mirror of
https://github.com/openwrt/openwrt.git
synced 2024-12-26 00:41:17 +00:00
95e241d2af
On the ramips target, all 'wmac' nodes in SoC dtsi are enabled by default except mt7628. There is no need to mark them as 'okay' again. So these useless properties can be removed. Signed-off-by: Shiji Yang <yangshiji66@qq.com>
131 lines
2.1 KiB
Plaintext
131 lines
2.1 KiB
Plaintext
#include "rt2880.dtsi"
|
|
|
|
#include <dt-bindings/gpio/gpio.h>
|
|
#include <dt-bindings/input/input.h>
|
|
|
|
/ {
|
|
compatible = "airlink101,ar725w", "ralink,rt2880-soc";
|
|
model = "Airlink101 AR725W";
|
|
|
|
aliases {
|
|
led-boot = &led_power;
|
|
led-failsafe = &led_power;
|
|
led-running = &led_power;
|
|
led-upgrade = &led_power;
|
|
};
|
|
|
|
flash@bdc00000 {
|
|
compatible = "cfi-flash";
|
|
reg = <0xbc400000 0x800000>;
|
|
bank-width = <2>;
|
|
|
|
partitions {
|
|
compatible = "fixed-partitions";
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
|
|
partition@0 {
|
|
reg = <0x0 0x30000>;
|
|
label = "u-boot";
|
|
read-only;
|
|
};
|
|
|
|
partition@30000 {
|
|
reg = <0x30000 0x10000>;
|
|
label = "u-boot-env";
|
|
};
|
|
|
|
factory: partition@40000 {
|
|
compatible = "nvmem-cells";
|
|
label = "factory";
|
|
reg = <0x40000 0x10000>;
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
read-only;
|
|
|
|
eeprom_factory_0: eeprom@0 {
|
|
reg = <0x0 0x200>;
|
|
};
|
|
|
|
macaddr_factory_4: macaddr@4 {
|
|
reg = <0x4 0x6>;
|
|
};
|
|
};
|
|
|
|
partition@50000 {
|
|
compatible = "denx,uimage";
|
|
reg = <0x50000 0x3B0000>;
|
|
label = "firmware";
|
|
};
|
|
};
|
|
};
|
|
|
|
leds {
|
|
compatible = "gpio-leds";
|
|
|
|
led_power: power {
|
|
label = "green:power";
|
|
gpios = <&gpio0 7 GPIO_ACTIVE_HIGH>;
|
|
};
|
|
|
|
wpsred {
|
|
label = "red:wps";
|
|
gpios = <&gpio0 8 GPIO_ACTIVE_LOW>;
|
|
};
|
|
|
|
wpsblue {
|
|
label = "blue:wps";
|
|
gpios = <&gpio0 13 GPIO_ACTIVE_LOW>;
|
|
};
|
|
};
|
|
|
|
keys {
|
|
compatible = "gpio-keys-polled";
|
|
poll-interval = <100>;
|
|
|
|
wps {
|
|
label = "wps";
|
|
gpios = <&gpio0 0 GPIO_ACTIVE_LOW>;
|
|
linux,code = <KEY_WPS_BUTTON>;
|
|
};
|
|
|
|
reset {
|
|
label = "reset";
|
|
gpios = <&gpio0 9 GPIO_ACTIVE_LOW>;
|
|
linux,code = <KEY_RESTART>;
|
|
};
|
|
};
|
|
};
|
|
|
|
&state_default {
|
|
gpio {
|
|
groups = "i2c", "spi", "uartlite";
|
|
function = "gpio";
|
|
};
|
|
};
|
|
|
|
ðernet {
|
|
status = "okay";
|
|
nvmem-cells = <&macaddr_factory_4>;
|
|
nvmem-cell-names = "mac-address";
|
|
|
|
port@0 {
|
|
phy-handle = <&phy0>;
|
|
phy-mode = "mii";
|
|
};
|
|
|
|
mdio-bus {
|
|
status = "okay";
|
|
|
|
phy0: ethernet-phy@0 {
|
|
phy-mode = "mii";
|
|
reg = <0>;
|
|
};
|
|
};
|
|
};
|
|
|
|
&wmac {
|
|
nvmem-cells = <&eeprom_factory_0>;
|
|
nvmem-cell-names = "eeprom";
|
|
};
|