ExternalVendorCode/openwrt
1
0
Fork 0
mirror of https://github.com/openwrt/openwrt.git synced 2024-12-29 10:08:59 +00:00
Code Issues Actions 6 Packages Projects Releases Wiki Activity
7402cc7160
openwrt/package/boot/uboot-kirkwood/patches/008-nsa325-uboot-generic.patch
Alberto Bursi e13d9cd07f uboot-kirkwood: fix malformed boot configuration 
With current uboot default configuration the bootloader will
fail to start the OpenWrt firmware with the following error:
-----
unexpected character 'b' at the end of partition
Error initializing mtdparts!
incorrect device type in ubi
Partition ubi not found!
Error, no UBI device/partition selected!
Wrong Image Format for bootm command
Error occured, error code = 112
-----

If the uboot configuration is examined with printenv
I can see that mdtparts line (on a nsa310) is wrong:
-----
mtdparts=mtdparts=orion_nand:0x0c0000(uboot),
0x80000(uboot_env),0x7ec0000(ubi)bootargs_root=
----

The "bootargs_root=" that was appended to it should not be there.

Fix the issue by adding a \0 line terminator at the end of affected lines,
mimicking what is also done by uboot upstream.

This issue was detected and confirmed on a nsa310, nsa325 and
a pogoplug v4, but it's not hardware-specific, so apply the same fix
to other devices as well.

Note that the issue is with the uboot's integrated boot configuration,
which is not used unless the uboot configuration in flash is unavailable
(erased or corrupted), which happens only on first time installation,
or if the user deletes the uboot configuration when upgrading uboot.
People just upgrading from an older uboot without erasing their previous
uboot configuration stored in flash would not have noticed this issue.

Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>
2018-06-27 08:42:54 +02:00

654 lines
19 KiB
Diff
Raw Blame History

--- a/arch/arm/mach-kirkwood/Kconfig
+++ b/arch/arm/mach-kirkwood/Kconfig
@@ -62,6 +62,9 @@ config TARGET_NSA310
config TARGET_NSA310S
bool "Zyxel NSA310S"
+config TARGET_NSA325
+ bool "Zyxel NSA325 board"
+
endchoice
config SYS_SOC
@@ -85,5 +88,6 @@ source "board/Seagate/goflexhome/Kconfig
source "board/Seagate/nas220/Kconfig"
source "board/zyxel/nsa310/Kconfig"
source "board/zyxel/nsa310s/Kconfig"
+source "board/zyxel/nsa325/Kconfig"
endif
--- /dev/null
+++ b/board/zyxel/nsa325/Kconfig
@@ -0,0 +1,12 @@
+if TARGET_NSA325
+
+config SYS_BOARD
+ default "nsa325"
+
+config SYS_VENDOR
+ default "zyxel"
+
+config SYS_CONFIG_NAME
+ default "nsa325"
+
+endif
--- /dev/null
+++ b/board/zyxel/nsa325/MAINTAINERS
@@ -0,0 +1,6 @@
+NSA325 BOARD
+M: Alberto Bursi <alberto.bursi@outlook.it>
+S: Maintained
+F: board/zyxel/nsa325/
+F: include/configs/nsa325.h
+F: configs/nsa325_defconfig
--- /dev/null
+++ b/board/zyxel/nsa325/Makefile
@@ -0,0 +1,13 @@
+#
+# (C) Copyright 2015 bodhi <mibodhi@gmail.com>
+#
+# Based on
+# (C) Copyright 2009
+# Marvell Semiconductor <www.marvell.com>
+# Written-by: Prafulla Wadaskar <prafulla@marvell.com>
+#
