ExternalVendorCode/openwrt
1
0
Fork 0
mirror of https://github.com/openwrt/openwrt.git synced 2024-12-20 14:13:16 +00:00
Code Issues Actions 4 Packages Projects Releases Wiki Activity
6d5873a162
openwrt/target/linux/realtek/image/rtl838x.mk
Alexandru Gagniuc 6d5873a162 realtek: add support for TP-Link SG2008P 
Add support for the TP-Link SG2008P switch. This is an RTL8380 based
switch with 802.3af one the first four ports.

Specifications:
---------------
 * SoC:       Realtek RTL8380M
 * Flash:     32 MiB SPI flash (Vendor varies)
 * RAM:       256 MiB (Vendor varies)
 * Ethernet:  8x 10/100/1000 Mbps with PoE on 4 ports
 * Buttons:   1x "Reset" button on front panel
 * Power:     53.5V DC barrel jack
 * UART:      1x serial header, unpopulated
 * PoE:       1x TI TPS23861 I2C PoE controller

Works:
------
  - (8) RJ-45 ethernet ports
  - Switch functions
  - System LED

Not yet enabled:
----------------
  - Power-over-Ethernet (driver works, but doesn't enable "auto" mode)
  - PoE, Link/Act, PoE max and System LEDs

Install via web interface:
-------------------------

Not supported at this time.

Install via serial console/tftp:
--------------------------------

The footprints R27 (0201) and R28 (0402) are not populated. To enable
serial console, 50 ohm resistors should be soldered -- any value from
0 ohm to 50 ohm will work. R27 can be replaced by a solder bridge.

The u-boot firmware drops to a TP-Link specific "BOOTUTIL" shell at
38400 baud. There is no known way to exit out of this shell, and no
way to do anything useful.

Ideally, one would trick the bootloader into flashing the sysupgrade
image first. However, if the image exceeds 6MiB in size, it will not
work. The sysupgrade image can also be flashed. To install OpenWRT:

Prepare a tftp server with:
 1. server address: 192.168.0.146
 2. the image as: "uImage.img"

Power on device, and stop boot by pressing any key.
Once the shell is active:
 1. Ground out the CLK (pin 16) of the ROM (U7)
 2. Select option "3. Start"
 3. Bootloader notes that "The kernel has been damaged!"
 4. Release CLK as sson as bootloader thinks image is corrupted.
 5. Bootloader enters automatic recovery -- details printed on console
 6. Watch as the bootloader flashes and boots OpenWRT.

Blind install via tftp:
-----------------------

This method works when it's not feasible to install a serial header.

Prepare a tftp server with:
 1. server address: 192.168.0.146
 2. the image as: "uImage.img"
 3. Watch network traffic (tcpdump or wireshark works)
 4. Power on the device.
 5. Wait 1-2 seconds then ground out the CLK (pin 16) of the ROM (U7)
 6. When 192.168.0.30 makes tftp requests, release pin 16
 7. Wait 2-3 minutes for device to auto-flash and boot OpenWRT

Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
2022-08-13 19:59:47 +02:00

265 lines
6.1 KiB
Makefile
Raw Blame History

# SPDX-License-Identifier: GPL-2.0-only
define Device/allnet_all-sg8208m
SOC := rtl8382
IMAGE_SIZE := 7168k
DEVICE_VENDOR := ALLNET
DEVICE_MODEL := ALL-SG8208M
UIMAGE_MAGIC := 0x00000006
UIMAGE_NAME := 2.2.2.0
endef
TARGET_DEVICES += allnet_all-sg8208m
define Device/d-link_dgs-1210
SOC := rtl8382
IMAGE_SIZE := 13824k
DEVICE_VENDOR := D-Link
DLINK_KERNEL_PART_SIZE := 1572864
KERNEL := kernel-bin | append-dtb | gzip | uImage gzip | dlink-cameo
CAMEO_KERNEL_PART := 2
CAMEO_ROOTFS_PART := 3
CAMEO_CUSTOMER_SIGNATURE := 2
CAMEO_BOARD_VERSION := 32
IMAGES += factory_image1.bin
IMAGE/factory_image1.bin := append-kernel | pad-to 64k | \
append-rootfs | pad-rootfs | pad-to 16 | check-size | \
dlink-version | dlink-headers
endef
define Device/d-link_dgs-1210-10p
$(Device/d-link_dgs-1210)
DEVICE_MODEL := DGS-1210-10P
DEVICE_PACKAGES += lua-rs232
endef
TARGET_DEVICES += d-link_dgs-1210-10p
define Device/d-link_dgs-1210-16
$(Device/d-link_dgs-1210)
DEVICE_MODEL := DGS-1210-16
endef
TARGET_DEVICES += d-link_dgs-1210-16
define Device/d-link_dgs-1210-20
$(Device/d-link_dgs-1210)
DEVICE_MODEL := DGS-1210-20
endef
TARGET_DEVICES += d-link_dgs-1210-20
define Device/d-link_dgs-1210-28
$(Device/d-link_dgs-1210)
DEVICE_MODEL := DGS-1210-28
endef
TARGET_DEVICES += d-link_dgs-1210-28
# The "IMG-" uImage name allows flashing the iniramfs from the vendor Web UI.
# Avoided for sysupgrade, as the vendor FW would do an incomplete flash.
define Device/engenius_ews2910p
SOC := rtl8380
IMAGE_SIZE := 8192k
DEVICE_VENDOR := EnGenius
DEVICE_MODEL := EWP2910P
UIMAGE_MAGIC := 0x03802910
KERNEL_INITRAMFS := kernel-bin | append-dtb | gzip | \
uImage gzip -n 'IMG-0.00.00-c0.0.00'
endef
TARGET_DEVICES += engenius_ews2910p
define Device/hpe_1920-8g
$(Device/hpe_1920)
SOC := rtl8380
DEVICE_MODEL := 1920-8G (JG920A)
H3C_DEVICE_ID := 0x00010023
endef
TARGET_DEVICES += hpe_1920-8g
define Device/hpe_1920-16g
$(Device/hpe_1920)
SOC := rtl8382
DEVICE_MODEL := 1920-16G (JG923A)
H3C_DEVICE_ID := 0x00010026
endef
TARGET_DEVICES += hpe_1920-16g
define Device/hpe_1920-24g
$(Device/hpe_1920)
SOC := rtl8382
DEVICE_MODEL := 1920-24G (JG924A)
H3C_DEVICE_ID := 0x00010027
endef
TARGET_DEVICES += hpe_1920-24g
define Device/inaba_aml2-17gp
SOC := rtl8382
IMAGE_SIZE := 13504k
DEVICE_VENDOR := INABA
DEVICE_MODEL := Abaniact AML2-17GP
UIMAGE_MAGIC := 0x83800000
endef
TARGET_DEVICES += inaba_aml2-17gp
define Device/iodata_bsh-g24mb
SOC := rtl8382
IMAGE_SIZE := 13696k
DEVICE_VENDOR := I-O DATA
DEVICE_MODEL := BSH-G24MB
UIMAGE_MAGIC := 0x83800013
endef
TARGET_DEVICES += iodata_bsh-g24mb
define Device/netgear_gs108t-v3
$(Device/netgear_nge)
DEVICE_MODEL := GS108T
DEVICE_VARIANT := v3
endef
TARGET_DEVICES += netgear_gs108t-v3
define Device/netgear_gs110tpp-v1
$(Device/netgear_nge)
DEVICE_MODEL := GS110TPP
DEVICE_VARIANT := v1
endef
TARGET_DEVICES += netgear_gs110tpp-v1
define Device/netgear_gs308t-v1
$(Device/netgear_nge)
DEVICE_MODEL := GS308T
