mirror of
https://github.com/openwrt/openwrt.git
synced 2024-12-30 02:29:01 +00:00
57cb387cfe
JCG Q20 is an AX 1800M router. Hardware specs: SoC: MediaTek MT7621AT Flash: Winbond W29N01HV 128 MiB RAM: Winbond W632GU6NB-11 256 MiB WiFi: MT7915 2.4/5 GHz 2T2R Ethernet: 10/100/1000 Mbps x3 LED: Status (red / blue) Button: Reset, WPS Power: DC 12V,1A Flash instructions: Upload factory.bin in stock firmware's upgrade page, do not preserve settings. MAC addresses map: 0x00004 *:3e wlan2g/wlan5g 0x3fff4 *:3c lan/label 0x3fffa *:3c wan Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
176 lines
2.7 KiB
Plaintext
176 lines
2.7 KiB
Plaintext
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
|
|
|
#include "mt7621.dtsi"
|
|
|
|
#include <dt-bindings/gpio/gpio.h>
|
|
#include <dt-bindings/input/input.h>
|
|
|
|
/ {
|
|
compatible = "jcg,q20", "mediatek,mt7621-soc";
|
|
model = "JCG Q20";
|
|
|
|
aliases {
|
|
led-boot = &led_status_red;
|
|
led-failsafe = &led_status_red;
|
|
led-running = &led_status_blue;
|
|
led-upgrade = &led_status_blue;
|
|
label-mac-device = &gmac0;
|
|
};
|
|
|
|
chosen {
|
|
bootargs = "console=ttyS0,115200";
|
|
};
|
|
|
|
leds {
|
|
compatible = "gpio-leds";
|
|
|
|
led_status_red: status_red {
|
|
label = "red:status";
|
|
gpios = <&gpio 14 GPIO_ACTIVE_HIGH>;
|
|
};
|
|
|
|
led_status_blue: status_blue {
|
|
label = "blue:status";
|
|
gpios = <&gpio 15 GPIO_ACTIVE_LOW>;
|
|
};
|
|
};
|
|
|
|
keys {
|
|
compatible = "gpio-keys";
|
|
|
|
reset {
|
|
label = "reset";
|
|
gpios = <&gpio 18 GPIO_ACTIVE_LOW>;
|
|
linux,code = <KEY_RESTART>;
|
|
};
|
|
|
|
wps {
|
|
label = "wps";
|
|
gpios = <&gpio 16 GPIO_ACTIVE_LOW>;
|
|
linux,code = <KEY_WPS_BUTTON>;
|
|
};
|
|
};
|
|
|
|
ubi-concat {
|
|
compatible = "mtd-concat";
|
|
devices = <&ubiconcat0 &ubiconcat1>;
|
|
|
|
partitions {
|
|
compatible = "fixed-partitions";
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
|
|
partition@0 {
|
|
label = "ubi";
|
|
reg = <0x0 0x5900000>;
|
|
};
|
|
};
|
|
};
|
|
};
|
|
|
|
&nand {
|
|
status = "okay";
|
|
|
|
partitions {
|
|
compatible = "fixed-partitions";
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
|
|
partition@0 {
|
|
label = "Bootloader";
|
|
reg = <0x0 0x80000>;
|
|
read-only;
|
|
};
|
|
|
|
partition@80000 {
|
|
label = "Config";
|
|
reg = <0x80000 0x80000>;
|
|
};
|
|
|
|
factory: partition@100000 {
|
|
label = "Factory";
|
|
reg = <0x100000 0x80000>;
|
|
read-only;
|
|
};
|
|
|
|
partition@180000 {
|
|
label = "kernel";
|
|
reg = <0x180000 0x400000>;
|
|
};
|
|
|
|
ubiconcat0: partition@580000 {
|
|
label = "ubiconcat0";
|
|
reg = <0x580000 0x1c00000>;
|
|
};
|
|
|
|
partition@2180000 {
|
|
label = "firmware_backup";
|
|
reg = <0x2180000 0x2000000>;
|
|
};
|
|
|
|
partition@4180000 {
|
|
label = "rootfs_data_back";
|
|
reg = <0x4180000 0x80000>;
|
|
read-only;
|
|
};
|
|
|
|
partition@4200000 {
|
|
label = "nvram_config";
|
|
reg = <0x4200000 0x80000>;
|
|
read-only;
|
|
};
|
|
|
|
ubiconcat1: partition@4280000 {
|
|
label = "ubiconcat1";
|
|
reg = <0x4280000 0x3d00000>;
|
|
};
|
|
|
|
/*
|
|
* last 512 KiB are for the bad block table
|
|
*/
|
|
};
|
|
};
|
|
|
|
&pcie {
|
|
status = "okay";
|
|
};
|
|
|
|
&pcie1 {
|
|
wifi@0,0 {
|
|
compatible = "mediatek,mt76";
|
|
reg = <0x0000 0 0 0 0>;
|
|
mediatek,mtd-eeprom = <&factory 0x0>;
|
|
};
|
|
};
|
|
|
|
&gmac0 {
|
|
mtd-mac-address = <&factory 0x3fff4>;
|
|
};
|
|
|
|
&switch0 {
|
|
ports {
|
|
port@0 {
|
|
status = "okay";
|
|
label = "wan";
|
|
mtd-mac-address = <&factory 0x3fffa>;
|
|
};
|
|
|
|
port@1 {
|
|
status = "okay";
|
|
label = "lan1";
|
|
};
|
|
|
|
port@4 {
|
|
status = "okay";
|
|
label = "lan2";
|
|
};
|
|
};
|
|
};
|
|
|
|
&state_default {
|
|
gpio {
|
|
groups = "jtag", "wdt";
|
|
function = "gpio";
|
|
};
|
|
};
|