+# SPDX-License-Identifier: GPL-2.0+
+#
+
+obj-y := nsa325.o
+
--- /dev/null
+++ b/board/zyxel/nsa325/kwbimage.cfg
@@ -0,0 +1,78 @@
+# Copyright (C) 2015 bodhi <mibodhi@gmail.com>
+#
+# Extracted from Zyxel GPL source for u-boot-1.1.4_NSA325v2
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
+# MA 02110-1301 USA
+#
+# Refer docs/README.kwimage for more details about how-to configure
+# and create kirkwood boot image
+#
+
+# Boot Media configurations
+#BOOT_FROM uart
+BOOT_FROM nand
+NAND_ECC_MODE default
+NAND_PAGE_SIZE 0x0800
+
+# SOC registers configuration using bootrom header extension
+# Maximum KWBIMAGE_MAX_CONFIG configurations allowed
+
+# Configure RGMII-0 interface pad voltage to 1.8V
+DATA 0xFFD100e0 0x1b1b1b9b
+
+#Dram initalization
+DATA 0xFFD01400 0x4301503E # DDR Configuration register
+DATA 0xFFD01404 0xB9843000 # DDR Controller Control Low
+DATA 0xFFD01408 0x33137777 # DDR Timing (Low)
+DATA 0xFFD0140C 0x16000C55 # DDR Timing (High)
+DATA 0xFFD01410 0x04000000 # DDR Address Control
+DATA 0xFFD01414 0x00000000 # DDR Open Pages Control
+DATA 0xFFD01418 0x00000000 # DDR Operation
+DATA 0xFFD0141C 0x00000672 # DDR Mode
+DATA 0xFFD01420 0x00000004 # DDR Extended Mode
+DATA 0xFFD01424 0x0000F14F # DDR Controller Control High
+DATA 0xFFD01428 0x000D6720 # DDR3 ODT Read Timing
+DATA 0xFFD0147C 0x0000B571 # DDR2 ODT Write Timing
+DATA 0xFFD01504 0x1FFFFFF1 # CS[0]n Size
+DATA 0xFFD01508 0x20000000 # CS[1]n Base address to 512Mb
+DATA 0xFFD0150C 0x1FFFFFF4 # CS[1]n Size 512Mb Window enabled for CS1
+DATA 0xFFD01514 0x00000000 # CS[2]n Size, window disabled
+DATA 0xFFD0151C 0x00000000 # CS[3]n Size, window disabled
+DATA 0xFFD01494 0x00120000 # DDR ODT Control (Low)
+DATA 0xFFD01498 0x00000000 # DDR ODT Control (High)
+DATA 0xFFD0149C 0x0000E803 # CPU ODT Control
+
+DATA 0xFFD015D0 0x00000630
+DATA 0xFFD015D4 0x00000046
+DATA 0xFFD015D8 0x00000008
+DATA 0xFFD015DC 0x00000000
+DATA 0xFFD015E0 0x00000023
+DATA 0xFFD015E4 0x00203C18
+DATA 0xFFD01620 0x00384800
+DATA 0xFFD01480 0x00000001
+DATA 0xFFD20134 0x66666666
+DATA 0xFFD20138 0x00066666
+
+#Disable nsa325 hardware watchdog to allow successful kwbooting
+DATA 0xFFD10100 0x00004000 # set GPIO 14 to high to disable the watchdog
+DATA 0xFFD10104 0xFFFFBFFF # set GPIO 14 to output (to block any other input to it)
+
+# End of Header extension
+DATA 0x0 0x0
+
--- /dev/null
+++ b/board/zyxel/nsa325/nsa325.c
@@ -0,0 +1,265 @@
+/*
+ * Copyright (C) 2015 bodhi <mibodhi@gmail.com>
+ *
+ * Based on
+ * Copyright (C) 2014 Jason Plum <jplum@archlinuxarm.org>
+ *
+ * Based on nsa320.c originall written by
+ * Copyright (C) 2012 Peter Schildmann <linux@schildmann.info>
+ *
+ * Based on guruplug.c originally written by
+ * Siddarth Gore <gores@marvell.com>
+ * (C) Copyright 2009
+ * Marvell Semiconductor <www.marvell.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
+ * MA 02110-1301 USA
+ */
+
+#include <common.h>
+#include <miiphy.h>
+#include <asm/arch/soc.h>
+#include <asm/arch/mpp.h>
