mirror of
https://github.com/openwrt/openwrt.git
synced 2024-12-22 15:02:32 +00:00
3a4b751110
The uart node is enabled on all devices except one (GL-USB150 *). Thus, let's not have a few hundred nodes to enable it, but do not disable it in the first place. Where the majority of devices is using it, also move the serial0 alias to the DTSI. *) Since GL-USB150 even defines serial0 alias, the missing uart is probably just a mistake. Anyway, disable it for now so this patch stays cosmetic. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
140 lines
2.1 KiB
Plaintext
140 lines
2.1 KiB
Plaintext
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
|
|
|
#include "qca955x.dtsi"
|
|
|
|
#include <dt-bindings/gpio/gpio.h>
|
|
#include <dt-bindings/input/input.h>
|
|
|
|
/ {
|
|
compatible = "ocedo,ursus", "qca,qca9558";
|
|
model = "OCEDO Ursus";
|
|
|
|
leds {
|
|
compatible = "gpio-leds";
|
|
|
|
wifi2 {
|
|
label = "green:wlan2g";
|
|
gpios = <&gpio 14 GPIO_ACTIVE_LOW>;
|
|
linux,default-trigger = "phy1tpt";
|
|
};
|
|
|
|
wifi5 {
|
|
label = "green:wlan5g";
|
|
gpios = <&gpio 15 GPIO_ACTIVE_LOW>;
|
|
linux,default-trigger = "phy0tpt";
|
|
};
|
|
};
|
|
};
|
|
|
|
&pcie1 {
|
|
status = "okay";
|
|
};
|
|
|
|
&pll {
|
|
clocks = <&extosc>;
|
|
};
|
|
|
|
&spi {
|
|
status = "okay";
|
|
|
|
flash@0 {
|
|
compatible = "jedec,spi-nor";
|
|
reg = <0>;
|
|
spi-max-frequency = <25000000>;
|
|
|
|
partitions {
|
|
compatible = "fixed-partitions";
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
|
|
uboot: partition@0 {
|
|
label = "u-boot";
|
|
reg = <0x000000 0x040000>;
|
|
read-only;
|
|
};
|
|
|
|
partition@40000 {
|
|
label = "u-boot-env";
|
|
reg = <0x040000 0x010000>;
|
|
};
|
|
|
|
partition@50000 {
|
|
compatible = "denx,uimage";
|
|
label = "firmware";
|
|
reg = <0x050000 0x740000>;
|
|
};
|
|
|
|
partition@790000 {
|
|
label = "vendor";
|
|
reg = <0x790000 0x740000>;
|
|
read-only;
|
|
};
|
|
|
|
partition@ed0000 {
|
|
label = "data";
|
|
reg = <0xed0000 0x110000>;
|
|
read-only;
|
|
};
|
|
|
|
partition@fe0000 {
|
|
label = "id";
|
|
reg = <0xfe0000 0x010000>;
|
|
read-only;
|
|
};
|
|
|
|
art: partition@ff0000 {
|
|
label = "art";
|
|
reg = <0xff0000 0x010000>;
|
|
read-only;
|
|
};
|
|
};
|
|
};
|
|
};
|
|
|
|
&wmac {
|
|
status = "okay";
|
|
|
|
mtd-cal-data = <&art 0x1000>;
|
|
mtd-mac-address = <&art 0x06>;
|
|
};
|
|
|
|
&mdio0 {
|
|
status = "okay";
|
|
|
|
phy1: ethernet-phy@1 {
|
|
reg = <1>;
|
|
};
|
|
|
|
phy2: ethernet-phy@2 {
|
|
reg = <2>;
|
|
at803x-override-sgmii-link-check;
|
|
};
|
|
};
|
|
|
|
ð0 {
|
|
status = "okay";
|
|
mtd-mac-address = <&art 0x00>;
|
|
|
|
phy-mode = "rgmii-rxid";
|
|
phy-handle = <&phy1>;
|
|
pll-data = <0x8e000000 0x80000101 0x80001313>;
|
|
|
|
gmac_config: gmac-config {
|
|
device = <&gmac>;
|
|
|
|
rxdv-delay = <3>;
|
|
rxd-delay = <3>;
|
|
txen-delay = <0>;
|
|
txd-delay = <0>;
|
|
rgmii-enabled = <1>;
|
|
};
|
|
};
|
|
|
|
ð1 {
|
|
status = "okay";
|
|
mtd-mac-address = <&art 0x12>;
|
|
phy-handle = <&phy2>;
|
|
pll-data = <0x3000101 0x101 0x1313>;
|
|
qca955x-sgmii-fixup;
|
|
};
|