DEVICE_VARIANT := v1
UIMAGE_MAGIC := 0x4e474335
endef
TARGET_DEVICES += netgear_gs308t-v1
define Device/netgear_gs310tp-v1
$(Device/netgear_nge)
DEVICE_MODEL := GS310TP
DEVICE_VARIANT := v1
UIMAGE_MAGIC := 0x4e474335
DEVICE_PACKAGES += lua-rs232
endef
TARGET_DEVICES += netgear_gs310tp-v1
define Device/panasonic_m16eg-pn28160k
SOC := rtl8382
IMAGE_SIZE := 16384k
DEVICE_VENDOR := Panasonic
DEVICE_MODEL := Switch-M16eG
DEVICE_VARIANT := PN28160K
DEVICE_PACKAGES := kmod-i2c-mux-pca954x
endef
TARGET_DEVICES += panasonic_m16eg-pn28160k
define Device/panasonic_m24eg-pn28240k
SOC := rtl8382
IMAGE_SIZE := 16384k
DEVICE_VENDOR := Panasonic
DEVICE_MODEL := Switch-M24eG
DEVICE_VARIANT := PN28240K
DEVICE_PACKAGES := kmod-i2c-mux-pca954x
endef
TARGET_DEVICES += panasonic_m24eg-pn28240k
define Device/panasonic_m8eg-pn28080k
SOC := rtl8380
IMAGE_SIZE := 16384k
DEVICE_VENDOR := Panasonic
DEVICE_MODEL := Switch-M8eG
DEVICE_VARIANT := PN28080K
DEVICE_PACKAGES := kmod-i2c-mux-pca954x
endef
TARGET_DEVICES += panasonic_m8eg-pn28080k
define Device/tplink_sg2008p-v1
SOC := rtl8380
KERNEL_SIZE := 6m
IMAGE_SIZE := 26m
DEVICE_VENDOR := TP-Link
DEVICE_MODEL := SG2008P
DEVICE_VARIANT := v1
DEVICE_PACKAGES := kmod-hwmon-tps23861
endef
TARGET_DEVICES += tplink_sg2008p-v1
define Device/zyxel_gs1900
SOC := rtl8380
IMAGE_SIZE := 6976k
DEVICE_VENDOR := ZyXEL
UIMAGE_MAGIC := 0x83800000
KERNEL_INITRAMFS := kernel-bin | append-dtb | gzip | zyxel-vers | \
uImage gzip
endef
define Device/zyxel_gs1900-10hp
$(Device/zyxel_gs1900)
DEVICE_MODEL := GS1900-10HP
ZYXEL_VERS := AAZI
endef
TARGET_DEVICES += zyxel_gs1900-10hp
define Device/zyxel_gs1900-16
$(Device/zyxel_gs1900)
SOC := rtl8382
DEVICE_MODEL := GS1900-16
ZYXEL_VERS := AAHJ
endef
TARGET_DEVICES += zyxel_gs1900-16
define Device/zyxel_gs1900-8
$(Device/zyxel_gs1900)
DEVICE_MODEL := GS1900-8
ZYXEL_VERS := AAHH
endef
TARGET_DEVICES += zyxel_gs1900-8
define Device/zyxel_gs1900-8hp-v1
$(Device/zyxel_gs1900)
DEVICE_MODEL := GS1900-8HP
DEVICE_VARIANT := v1
ZYXEL_VERS := AAHI
DEVICE_PACKAGES += lua-rs232
endef
TARGET_DEVICES += zyxel_gs1900-8hp-v1
define Device/zyxel_gs1900-8hp-v2
$(Device/zyxel_gs1900)
DEVICE_MODEL := GS1900-8HP
DEVICE_VARIANT := v2
ZYXEL_VERS := AAHI
DEVICE_PACKAGES += lua-rs232
endef
TARGET_DEVICES += zyxel_gs1900-8hp-v2
define Device/zyxel_gs1900-24-v1
$(Device/zyxel_gs1900)
SOC := rtl8382
DEVICE_MODEL := GS1900-24
DEVICE_VARIANT := v1
ZYXEL_VERS := AAHL
endef
TARGET_DEVICES += zyxel_gs1900-24-v1
define Device/zyxel_gs1900-24e
$(Device/zyxel_gs1900)
SOC := rtl8382
DEVICE_MODEL := GS1900-24E
ZYXEL_VERS := AAHK
endef
TARGET_DEVICES += zyxel_gs1900-24e
define Device/zyxel_gs1900-24hp-v1
$(Device/zyxel_gs1900)
SOC := rtl8382
DEVICE_MODEL := GS1900-24HP
DEVICE_VARIANT := v1
ZYXEL_VERS := AAHM
endef
TARGET_DEVICES += zyxel_gs1900-24hp-v1
define Device/zyxel_gs1900-24hp-v2
$(Device/zyxel_gs1900)
SOC := rtl8382
DEVICE_MODEL := GS1900-24HP
DEVICE_VARIANT := v2
ZYXEL_VERS := ABTP
endef
TARGET_DEVICES += zyxel_gs1900-24hp-v2
Reference in New Issue View Git Blame Copy Permalink