+#include <asm/arch/cpu.h>
+#include <asm/gpio.h>
+#include <asm/io.h>
+#include "nsa325.h"
+#include <asm/arch/gpio.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+int board_early_init_f(void)
+{
+ /*
+ * default gpio configuration
+ * There are maximum 64 gpios controlled through 2 sets of registers
+ * the below configuration configures mainly initial LED status
+ */
+ mvebu_config_gpio(NSA325_VAL_LOW, NSA325_VAL_HIGH,
+ NSA325_OE_LOW, NSA325_OE_HIGH);
+
+ /* Multi-Purpose Pins Functionality configuration */
+ /* (all LEDs & power off active high) */
+ u32 kwmpp_config[] = {
+ MPP0_NF_IO2,
+ MPP1_NF_IO3,
+ MPP2_NF_IO4,
+ MPP3_NF_IO5,
+ MPP4_NF_IO6,
+ MPP5_NF_IO7,
+ MPP6_SYSRST_OUTn,
+ MPP7_GPO,
+ MPP8_TW_SDA, /* PCF8563 RTC chip */
+ MPP9_TW_SCK, /* connected to TWSI */
+ MPP10_UART0_TXD,
+ MPP11_UART0_RXD,
+ MPP12_GPO, /* HDD2 LED (green) */
+ MPP13_GPIO, /* HDD2 LED (red) */
+ MPP14_GPIO, /* MCU DATA pin (in) */
+ MPP15_GPIO, /* USB LED (green) */
+ MPP16_GPIO, /* MCU CLK pin (out) */
+ MPP17_GPIO, /* MCU ACT pin (out) */
+ MPP18_NF_IO0,
+ MPP19_NF_IO1,
+ MPP20_GPIO,
+ MPP21_GPIO, /* USB power */
+ MPP22_GPIO,
+ MPP23_GPIO,
+ MPP24_GPIO,
+ MPP25_GPIO,
+ MPP26_GPIO,
+ MPP27_GPIO,
+ MPP28_GPIO, /* SYS LED (green) */
+ MPP29_GPIO, /* SYS LED (orange) */
+ MPP30_GPIO,
+ MPP31_GPIO,
+ MPP32_GPIO,
+ MPP33_GPIO,
+ MPP34_GPIO,
+ MPP35_GPIO,
+ MPP36_GPIO, /* reset button */
+ MPP37_GPIO, /* copy button */
+ MPP38_GPIO, /* VID B0 */
+ MPP39_GPIO, /* COPY LED (green) */
+ MPP40_GPIO, /* COPY LED (red) */
+ MPP41_GPIO, /* HDD1 LED (green) */
+ MPP42_GPIO, /* HDD1 LED (red) */
+ MPP43_GPIO, /* HTP pin */
+ MPP44_GPIO, /* buzzer */
+ MPP45_GPIO, /* VID B1 */
+ MPP46_GPIO, /* power button */
+ MPP47_GPIO, /* HDD2 power */
+ MPP48_GPIO, /* power off */
+ 0
+ };
+ kirkwood_mpp_conf(kwmpp_config, NULL);
+ return 0;
+}
+
+int board_init(void)
+{
+
+ /* address of boot parameters */
+ gd->bd->bi_boot_params = mvebu_sdram_bar(0) + 0x100;
+
+ /* This disables the hardware watchdog in the mcu on this board. */
+ kw_gpio_set_valid(14, 1);
+ kw_gpio_direction_output(14, 0);
+ kw_gpio_set_value(14, 1);
+
+ return 0;
+}
+
+#ifdef CONFIG_RESET_PHY_R
+/* Configure and enable MV88E1318 PHY */
+void reset_phy(void)
+{
+ u16 reg;
+ u16 devadr;
+ char *name = "egiga0";
+
+ if (miiphy_set_current_dev(name))
+ return;
+
+ /* command to read PHY dev address */
+ if (miiphy_read(name, 0xEE, 0xEE, (u16 *) &devadr)) {
+ printf("Err..%s could not read PHY dev address\n",
+ __FUNCTION__);
+ return;
+ }
+
+ /* Set RGMII delay */
+ miiphy_write(name, devadr, MV88E1318_PGADR_REG, MV88E1318_MAC_CTRL_PG);
+ miiphy_read(name, devadr, MV88E1318_MAC_CTRL_REG, &reg);
+ reg |= (MV88E1318_RGMII_RXTM_CTRL | MV88E1318_RGMII_TXTM_CTRL);
+ miiphy_write(name, devadr, MV88E1318_MAC_CTRL_REG, reg);
+ miiphy_write(name, devadr, MV88E1318_PGADR_REG, 0);
+
+ /* reset the phy */
+ miiphy_reset(name, devadr);
+
+ /* The ZyXEL NSA325 uses the 88E1310S Alaska (interface identical to 88E1318) */
