mirror of
https://github.com/openwrt/openwrt.git
synced 2024-12-25 00:11:13 +00:00
91 lines
3.0 KiB
Diff
91 lines
3.0 KiB
Diff
From 34e6cb1e6f79b24d66353f7c0ac75cd0ae749208 Mon Sep 17 00:00:00 2001
|
|
From: Tim Gover <tim.gover@raspberrypi.org>
|
|
Date: Wed, 9 Jan 2019 14:43:36 +0000
|
|
Subject: [PATCH 550/773] pinctrl-bcm2835: Add support for BCM2838
|
|
|
|
GPIO configuration on BCM2838 is largely the same as BCM2835 except for
|
|
the pull up/down configuration. The old mechanism has been replaced
|
|
by new registers which don't require the fixed delay.
|
|
|
|
Detect BCN2838 at run-time and use the new mechanism. Backwards
|
|
compatibility for the device-tree configuration has been retained.
|
|
---
|
|
drivers/pinctrl/bcm/pinctrl-bcm2835.c | 58 ++++++++++++++++++++-------
|
|
1 file changed, 44 insertions(+), 14 deletions(-)
|
|
|
|
--- a/drivers/pinctrl/bcm/pinctrl-bcm2835.c
|
|
+++ b/drivers/pinctrl/bcm/pinctrl-bcm2835.c
|
|
@@ -67,6 +67,12 @@
|
|
#define GPPUD 0x94 /* Pin Pull-up/down Enable */
|
|
#define GPPUDCLK0 0x98 /* Pin Pull-up/down Enable Clock */
|
|
|
|
+/* 2711 has a different mechanism for pin pull-up/down/enable */
|
|
+#define GPPUPPDN0 0xe4 /* Pin pull-up/down for pins 15:0 */
|
|
+#define GPPUPPDN1 0xe8 /* Pin pull-up/down for pins 31:16 */
|
|
+#define GPPUPPDN2 0xec /* Pin pull-up/down for pins 47:32 */
|
|
+#define GPPUPPDN3 0xf0 /* Pin pull-up/down for pins 57:48 */
|
|
+
|
|
#define FSEL_REG(p) (GPFSEL0 + (((p) / 10) * 4))
|
|
#define FSEL_SHIFT(p) (((p) % 10) * 3)
|
|
#define GPIO_REG_OFFSET(p) ((p) / 32)
|
|
@@ -917,21 +923,45 @@ static void bcm2835_pull_config_set(stru
|
|
unsigned int pin, unsigned int arg)
|
|
{
|
|
u32 off, bit;
|
|
+ /* BCM2835, BCM2836 & BCM2837 return 'gpio' for this unused register */
|
|
+ int is_2835 = bcm2835_gpio_rd(pc, GPPUPPDN3) == 0x6770696f;
|
|
|
|
- off = GPIO_REG_OFFSET(pin);
|
|
- bit = GPIO_REG_SHIFT(pin);
|
|
-
|
|
- bcm2835_gpio_wr(pc, GPPUD, arg & 3);
|
|
- /*
|
|
- * BCM2835 datasheet say to wait 150 cycles, but not of what.
|
|
- * But the VideoCore firmware delay for this operation
|
|
- * based nearly on the same amount of VPU cycles and this clock
|
|
- * runs at 250 MHz.
|
|
- */
|
|
- udelay(1);
|
|
- bcm2835_gpio_wr(pc, GPPUDCLK0 + (off * 4), BIT(bit));
|
|
- udelay(1);
|
|
- bcm2835_gpio_wr(pc, GPPUDCLK0 + (off * 4), 0);
|
|
+ if (is_2835) {
|
|
+ off = GPIO_REG_OFFSET(pin);
|
|
+ bit = GPIO_REG_SHIFT(pin);
|
|
+ /*
|
|
+ * BCM2835 datasheet say to wait 150 cycles, but not of what.
|
|
+ * But the VideoCore firmware delay for this operation
|
|
+ * based nearly on the same amount of VPU cycles and this clock
|
|
+ * runs at 250 MHz.
|
|
+ */
|
|
+ bcm2835_gpio_wr(pc, GPPUD, arg & 3);
|
|
+ udelay(1);
|
|
+ bcm2835_gpio_wr(pc, GPPUDCLK0 + (off * 4), BIT(bit));
|
|
+ udelay(1);
|
|
+ bcm2835_gpio_wr(pc, GPPUDCLK0 + (off * 4), 0);
|
|
+ } else {
|
|
+ u32 reg;
|
|
+ int lsb;
|
|
+
|
|
+ off = (pin >> 4);
|
|
+ if (off > 3)
|
|
+ return;
|
|
+ lsb = (pin & 0xf) << 1;
|
|
+
|
|
+ /* The up/down semantics are reversed compared to BCM2835.
|
|
+ * Instead of updating all the device tree files, translate the
|
|
+ * values here.
|
|
+ */
|
|
+ if (arg == 2)
|
|
+ arg = 1;
|
|
+ else if (arg == 1)
|
|
+ arg = 2;
|
|
+ reg = bcm2835_gpio_rd(pc, GPPUPPDN0 + (off *4));
|
|
+ reg &= ~(0x3 << lsb);
|
|
+ reg |= (arg & 3) << lsb;
|
|
+ bcm2835_gpio_wr(pc, GPPUPPDN0 + (off * 4), reg);
|
|
+ }
|
|
}
|
|
|
|
static int bcm2835_pinconf_set(struct pinctrl_dev *pctldev,
|