mirror of
https://github.com/openwrt/openwrt.git
synced 2024-12-27 01:11:14 +00:00
2b4ac79a79
SOC: IPQ4018 / QCA Dakota CPU: Quad-Core ARMv7 Processor rev 5 (v7l) Cortex-A7 DRAM: 256 MiB NOR: 32 MiB ETH: Qualcomm Atheros QCA8072 WLAN1: Qualcomm Atheros QCA4018 2.4GHz 802.11bgn 2:2x2 WLAN2: Qualcomm Atheros QCA4018 5GHz 802.11a/n/ac 2:2x2 INPUT: RESET Button LEDS: Power, LAN, MESH, WLAN 2.4GHz, WLAN 5GHz 1. Load Ramdisk via U-Boot To set up the flash memory environment, do the following: a. As a preliminary step, ensure that the board console port is connected to the PC using these RS232 parameters: * 115200bps * 8N1 b. Confirm that the PC is connected to the board using one of the Ethernet ports. Set a static ip 192.168.99.8 for Ethernet that connects to board. The PC must have a TFTP server launched and listening on the interface to which the board is connected. At this stage power up the board and, after a few seconds, press 4 and then any key during the countdown. U-BOOT> set serverip 192.168.99.8 && set ipaddr 192.168.99.9 && tftpboot 0x84000000 openwrt.itb && bootm 2. Load image via GUI a. Upgrade EAP1300 to FW v3.5.3.2 In the GUI, System Manager > Firmware > Firmware Upgrade, to do upgrade. b. Transfer to OpenWrt from EnGenius. In Firmware Upgrade page, to upgrade yours openwrt-ipq40xx-engenius_eap1300-squashfs-sysupgrade.bin. 3. Revert to EnGenius EAP1300 To flash openwrt-ipq40xx-engenius_eap1300-squashfs-factory.bin by using sysupgrade command and "DO NOT" keep configuration. $ sysupgrade –n openwrt-ipq40xx-engenius_eap1300-squashfs-factory.bin Signed-off-by: Steven Lin <steven.lin@senao.com>
59 lines
1.9 KiB
Bash
Executable File
59 lines
1.9 KiB
Bash
Executable File
#!/bin/sh
|
|
#
|
|
# Copyright (C) 2015 OpenWrt.org
|
|
#
|
|
|
|
. /lib/functions/uci-defaults.sh
|
|
|
|
board_config_update
|
|
|
|
board=$(board_name)
|
|
boardname="${board##*,}"
|
|
|
|
case "$board" in
|
|
asus,rt-ac58u)
|
|
ucidef_set_led_wlan "wlan2g" "WLAN2G" "${boardname}:blue:wlan2G" "phy0tpt"
|
|
ucidef_set_led_wlan "wlan5g" "WLAN5G" "${boardname}:blue:wlan5G" "phy1tpt"
|
|
ucidef_set_led_usbport "usb" "USB" "${boardname}:blue:usb" "usb1-port1" "usb2-port1" "usb3-port1" "usb4-port1"
|
|
ucidef_set_led_netdev "wan" "WAN" "${boardname}:blue:wan" "eth1"
|
|
ucidef_set_led_switch "lan" "LAN" "${boardname}:blue:lan" "switch0" "0x1e"
|
|
;;
|
|
avm,fritzbox-4040)
|
|
ucidef_set_led_wlan "wlan" "WLAN" "fritz4040:green:wlan" "phy0tpt" "phy1tpt"
|
|
ucidef_set_led_netdev "wan" "WAN" "fritz4040:green:wan" "eth1"
|
|
ucidef_set_led_switch "lan" "LAN" "fritz4040:green:lan" "switch0" "0x1e"
|
|
;;
|
|
engenius,eap1300)
|
|
ucidef_set_led_netdev "lan" "LAN" "${boardname}:blue:lan" "eth0"
|
|
ucidef_set_led_wlan "wlan2g" "WLAN2G" "${boardname}:blue:wlan2g" "phy0tpt"
|
|
ucidef_set_led_wlan "wlan5g" "WLAN5G" "${boardname}:yellow:wlan5g" "phy1tpt"
|
|
ucidef_set_led_default "mesh" "MESH" "${boardname}:blue:mesh" "0"
|
|
;;
|
|
glinet,gl-b1300)
|
|
ucidef_set_led_wlan "wlan" "WLAN" "${boardname}:green:wlan" "phy0tpt"
|
|
;;
|
|
netgear,ex6100v2 |\
|
|
netgear,ex6150v2)
|
|
ucidef_set_led_wlan "wlan2g" "WLAN2G" "ex61x0v2:green:router" "phy0tpt"
|
|
ucidef_set_led_wlan "wlan5g" "WLAN5G" "ex61x0v2:green:client" "phy1tpt"
|
|
;;
|
|
meraki,mr33)
|
|
ucidef_set_interface_lan "eth0"
|
|
;;
|
|
zyxel,nbg6617)
|
|
ucidef_set_led_wlan "wlan2g" "WLAN2G" "${boardname}:green:wlan2G" "phy0tpt"
|
|
ucidef_set_led_wlan "wlan5g" "WLAN5G" "${boardname}:green:wlan5G" "phy1tpt"
|
|
ucidef_set_led_usbport "usb" "USB" "${boardname}:green:usb" "usb1-port1" "usb2-port1" "usb3-port1" "usb4-port1"
|
|
;;
|
|
zyxel,wre6606)
|
|
ucidef_set_led_wlan "wlan2g" "WLAN2G" "${boardname}:green:wlan2g" "phy0tpt"
|
|
ucidef_set_led_wlan "wlan5g" "WLAN5G" "${boardname}:green:wlan5g" "phy1tpt"
|
|
;;
|
|
*)
|
|
;;
|
|
esac
|
|
|
|
board_config_flush
|
|
|
|
exit 0
|