mirror of
https://github.com/openwrt/openwrt.git
synced 2024-12-21 22:47:56 +00:00
d03f3dcf3b
Hardware specification ---------------------- * RTL8380M SoC, 1 MIPS 4KEc core @ 500MHz * 256MB DRAM * 32MB NOR Flash * 8 x 10/100/1000BASE-T ports * 2 x SFP ports * Power LED, Fault LED * Reset button on front panel * UART (115200 8N1) via populated standard pin header marked JP1 TODO: The SFP ports use a shared SCL GPIO that the driver cannot handle. The left SFP port (lan9) is defined and fully functional while the laser on the right SFP port (lan10) is off by default. UART pinout ----------- [o]ooo|JP1 | ||`------ GND | |`------- RX | `-------- TX `---------- Vcc (3V3) Installation using OEM webinterface ----------------------------------- 1. Make sure you are running OEM firmware in secondary slot 2. Install squashfs-factory.imag to primary slot by upload via http Installation using serial interface ----------------------------------- 1. Press "a" "c" "p" during message "Enter correct key to stop autoboot" 2. Load image with "upgrade runtime <TFTP IP>:squashfs-sysupgrade.bin" command 3. Switch to primary slot with "setsys bootpartition 0" 4. Store config with "savesys" 5. Boot the image with `boota` command Dual-boot with stock firmware using writable u-boot-env ------------------------------------------------------- From stock to OpenWrt / primary image 1 (CLI as admin): - > boot system image1 - > reboot From OpenWrt to stock / boot image 2: (shell as root) - # fw_setsys bootpartition 1 - # reboot Debrick using serial interface ------------------------------ 1. Press "a" "c" "p" during message "Enter correct key to stop autoboot" 2. Load vendor image with "upgrade runtime <TFTP IP>:LGS310xxxxx.imag" 3. switch to primary partition "setsys bootpartition 0" 4. safe config "savesys" Further documentation --------------------- See https://openwrt.org/toh/linksys/lgs352c It has been developed and tested on device with v1 revision. Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de> Link: https://github.com/openwrt/openwrt/pull/16068 [Add missing 'w' in name of firmware partition] Signed-off-by: Sander Vanheule <sander@svanheule.net>
114 lines
2.6 KiB
Makefile
114 lines
2.6 KiB
Makefile
# SPDX-License-Identifier: GPL-2.0-only
|
|
|
|
include $(TOPDIR)/rules.mk
|
|
include $(INCLUDE_DIR)/image.mk
|
|
|
|
KERNEL_LOADADDR = 0x80100000
|
|
|
|
DEVICE_VARS += \
|
|
BELKIN_HEADER \
|
|
BELKIN_MODEL \
|
|
CAMEO_BOARD_MODEL \
|
|
CAMEO_BOARD_VERSION \
|
|
CAMEO_CUSTOMER_SIGNATURE \
|
|
CAMEO_KERNEL_PART \
|
|
CAMEO_KERNEL_PART_SIZE \
|
|
CAMEO_ROOTFS_PART \
|
|
H3C_DEVICE_ID \
|
|
H3C_PRODUCT_ID \
|
|
LINKSYS_HEADER \
|
|
ZYXEL_VERS
|
|
|
|
define Build/zyxel-vers
|
|
( echo VERS;\
|
|
for hw in $(ZYXEL_VERS); do\
|
|
echo -n "V9.99($$hw.0) | ";\
|
|
date -d @$(SOURCE_DATE_EPOCH) +%m/%d/%Y;\
|
|
done ) >> $@
|
|
endef
|
|
|
|
define Build/cameo-tag
|
|
$(SCRIPT_DIR)/cameo-tag.py $@ $(CAMEO_KERNEL_PART_SIZE)
|
|
endef
|
|
|
|
define Build/cameo-version
|
|
echo -n "OpenWrt" >> $@
|
|
dd if=/dev/zero bs=25 count=1 >> $@
|
|
endef
|
|
|
|
define Build/cameo-headers
|
|
dd if=$@ bs=$(CAMEO_KERNEL_PART_SIZE) count=1 of=$@.kernel_part; \
|
|
dd if=$@ bs=$(CAMEO_KERNEL_PART_SIZE) skip=1 of=$@.rootfs_part; \
|
|
$(SCRIPT_DIR)/cameo-imghdr.py $@.kernel_part $@.kernel_part.hex \
|
|
"$(CAMEO_BOARD_MODEL)" os $(CAMEO_KERNEL_PART) \
|
|
$(CAMEO_CUSTOMER_SIGNATURE) \
|
|
$(CAMEO_BOARD_VERSION) \
|
|
$(KERNEL_LOADADDR); \
|
|
$(SCRIPT_DIR)/cameo-imghdr.py $@.rootfs_part $@.rootfs_part.hex \
|
|
"$(CAMEO_BOARD_MODEL)" squashfs $(CAMEO_ROOTFS_PART) \
|
|
$(CAMEO_CUSTOMER_SIGNATURE) \
|
|
$(CAMEO_BOARD_VERSION); \
|
|
cat $@.kernel_part.hex $@.rootfs_part.hex > $@
|
|
endef
|
|
|
|
define Build/7z
|
|
$(STAGING_DIR_HOST)/bin/7zr a $(@).new -t7z -m0=lzma $(@)
|
|
mv $@.new $@
|
|
endef
|
|
|
|
define Build/h3c-image
|
|
$(STAGING_DIR_HOST)/bin/mkh3cimg \
|
|
-i $(@) \
|
|
-o $(@).new \
|
|
-c 7z \
|
|
-p $(H3C_PRODUCT_ID) \
|
|
-d $(H3C_DEVICE_ID)
|
|
mv $@.new $@
|
|
endef
|
|
|
|
define Build/h3c-vfs
|
|
$(STAGING_DIR_HOST)/bin/mkh3cvfs \
|
|
-i $(@) \
|
|
-o $(@).new \
|
|
-f openwrt-kernel.bin
|
|
mv $@.new $@
|
|
endef
|
|
|
|
define Build/belkin-header
|
|
$(SCRIPT_DIR)/belkin-header.py $(@) $(@).new $(BELKIN_HEADER) ${BELKIN_MODEL}
|
|
mv $@.new $@
|
|
endef
|
|
|
|
define Build/linksys-image
|
|
$(SCRIPT_DIR)/linksys-image.sh $(@) $(@).new $(LINKSYS_MODEL)
|
|
mv $@.new $@
|
|
endef
|
|
|
|
define Device/Default
|
|
PROFILES = Default
|
|
KERNEL := \
|
|
kernel-bin | \
|
|
append-dtb | \
|
|
libdeflate-gzip | \
|
|
uImage gzip
|
|
KERNEL_INITRAMFS := \
|
|
kernel-bin | \
|
|
append-dtb | \
|
|
libdeflate-gzip | \
|
|
uImage gzip
|
|
DEVICE_DTS_DIR := ../dts
|
|
DEVICE_DTS = $$(SOC)_$(1)
|
|
IMAGES := sysupgrade.bin
|
|
IMAGE/sysupgrade.bin := \
|
|
append-kernel | \
|
|
pad-to 64k | \
|
|
append-rootfs | \
|
|
pad-rootfs | \
|
|
check-size | \
|
|
append-metadata
|
|
endef
|
|
|
|
include $(SUBTARGET).mk
|
|
|
|
$(eval $(call BuildImage))
|