+ /* and has an MCU attached to the LED[2] via tristate interrupt */
+ reg = 0;
+
+ /* switch to LED register page */
+ miiphy_write(name, devadr, MV88E1318_PGADR_REG, MV88E1318_LED_PG);
+ /* read out LED polarity register */
+ miiphy_read(name, devadr, MV88E1318_LED_POL_REG, &reg);
+ /* clear 4, set 5 - LED2 low, tri-state */
+ reg &= ~(MV88E1318_LED2_4);
+ reg |= (MV88E1318_LED2_5);
+ /* write back LED polarity register */
+ miiphy_write(name, devadr, MV88E1318_LED_POL_REG, reg);
+ /* jump back to page 0, per the PHY chip documenation. */
+ miiphy_write(name, devadr, MV88E1318_PGADR_REG, 0);
+
+ /* Set the phy back to auto-negotiation mode. Onboard mcu sets it as 10Mbits/s on poweroff for WoL function */
+ miiphy_write(name, devadr, 0x4, 0x1e1);
+ miiphy_write(name, devadr, 0x9, 0x300);
+ /* Downshift */
+ miiphy_write(name, devadr, 0x10, 0x3860);
+ miiphy_write(name, devadr, 0x0, 0x9140);
+
+ printf("MV88E1318 PHY initialized on %s\n", name);
+
+}
+#endif /* CONFIG_RESET_PHY_R */
+
+#ifdef CONFIG_SHOW_BOOT_PROGRESS
+void show_boot_progress(int val)
+{
+ struct kwgpio_registers *gpio0 = (struct kwgpio_registers *)MVEBU_GPIO0_BASE;
+ u32 dout0 = readl(&gpio0->dout);
+ u32 blen0 = readl(&gpio0->blink_en);
+
+ struct kwgpio_registers *gpio1 = (struct kwgpio_registers *)MVEBU_GPIO1_BASE;
+ u32 dout1 = readl(&gpio1->dout);
+ u32 blen1 = readl(&gpio1->blink_en);
+
+ switch (val) {
+ case BOOTSTAGE_ID_DECOMP_IMAGE:
+ writel(blen0 & ~(SYS_GREEN_LED | SYS_ORANGE_LED), &gpio0->blink_en);
+ writel((dout0 & ~SYS_GREEN_LED) | SYS_ORANGE_LED, &gpio0->dout);
+ break;
+ case BOOTSTAGE_ID_RUN_OS:
+ writel(dout0 & ~SYS_ORANGE_LED, &gpio0->dout);
+ writel(blen0 | SYS_GREEN_LED, &gpio0->blink_en);
+ break;
+ case BOOTSTAGE_ID_NET_START:
+ writel(dout1 & ~COPY_RED_LED, &gpio1->dout);
+ writel((blen1 & ~COPY_RED_LED) | COPY_GREEN_LED, &gpio1->blink_en);
+ break;
+ case BOOTSTAGE_ID_NET_LOADED:
+ writel(blen1 & ~(COPY_RED_LED | COPY_GREEN_LED), &gpio1->blink_en);
+ writel((dout1 & ~COPY_RED_LED) | COPY_GREEN_LED, &gpio1->dout);
+ break;
+ case -BOOTSTAGE_ID_NET_NETLOOP_OK:
+ case -BOOTSTAGE_ID_NET_LOADED:
+ writel(dout1 & ~COPY_GREEN_LED, &gpio1->dout);
+ writel((blen1 & ~COPY_GREEN_LED) | COPY_RED_LED, &gpio1->blink_en);
+ break;
+ default:
+ if (val < 0) {
+ /* error */
+ printf("Error occured, error code = %d\n", -val);
+ writel(dout0 & ~SYS_GREEN_LED, &gpio0->dout);
+ writel(blen0 | SYS_ORANGE_LED, &gpio0->blink_en);
+ }
+ break;
+ }
+}
+#endif
+
+#if defined(CONFIG_KIRKWOOD_GPIO)
+/* Return GPIO button status */
+/*
+un-pressed:
+ gpio-36 (Reset Button ) in hi (act lo) - IRQ edge (clear )
+ gpio-37 (Copy Button ) in hi (act lo) - IRQ edge (clear )
+ gpio-46 (Power Button ) in lo (act hi) - IRQ edge (clear )
+pressed
+ gpio-36 (Reset Button ) in lo (act hi) - IRQ edge (clear )
+ gpio-37 (Copy Button ) in lo (act hi) - IRQ edge (clear )
+ gpio-46 (Power Button ) in hi (act lo) - IRQ edge (clear )
+*/
+
+static int
