openwrt/target/linux/bcm53xx/patches-5.10/081-next-ARM_dts_BCM53015-add-mr26.patch
Christian Lamparter e37ba80633 bcm53xx: add support for Meraki MR26
Meraki MR26 is an EOL wireless access point featuring a
PoE ethernet port and two dual-band 3x3 MIMO 802.11n
radios and 1x1 dual-band WIFI dedicated to scanning.

Thank you Amir for the unit and PSU.

Hardware info:
SOC   : Broadcom BCM53015A1KFEBG (dual-core Cortex-A9 CPU at 800 MHz)
RAM   : SK hynix Inc. H5TQ1G63EFR, 1 Gbit DDR3 SDRAM = 128 MiB
NAND  : Spansion S34ML01G100TF100, 1 Gbit SLC NAND Flash = 128 MiB
ETH   : 1 GBit Ethernet Port - PoE
WIFI1 : Broadcom BCM43431KMLG, BCM43431 802.11 abgn
WIFI1 : Broadcom BCM43431KMLG, BCM43431 802.11 abgn
WIFI3 : Broadcom BCM43428 abgn (1x1:1 - id: 43428)
BUTTON: one reset button
LEDS  : RGB-LED
MISC  : Atmel AT24C64 8KiB EEPROM (i2c - seems empty)
      : Ti INA219 26V, 12-bit, i2c output current/voltage/power monitor
      : TPS23754, High Power/High Efficiency PoE Interface+DC/DC Controller

SERIAL:
	WARNING: The serial port needs a TTL/RS-232 3V3 level converter!
	The Serial setting is 115200-8-N-1. The board has a populated
	right angle 1x4 0.1" pinheader.
	The pinout is: VCC (next to J3, has little white arrow), RX, TX, GND.

This flashing procedure for the MR26 was tested with firmware:
    "22-143410M-gf25cbf5a-asa".
    U-Boot 2012.10-00063-g83f9fe4 (Jun 04 2014 - 21:22:39)

A guide how to open up the device is available on the wiki:
<https://openwrt.org/toh/meraki/mr26>

Notes:
 - The WIFI do work to a degree. Limited to 802.11bg in the 2.4GHz band.
 - the WIFI macs are made up.

0. Create a separate Ethernet LAN which can't have access to the internet.
   Ideally use 192.168.1.2 for your PC. The new OpenWrt firmware will setup
   the network via DHCP Discovery, so make sure your PC is running
   a DHCP-Server (i.e.: dnsmasq)
   '# dnsmasq -i eth# -F 192.168.1.5,192.168.1.50
   Download the openwrt-meraki-mr26 initramfs file from openwrt.org and
   rename it to something simple like mr26.bin. Then put it into the tftp's
   server directory.

1. Disassemble the MR26 device by removing all screws (4 screws are located
   under the 4 rubber feets!) and prying open the plastic covers without
   breaking the plastic retention clips. Once inside, remove the plastic
   back casing. Be careful, there some "hidden" retention clips on both
   sides of the LAN port, you need a light to see those. Next, you want to
   remove all the screws on the outer metal shielding to get to the PCB.
   It's not necessary to remove the antennas!

2. Connect the serial cable to the serial header and Ethernet patch cable
   to the device.

4. Before connecting the power, get ready flood the serial console program
   with the magic:   xyzzy  . This is necessary in order to get into the
   u-boot prompt. Once Ready: connect power cable.

5. If you don't get the "u-boot>" prompt within the first few seconds,
   you have to disconnect and reconnect the power cable and try again.

6. In the u-boot prompt enter:

   setenv ipaddr 192.168.1.4
   setenv serverip 192.168.1.2
   tftpboot ${meraki_loadaddr} mr26.bin; bootm

   this will boot a in-ram-only OpenWrt image.

7. Once it booted use sysupgrade to permanently install OpenWrt.
   To do this: Download the latest sysupgrade.bin file and move
   it to the device. Then use sysupgrade *sysupgrade.bin to install it.

    WARNING: DO NOT DELETE the "storage" ubi volume!

