mirror of
https://github.com/openwrt/openwrt.git
synced 2025-02-12 05:35:38 +00:00
eae5e55a79
setup.c unconditionally sets the sys-led mode (blinking rate) to a permanent high output. This may cause issues when a board expects this pin to toggle periodically, e.g. when hooked up to an external watchdog. If the sys-led peripheral is used to control an LED, the mux should be configured to use the pin as GPIO0, allowing for better control as a GPIO LED. Signed-off-by: Sander Vanheule <sander@svanheule.net>
77 lines
1.5 KiB
C
77 lines
1.5 KiB
C
// SPDX-License-Identifier: GPL-2.0-only
|
|
/*
|
|
* Setup for the Realtek RTL838X SoC:
|
|
* Memory, Timer and Serial
|
|
*
|
|
* Copyright (C) 2020 B. Koblitz
|
|
* based on the original BSP by
|
|
* Copyright (C) 2006-2012 Tony Wu (tonywu@realtek.com)
|
|
*
|
|
*/
|
|
|
|
#include <linux/console.h>
|
|
#include <linux/init.h>
|
|
#include <linux/clkdev.h>
|
|
#include <linux/clk-provider.h>
|
|
#include <linux/delay.h>
|
|
#include <linux/of_fdt.h>
|
|
#include <linux/irqchip.h>
|
|
|
|
#include <asm/addrspace.h>
|
|
#include <asm/io.h>
|
|
#include <asm/bootinfo.h>
|
|
#include <asm/time.h>
|
|
#include <asm/prom.h>
|
|
#include <asm/smp-ops.h>
|
|
|
|
#include "mach-rtl83xx.h"
|
|
|
|
extern struct rtl83xx_soc_info soc_info;
|
|
|
|
void __init plat_mem_setup(void)
|
|
{
|
|
void *dtb;
|
|
|
|
set_io_port_base(KSEG1);
|
|
|
|
if (fw_passed_dtb) /* UHI interface */
|
|
dtb = (void *)fw_passed_dtb;
|
|
else if (&__dtb_start[0] != &__dtb_end[0])
|
|
dtb = (void *)__dtb_start;
|
|
else
|
|
panic("no dtb found");
|
|
|
|
/*
|
|
* Load the devicetree. This causes the chosen node to be
|
|
* parsed resulting in our memory appearing
|
|
*/
|
|
__dt_setup_arch(dtb);
|
|
}
|
|
|
|
void __init plat_time_init(void)
|
|
{
|
|
struct device_node *np;
|
|
u32 freq = 500000000;
|
|
|
|
of_clk_init(NULL);
|
|
timer_probe();
|
|
|
|
np = of_find_node_by_name(NULL, "cpus");
|
|
if (!np) {
|
|
pr_err("Missing 'cpus' DT node, using default frequency.");
|
|
} else {
|
|
if (of_property_read_u32(np, "frequency", &freq) < 0)
|
|
pr_err("No 'frequency' property in DT, using default.");
|
|
else
|
|
pr_info("CPU frequency from device tree: %dMHz", freq / 1000000);
|
|
of_node_put(np);
|
|
}
|
|
|
|
mips_hpt_frequency = freq / 2;
|
|
}
|
|
|
|
void __init arch_init_irq(void)
|
|
{
|
|
irqchip_init();
|
|
}
|