mirror of
https://github.com/openwrt/openwrt.git
synced 2024-12-30 18:47:06 +00:00
643fcfc8d6
NEC Aterm WG1200CR is a 2.4/5 GHz band 11ac router, based on Qualcomm Atheros QCA9563. Specification: - SoC : Qualcomm Atheros QCA9563 - RAM : DDR2 128 MiB - Flash : SPI-NOR 8 MiB - WLAN : 2.4/5 GHz 2T2R - 2.4 GHz : QCA9563 (SoC) - 5 GHz : QCA9888 - Ethernet : 2x 10/100/1000 Mbps - Switch : QCA8334 - LEDs/Input : 12x/4x (2x buttons, 1x slide-switch) - UART : through-hole on PCB - JP1: Vcc, GND, NC, TX, RX from power connector side - 115200 bps Flash instruction using factory image: 1. Boot WG1200CR normaly 2. Access to "http://192.168.10.1/" and open firmware update page ("ファームウェア更新") 3. Select the OpenWrt factory image and click update ("更新") button to perform firmware update 4. Wait ~150 seconds to complete flashing Known issues: - cannot be controlled LEDs other than Power (Green/Red) - only Power LEDs are connected to SoC GPIO; other LEDs connected to the gpiochip on ath10k chip (QCA9888) Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com> Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [commit message formatting]
177 lines
2.9 KiB
Plaintext
177 lines
2.9 KiB
Plaintext
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
|
/dts-v1/;
|
|
|
|
#include <dt-bindings/gpio/gpio.h>
|
|
#include <dt-bindings/input/input.h>
|
|
|
|
#include "qca956x.dtsi"
|
|
|
|
/ {
|
|
model = "NEC Aterm WG1200CR";
|
|
compatible = "nec,wg1200cr", "qca,qca9563";
|
|
|
|
chosen {
|
|
bootargs = "console=ttyS0,115200n8";
|
|
};
|
|
|
|
aliases {
|
|
led-boot = &power_green;
|
|
led-failsafe = &power_red;
|
|
led-running = &power_green;
|
|
led-upgrade = &power_green;
|
|
};
|
|
|
|
leds {
|
|
compatible = "gpio-leds";
|
|
/* other LEDs are connected to ath10k (QCA9888) gpiochip */
|
|
|
|
power_green: power_green {
|
|
label = "wg1200cr:green:power";
|
|
gpios = <&gpio 5 GPIO_ACTIVE_LOW>;
|
|
default-state = "on";
|
|
};
|
|
|
|
power_red: power_red {
|
|
label = "wg1200cr:red:power";
|
|
gpios = <&gpio 6 GPIO_ACTIVE_LOW>;
|
|
};
|
|
};
|
|
|
|
keys {
|
|
compatible = "gpio-keys";
|
|
|
|
reset {
|
|
label = "reset";
|
|
gpios = <&gpio 1 GPIO_ACTIVE_LOW>;
|
|
linux,code = <KEY_RESTART>;
|
|
debounce-interval = <60>;
|
|
};
|
|
|
|
wps {
|
|
label = "wps";
|
|
gpios = <&gpio 2 GPIO_ACTIVE_LOW>;
|
|
linux,code = <KEY_WPS_BUTTON>;
|
|
debounce-interval = <60>;
|
|
};
|
|
|
|
bridge {
|
|
label = "br";
|
|
gpios = <&gpio 7 GPIO_ACTIVE_LOW>;
|
|
linux,code = <BTN_0>;
|
|
linux,input-type = <EV_SW>;
|
|
debounce-interval = <60>;
|
|
};
|
|
|
|
converter {
|
|
label = "cnv";
|
|
gpios = <&gpio 8 GPIO_ACTIVE_LOW>;
|
|
linux,code = <BTN_0>;
|
|
linux,input-type = <EV_SW>;
|
|
debounce-interval = <60>;
|
|
};
|
|
};
|
|
};
|
|
|
|
&spi {
|
|
status = "okay";
|
|
num-cs = <1>;
|
|
|
|
flash@0 {
|
|
compatible = "jedec,spi-nor";
|
|
reg = <0>;
|
|
spi-max-frequency = <25000000>;
|
|
|
|
partitions {
|
|
compatible = "fixed-partitions";
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
|
|
partition@0 {
|
|
label = "u-boot";
|
|
reg = <0x000000 0x040000>;
|
|
read-only;
|
|
};
|
|
|
|
partition@40000 {
|
|
label = "devdata";
|
|
reg = <0x040000 0x010000>;
|
|
read-only;
|
|
};
|
|
|
|
partition@50000 {
|
|
label = "devconf";
|
|
reg = <0x050000 0x010000>;
|
|
read-only;
|
|
};
|
|
|
|
partition@60000 {
|
|
label = "misc";
|
|
reg = <0x060000 0x010000>;
|
|
read-only;
|
|
};
|
|
|
|
partition@70000 {
|
|
label = "wifimngdata";
|
|
reg = <0x070000 0x010000>;
|
|
read-only;
|
|
};
|
|
|
|
partition@80000 {
|
|
compatible = "seama";
|
|
label = "firmware";
|
|
reg = <0x080000 0x770000>;
|
|
};
|
|
|
|
partition@7f0000 {
|
|
label = "art";
|
|
reg = <0x7f0000 0x010000>;
|
|
read-only;
|
|
};
|
|
};
|
|
};
|
|
};
|
|
|
|
&mdio0 {
|
|
status = "okay";
|
|
|
|
phy0: ethernet-phy@0 {
|
|
reg = <0>;
|
|
|
|
qca,ar8327-initvals = <
|
|
0x04 0x00000080 /* PORT0 PAD MODE CTRL */
|
|
0x50 0xcc35cc35 /* LED_CTRL0 */
|
|
0x54 0xca35ca35 /* LED_CTRL1 */
|
|
0x58 0xc935c935 /* LED_CTRL2 */
|
|
0x5c 0x03ffff00 /* LED_CTRL3 */
|
|
0x7c 0x0000007e /* PORT0_STATUS */
|
|
>;
|
|
};
|
|
};
|
|
|
|
ð0 {
|
|
status = "okay";
|
|
|
|
pll-data = <0x03000101 0x00000101 0x00001919>;
|
|
|
|
phy-mode = "sgmii";
|
|
phy-handle = <&phy0>;
|
|
};
|
|
|
|
&pcie {
|
|
status = "okay";
|
|
|
|
wifi@0,0 {
|
|
compatible = "pci168c,0056";
|
|
reg = <0x0000 0 0 0 0>;
|
|
};
|
|
};
|
|
|
|
&uart {
|
|
status = "okay";
|
|
};
|
|
|
|
&wmac {
|
|
status = "okay";
|
|
qca,no-eeprom;
|
|
};
|