mirror of
https://github.com/openwrt/openwrt.git
synced 2024-12-20 14:13:16 +00:00
9371542783
This adds support for the Intel Falcon SoC for GPON.
Support for the Falcon SoC was removed in commit c821836395 svn rev:
40392 from OpenWrt, this commit adds it again.
This patch adds a new subtarget for the Falcon SoC, but it still misses
all the drivers needed to control the GPON part.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
115 lines
2.1 KiB
Plaintext
115 lines
2.1 KiB
Plaintext
|
|
#include <dt-bindings/interrupt-controller/irq.h>
|
|
#include <dt-bindings/gpio/gpio.h>
|
|
|
|
/ {
|
|
compatible = "lantiq,falcon-easy98000", "lantiq,falcon";
|
|
|
|
chosen {
|
|
bootargs-append = "console=ttyLTQ0,115200 init=/etc/preinit";
|
|
};
|
|
|
|
memory@0 {
|
|
device_type = "memory";
|
|
reg = <0x0 0x4000000>;
|
|
};
|
|
|
|
easy98000-leds {
|
|
compatible = "gpio-leds";
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&bootled_pins>;
|
|
|
|
LED_0 {
|
|
label = "easy98000:green:gpon";
|
|
gpios = <&gpio0 9 GPIO_ACTIVE_HIGH>;
|
|
default-state = "keep";
|
|
};
|
|
LED_1 {
|
|
label = "easy98000:red:gpon";
|
|
gpios = <&gpio0 10 GPIO_ACTIVE_HIGH>;
|
|
default-state = "keep";
|
|
};
|
|
LED_2 {
|
|
label = "easy98000:green:gpon_tx";
|
|
gpios = <&gpio0 11 GPIO_ACTIVE_HIGH>;
|
|
default-state = "keep";
|
|
};
|
|
LED_3 {
|
|
label = "easy98000:green:gpon_rx";
|
|
gpios = <&gpio0 12 GPIO_ACTIVE_HIGH>;
|
|
default-state = "keep";
|
|
};
|
|
LED_4 {
|
|
label = "easy98000:green:voice";
|
|
gpios = <&gpio0 13 GPIO_ACTIVE_HIGH>;
|
|
default-state = "keep";
|
|
};
|
|
LED_5 {
|
|
label = "easy98000:green:status";
|
|
gpios = <&gpio0 14 GPIO_ACTIVE_HIGH>;
|
|
default-state = "keep";
|
|
};
|
|
};
|
|
};
|
|
|
|
&ebu_cs1 {
|
|
eth0: ethernet@0000000 {
|
|
compatible = "davicom,dm9000";
|
|
device_type = "network";
|
|
reg = <0x0000003 0x1>, <0x0000001 0x1>;
|
|
reg-names = "addr", "data";
|
|
interrupt-parent = <&gpio1>;
|
|
#interrupt-cells = <2>;
|
|
interrupts = <10 IRQ_TYPE_LEVEL_LOW>;
|
|
local-mac-address = [ 00 00 00 00 00 00 ];
|
|
};
|
|
|
|
cpld@3c00000 {
|
|
compatible = "lantiq,easy98000_addon";
|
|
reg = <0x3c00000 0x2>;
|
|
};
|
|
|
|
cpld@3c0000c {
|
|
compatible = "lantiq,easy98000_cpld_led";
|
|
reg = <0x3c0000c 0x2>, <0x3c00012 0x2>;
|
|
};
|
|
};
|
|
|
|
/* // enable this for second uart:
|
|
&serial1 {
|
|
status = "okay";
|
|
};*/
|
|
|
|
&spi {
|
|
status = "okay";
|
|
|
|
eeprom@1 {
|
|
compatible = "atmel,at25", "atmel,at25160n";
|
|
reg = <2>;
|
|
spi-max-frequency = <1000000>;
|
|
spi-cpha;
|
|
spi-cpol;
|
|
|
|
pagesize = <32>;
|
|
size = <2048>;
|
|
address-width = <16>;
|
|
};
|
|
};
|
|
|
|
&i2c {
|
|
status = "okay";
|
|
|
|
clock-frequency = <100000>;
|
|
|
|
/* eeprom-emulation by OMU */
|
|
eeprom@50 {
|
|
compatible = "at,24c02";
|
|
reg = <0x50>;
|
|
};
|
|
eeprom@51 {
|
|
compatible = "at,24c02";
|
|
reg = <0x51>;
|
|
};
|
|
};
|
|
|