archer AX23 v1
Hardware
--------
CPU:    MediaTek MT7621 DAT
RAM:    128MB DDR3 (integrated)
FLASH:  16MB SPI-NOR ()
WiFi:   MediaTek MT7905 + MT7975 (2.4 / 5 DBDC) 802.11ax
SERIAL: 115200 8N1
        LEDs - (3V3 - GND - RX - TX) - ETH ports

Installation
------------

Upload the factory image using the Web-UI.

Web-Recovery
------------

The router supports a HTTP recovery mode by holding the reset-button
when powering on. The interface is reachable at 192.168.0.1 and supports
installation using the factory image.

Signed-off-by: David Bauer <mail@david-bauer.net>
2023-03-15 01:44:29 +01:00

204 lines
3.1 KiB
Plaintext

// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
#include "mt7621.dtsi"
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>
/ {
compatible = "tplink,archer-ax23-v1", "mediatek,mt7621-soc";
model = "TP-Link Archer AX23 v1";
aliases {
led-boot = &led_power;
led-failsafe = &led_power;
led-running = &led_power;
led-upgrade = &led_power;
label-mac-device = &gmac0;
};
chosen {
bootargs = "console=ttyS0,115200";
};
keys {
compatible = "gpio-keys";
reset {
label = "reset";
gpios = <&gpio 8 GPIO_ACTIVE_LOW>;
linux,code = <KEY_RESTART>;
};
wps {
label = "rfkill";
gpios = <&gpio 7 GPIO_ACTIVE_LOW>;
linux,code = <KEY_RFKILL>;
};
};
leds {
compatible = "gpio-leds";
led_power: power {
label = "green:power";
gpios = <&gpio 18 GPIO_ACTIVE_LOW>;
};
wifi2g {
label = "green:wifi2g";
gpios = <&gpio 16 GPIO_ACTIVE_LOW>;
linux,default-trigger = "phy0tpt";
};
wifi5g {
label = "green:wifi5g";
gpios = <&gpio 15 GPIO_ACTIVE_LOW>;
linux,default-trigger = "phy1tpt";
};
wan-green {
label = "green:wan";
gpios = <&gpio 14 GPIO_ACTIVE_LOW>;
};
wan-orange {
label = "orange:wan";
gpios = <&gpio 13 GPIO_ACTIVE_LOW>;
};
lan {
label = "green:lan";
gpios = <&gpio 4 GPIO_ACTIVE_LOW>;
};
wps {
label = "green:wps";
gpios = <&gpio 3 GPIO_ACTIVE_LOW>;
};
};
};
&spi0 {
status = "okay";
flash@0 {
compatible = "jedec,spi-nor";
reg = <0>;
spi-max-frequency = <80000000>;
partitions {
compatible = "fixed-partitions";
#address-cells = <1>;
#size-cells = <1>;
partition@0 {
label = "u-boot";
reg = <0x000000 0x040000>;
read-only;
};
partition@40000 {
compatible = "denx,uimage";
label = "firmware";
reg = <0x040000 0xf60000>;
};
config: partition@fa0000 {
label = "config";
reg = <0xfa0000 0x010000>;
read-only;
};
partition@fb0000 {
label = "tplink";
reg = <0xfb0000 0x040000>;
read-only;
};
radio: partition@ff0000 {
label = "radio";
reg = <0xff0000 0x010000>;
read-only;
};
};
};
};
&pcie {
status = "okay";
};
&pcie1 {
wifi@0,0 {
compatible = "mediatek,mt76";
reg = <0x0000 0 0 0 0>;
mediatek,mtd-eeprom = <&radio 0x0>;
nvmem-cells = <&macaddr_config_8>;
nvmem-cell-names = "mac-address";
mediatek,disable-radar-background;
};
};
&gmac0 {
nvmem-cells = <&macaddr_config_8>;
nvmem-cell-names = "mac-address";
};
&gmac1 {
status = "okay";
label = "wan";
phy-handle = <&ethphy4>;
nvmem-cells = <&macaddr_config_8>;
nvmem-cell-names = "mac-address";
mac-address-increment = <1>;
};
&mdio {
ethphy4: ethernet-phy@4 {
reg = <4>;
};
};
&switch0 {
ports {
port@0 {
status = "okay";
label = "lan1";
};
port@1 {
status = "okay";
label = "lan2";
};
port@2 {
status = "okay";
label = "lan3";
};
port@3 {
status = "okay";
label = "lan4";
};
};
};
&state_default {
gpio {
groups = "i2c", "uart3", "jtag", "wdt";
function = "gpio";
};
};
&config {
compatible = "nvmem-cells";
#address-cells = <1>;
#size-cells = <1>;
macaddr_config_8: macaddr@8 {
reg = <0x8 0x6>;
};
};