+do_read_button(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[])
+{
+ if (strcmp(argv[1], "power") == 0) {
+ kw_gpio_set_valid(BTN_POWER, GPIO_INPUT_OK);
+ kw_gpio_direction_input(BTN_POWER);
+ return !kw_gpio_get_value(BTN_POWER);
+ }
+ else if (strcmp(argv[1], "reset") == 0)
+ return kw_gpio_get_value(BTN_RESET);
+ else if (strcmp(argv[1], "copy") == 0)
+ return kw_gpio_get_value(BTN_COPY);
+ else
+ return -1;
+}
+
+
+U_BOOT_CMD(button, 2, 0, do_read_button,
+ "Return GPIO button status 0=off 1=on",
+ "- button power|reset|copy: test buttons states\n"
+);
+
+#endif
+
--- /dev/null
+++ b/board/zyxel/nsa325/nsa325.h
@@ -0,0 +1,77 @@
+/*
+ * Copyright (C) 2014 Jason Plum <jplum@archlinuxarm.org>
+ *
+ * Based on nsa320.h originall written by
+ * Copyright (C) 2012 Peter Schildmann <linux@schildmann.info>
+ *
+ * Based on guruplug.h originally written by
+ * Siddarth Gore <gores@marvell.com>
+ * (C) Copyright 2009
+ * Marvell Semiconductor <www.marvell.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
+ * MA 02110-1301 USA
+ */
+
+#ifndef __NSA325_H
+#define __NSA325_H
+
+/* low GPIO's */
+#define HDD2_GREEN_LED (1 << 12)
+#define HDD2_RED_LED (1 << 13)
+#define USB_GREEN_LED (1 << 15)
+#define USB_POWER (1 << 21)
+#define SYS_GREEN_LED (1 << 28)
+#define SYS_ORANGE_LED (1 << 29)
+
+#define PIN_USB_GREEN_LED 15
+#define PIN_USB_POWER 21
+
+#define NSA325_OE_LOW (~(HDD2_GREEN_LED | HDD2_RED_LED | \
+ USB_GREEN_LED | USB_POWER | \
+ SYS_GREEN_LED | SYS_ORANGE_LED))
+#define NSA325_VAL_LOW (SYS_GREEN_LED | USB_POWER)
+
+/* high GPIO's */
+#define COPY_GREEN_LED (1 << 7)
+#define COPY_RED_LED (1 << 8)
+#define HDD1_GREEN_LED (1 << 9)
+#define HDD1_RED_LED (1 << 10)
+#define HDD2_POWER (1 << 15)
+#define WATCHDOG_SIGNAL (1 << 14)
+
+#define NSA325_OE_HIGH (~(COPY_GREEN_LED | COPY_RED_LED | \
+ HDD1_GREEN_LED | HDD1_RED_LED | HDD2_POWER | WATCHDOG_SIGNAL ))
+#define NSA325_VAL_HIGH (WATCHDOG_SIGNAL | HDD2_POWER)
+
+/* PHY related */
+#define MV88E1318_PGADR_REG 22
+#define MV88E1318_MAC_CTRL_PG 2
+#define MV88E1318_MAC_CTRL_REG 21
+#define MV88E1318_RGMII_TXTM_CTRL (1 << 4)
+#define MV88E1318_RGMII_RXTM_CTRL (1 << 5)
+#define MV88E1318_LED_PG 3
+#define MV88E1318_LED_POL_REG 17
+#define MV88E1318_LED2_4 (1 << 4)
+#define MV88E1318_LED2_5 (1 << 5)
+
+#define BTN_POWER 46
+#define BTN_RESET 36
+#define BTN_COPY 37
+
+#endif /* __NSA325_H */
--- /dev/null
+++ b/configs/nsa325_defconfig
@@ -0,0 +1,37 @@
+CONFIG_ARM=y
+CONFIG_KIRKWOOD=y
+CONFIG_SYS_TEXT_BASE=0x600000
+CONFIG_TARGET_NSA325=y
+CONFIG_IDENT_STRING="\nZyXEL NSA325 2-Bay Power Media Server"
+CONFIG_BOOTDELAY=3
+CONFIG_SYS_PROMPT="NSA325> "
+# CONFIG_CMD_IMLS is not set
+# CONFIG_CMD_FLASH is not set
+CONFIG_SYS_NS16550=y
+CONFIG_CMD_FDT=y
+CONFIG_OF_LIBFDT=y
+CONFIG_CMD_SETEXPR=y
+CONFIG_CMD_DHCP=y
+CONFIG_CMD_MII=y
+CONFIG_CMD_PING=y
+CONFIG_CMD_DNS=y
+CONFIG_CMD_SNTP=y
+CONFIG_CMD_USB=y
+CONFIG_USB=y
+CONFIG_CMD_DATE=y
+CONFIG_CMD_EXT2=y
+CONFIG_CMD_EXT4=y
+CONFIG_CMD_FAT=y
+CONFIG_CMD_JFFS2=y
