openwrt/target/linux/ath79/dts/ar9344_tplink_tl-wr841hp-v2.dts
Saiful Islam 43ec6d64bb ath79: add support for TP-Link TL-WR841HP v2
Specifications:
- AR9344 SoC, 8 MB nor flash, 64 MB DDR2 RAM
- 2x2 9dBi antenna, wifi 2.4Ghz 300Mbps
- 4x Ethernet LAN 10/100, 1x Ethernet WAN 10/100
- 1x WAN, 4x LAN, Wifi, PWR, WPS, SYSTEM Leds
- Reset/WPS button
- Serial UART at J4 onboard: 3.3v GND RX TX, 1152008N1

MAC addresses as verified by OEM firmware:

vendor   OpenWrt   address
LAN      eth0      label
WAN      eth1      label + 1
WLAN     phy0      label

The label MAC address was found in u-boot 0x1fc00.

Installation:
To install openwrt,
- set the device's SSID to each of the following lines,
  making sure to include the backticks.
- set the ssid and click save between each line.

`echo "httpd -k"> /tmp/s`
`echo "sleep 10">> /tmp/s`
`echo "httpd -r&">> /tmp/s`
`echo "sleep 10">> /tmp/s`
`echo "httpd -k">> /tmp/s`
`echo "sleep 10">> /tmp/s`
`echo "httpd -f">> /tmp/s`
`sh /tmp/s`

- Now, wait 60 sec.
- After the reboot sequence, the router may have fallen back to
  its default IP address with the default credentials (admin:admin).
- Log in to the web interface and go the the firmware upload page.
  Select "openwrt-ath79-generic-tplink_tl-wr841hp-v2-squashfs-factory.bin"
  and you're done : the system now accepts the openwrt.

Forum support topic:
https://forum.openwrt.org/t/support-for-tplink-tl-wr841hp-v2/69445/

Signed-off-by: Saiful Islam <si87868@gmail.com>
2022-02-07 00:03:27 +01:00

171 lines
2.7 KiB
Plaintext

// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
#include "ar9344.dtsi"
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>
/ {
model = "TP-Link TL-WR841HP v2";
compatible = "tplink,tl-wr841hp-v2", "qca,ar9344";
aliases {
led-boot = &led_system;
led-failsafe = &led_system;
led-running = &led_system;
led-upgrade = &led_system;
label-mac-device = &wmac;
};
keys {
compatible = "gpio-keys";
reset {
linux,code = <KEY_RESTART>;
gpios = <&gpio 4 GPIO_ACTIVE_HIGH>;
debounce-interval = <60>;
};
};
leds {
compatible = "gpio-leds";
wan {
label = "green:wan";
gpios = <&gpio 11 GPIO_ACTIVE_LOW>;
};
lan1 {
label = "green:lan1";
gpios = <&gpio 12 GPIO_ACTIVE_LOW>;
};
lan2 {
label = "green:lan2";
gpios = <&gpio 13 GPIO_ACTIVE_LOW>;
};
lan3 {
label = "green:lan3";
gpios = <&gpio 14 GPIO_ACTIVE_LOW>;
};
lan4 {
label = "green:lan4";
gpios = <&gpio 15 GPIO_ACTIVE_LOW>;
};
wps {
label = "green:wps";
gpios = <&gpio 16 GPIO_ACTIVE_LOW>;
};
wlan {
label = "green:wlan";
gpios = <&gpio 21 GPIO_ACTIVE_LOW>;
linux,default-trigger = "phy0tpt";
};
led_system: system {
label = "green:system";
gpios = <&gpio 22 GPIO_ACTIVE_LOW>;
default-state = "on";
};
};
};
&ref {
clock-frequency = <40000000>;
};
&spi {
status = "okay";
flash@0 {
compatible = "jedec,spi-nor";
reg = <0>;
spi-max-frequency = <25000000>;
partitions {
compatible = "fixed-partitions";
#address-cells = <1>;
#size-cells = <1>;
uboot: partition@0 {
label = "u-boot";
reg = <0x000000 0x020000>;
read-only;
};
partition@20000 {
compatible = "tplink,firmware";
label = "firmware";
reg = <0x020000 0x7d0000>;
};
art: partition@7f0000 {
label = "art";
reg = <0x7f0000 0x010000>;
read-only;
};
};
};
};
&gpio {
gpio_ext_lna0 {
gpio-hog;
gpios = <18 GPIO_ACTIVE_HIGH>;
output-high;
line-name = "tp-link:ext:lna0";
};
gpio_ext_lna1 {
gpio-hog;
gpios = <19 GPIO_ACTIVE_HIGH>;
output-high;
line-name = "tp-link:ext:lna1";
};
};
&wmac {
status = "okay";
mtd-cal-data = <&art 0x1000>;
nvmem-cells = <&macaddr_uboot_1fc00>;
nvmem-cell-names = "mac-address";
};
&eth0 {
status = "okay";
phy-handle = <&swphy0>;
nvmem-cells = <&macaddr_uboot_1fc00>;
nvmem-cell-names = "mac-address";
mac-address-increment = <1>;
};
&eth1 {
status = "okay";
nvmem-cells = <&macaddr_uboot_1fc00>;
nvmem-cell-names = "mac-address";
gmac-config {
device = <&gmac>;
switch-phy-swap = <1>;
};
};
&uboot {
compatible = "nvmem-cells";
#address-cells = <1>;
#size-cells = <1>;
macaddr_uboot_1fc00: macaddr@1fc00 {
reg = <0x1fc00 0x6>;
};
};