+CONFIG_MTDPARTS_DEFAULT="mtdparts=orion_nand:0x0c0000(uboot),0x80000(uboot_env),0x7ec0000(ubi)"
+CONFIG_CMD_MTDPARTS=y
+CONFIG_CMD_ENV=y
+CONFIG_CMD_NAND=y
+CONFIG_EFI_PARTITION=y
+CONFIG_ENV_IS_IN_NAND=y
+CONFIG_CMD_UBI=y
+CONFIG_USB_EHCI_HCD=y
+CONFIG_USB_STORAGE=y
+CONFIG_LZMA=y
+CONFIG_LZO=y
+CONFIG_SYS_LONGHELP=y
--- /dev/null
+++ b/include/configs/nsa325.h
@@ -0,0 +1,122 @@
+/*
+ * (C) Copyright 2016 bodhi <mibodhi@gmail.com>
+ *
+ * Based on
+ * Copyright (C) 2014 Jason Plum <jplum@archlinuxarm.org>
+ * Based on
+ * Copyright (C) 2012 Peter Schildmann <linux@schildmann.info>
+ *
+ * Based on guruplug.h originally written by
+ * Siddarth Gore <gores@marvell.com>
+ * (C) Copyright 2009
+ * Marvell Semiconductor <www.marvell.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
+ * MA 02110-1301 USA
+ */
+
+#ifndef _CONFIG_NSA325_H
+#define _CONFIG_NSA325_H
+
+/*
+ * High Level Configuration Options (easy to change)
+ */
+#define CONFIG_FEROCEON_88FR131 1 /* CPU Core subversion */
+#define CONFIG_KW88F6281 1 /* SOC Name */
+
+#define CONFIG_SKIP_LOWLEVEL_INIT /* disable board lowlevel_init */
+
+/*
+ * Misc Configuration Options
+ */
+#define CONFIG_SHOW_BOOT_PROGRESS 1 /* boot progess display (LED's) */
+
+/*
+ * Commands configuration
+ */
+#define CONFIG_PREBOOT
+
+/*
+ * mv-common.h should be defined after CMD configs since it used them
+ * to enable certain macros
+ */
+#include "mv-common.h"
+
+/*
+ * Environment variables configurations
+ */
+#ifdef CONFIG_CMD_NAND
+#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K */
+#endif
+/*
+ * max 4k env size is enough, but in case of nand
+ * it has to be rounded to sector size
+ */
+#define CONFIG_ENV_SIZE 0x20000 /* 128k */
+#define CONFIG_ENV_ADDR 0xc0000
+#define CONFIG_ENV_OFFSET 0xc0000 /* env starts here */
+
+/*
+ * Default environment variables
+ */
+#define CONFIG_BOOTCOMMAND \
+ "ubi part ubi; " \
+ "ubi read 0x800000 kernel; " \
+ "bootm 0x800000"
+
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ "console=console=ttyS0,115200\0" \
+ "mtdids=nand0=orion_nand\0" \
+ "mtdparts="CONFIG_MTDPARTS_DEFAULT "\0" \
+ "bootargs_root=\0"
+
+/*
+ * Ethernet Driver configuration
+ */
+#ifdef CONFIG_CMD_NET
+#define CONFIG_MVGBE_PORTS {1, 0} /* enable port 0 only */
+#define CONFIG_PHY_BASE_ADR 0x1
+#define CONFIG_NETCONSOLE
+#endif /* CONFIG_CMD_NET */
+
+/*
+ * SATA Driver configuration
+ */
+#ifdef CONFIG_MVSATA_IDE
+#define CONFIG_SYS_ATA_IDE0_OFFSET MV_SATA_PORT0_OFFSET
+#define CONFIG_SYS_ATA_IDE1_OFFSET MV_SATA_PORT1_OFFSET
+#endif /* CONFIG_MVSATA_IDE */
+
+/*
+ * File system
+ */
+#define CONFIG_JFFS2_NAND
+#define CONFIG_JFFS2_LZO
+#define CONFIG_MTD_DEVICE /* needed for mtdparts commands */
+#define CONFIG_MTD_PARTITIONS
+
+/*
+ * Date Time
+ */
+#ifdef CONFIG_CMD_DATE
+#define CONFIG_RTC_MV
+#endif /* CONFIG_CMD_DATE */
+
+#define CONFIG_KIRKWOOD_GPIO /* Enable GPIO Support */
+
+#endif /* _CONFIG_NSA325_H */
Reference in New Issue View Git Blame Copy Permalink