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2022-07-15 15:21:44 +02:00

243 lines
6.1 KiB
Diff

From 935327a73553001f8d81375c76985d05f604507f Mon Sep 17 00:00:00 2001
From: Christian Lamparter <chunkeey@gmail.com>
Date: Sat, 18 Jun 2022 00:00:29 +0200
Subject: [PATCH] ARM: dts: BCM5301X: Add DT for Meraki MR26
Meraki MR26 is an EOL wireless access point featuring a
PoE ethernet port and two dual-band 3x3 MIMO 802.11n
radios and 1x1 dual-band WIFI dedicated to scanning.
Thank you Amir for the unit and PSU.
Hardware info:
SOC : Broadcom BCM53015A1KFEBG (dual-core Cortex-A9 CPU at 800 MHz)
RAM : SK Hynix Inc. H5TQ1G63EFR, 1 GBit DDR3 SDRAM = 128 MiB
NAND : Spansion S34ML01G100TF100, 1 GBit SLC NAND Flash = 128 MiB
ETH : 1 GBit Ethernet Port - PoE (TPS23754 PoE Interface)
WIFI0 : Broadcom BCM43431KMLG, BCM43431 802.11 abgn (3x3:3)
WIFI1 : Broadcom BCM43431KMLG, BCM43431 802.11 abgn (3x3:3)
WIFI2 : Broadcom BCM43428 "Air Marshal" 802.11 abgn (1x1:1)
BUTTON: One reset key behind a small hole next to the Ethernet Port
LEDS : One amber (fault), one white (indicator) LED, separate RGB-LED
MISC : Atmel AT24C64 8KiB EEPROM i2c
: Ti INA219 26V, 12-bit, i2c output current/voltage/power monitor
SERIAL:
WARNING: The serial port needs a TTL/RS-232 3V3 level converter!
The Serial setting is 115200-8-N-1. The board has a populated
right angle 1x4 0.1" pinheader.
The pinout is: VCC (next to J3, has the pin 1 indicator), RX, TX, GND.
Odd stuff:
- uboot does not support lzma compression, but gzip'd uImage/DTB work.
- uboot claims to support FIT, but fails to pass the DTB to the kernel.
Appending the dtb after the kernel image works.
- RGB-controller is supported through an external userspace program.
- The ubi partition contains a "board-config" volume. It stores the
MAC Address (0x66 in binary) and Serial No. (0x7c alpha-numerical).
- SoC's temperature sensor always reports that it is on fire.
This causes the system to immediately shutdown! Looking at reported
"418 degree Celsius" suggests that this sensor is not working.
WIFI:
b43 is able to initialize all three WIFIs @ 802.11bg.
| b43-phy0: Broadcom 43431 WLAN found (core revision 29)
| bcma-pci-bridge 0000:01:00.0: bus1: Switched to core: 0x812
| b43-phy0: Found PHY: Analog 9, Type 7 (HT), Revision 1
| b43-phy0: Found Radio: Manuf 0x17F, ID 0x2059, Revision 0, Version 1
| b43-phy0 warning: 5 GHz band is unsupported on this PHY
| b43-phy1: Broadcom 43431 WLAN found (core revision 29)
| bcma-pci-bridge 0001:01:00.0: bus2: Switched to core: 0x812
| b43-phy1: Found PHY: Analog 9, Type 7 (HT), Revision 1
| b43-phy1: Found Radio: Manuf 0x17F, ID 0x2059, Revision 0, Version 1
| b43-phy1 warning: 5 GHz band is unsupported on this PHY
| b43-phy2: Broadcom 43228 WLAN found (core revision 30)
| bcma-pci-bridge 0002:01:00.0: bus3: Switched to core: 0x812
| b43-phy2: Found PHY: Analog 9, Type 4 (N), Revision 16
| b43-phy2: Found Radio: Manuf 0x17F, ID 0x2057, Revision 9, Version 1
| Broadcom 43xx driver loaded [ Features: NL ]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
---
--- /dev/null
+++ b/arch/arm/boot/dts/bcm53015-meraki-mr26.dts
@@ -0,0 +1,166 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Broadcom BCM470X / BCM5301X ARM platform code.
+ * DTS for Meraki MR26 / Codename: Venom
+ *
+ * Copyright (C) 2022 Christian Lamparter <chunkeey@gmail.com>
+ */
+
+/dts-v1/;
+
+#include "bcm4708.dtsi"
+#include "bcm5301x-nand-cs0-bch8.dtsi"
+#include <dt-bindings/leds/common.h>
+
+/ {
+ compatible = "meraki,mr26", "brcm,bcm53015", "brcm,bcm4708";
+ model = "Meraki MR26";
+
+ memory@0 {
+ reg = <0x00000000 0x08000000>;
+ device_type = "memory";
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ led-0 {
+ function = LED_FUNCTION_FAULT;
+ color = <LED_COLOR_ID_AMBER>;
+ gpios = <&chipcommon 13 GPIO_ACTIVE_HIGH>;
+ panic-indicator;
+ };
+ led-1 {
+ function = LED_FUNCTION_INDICATOR;
+ color = <LED_COLOR_ID_WHITE>;
+ gpios = <&chipcommon 12 GPIO_ACTIVE_HIGH>;
+ };
+ };
+
+ keys {
+ compatible = "gpio-keys";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ key-restart {
+ label = "Reset";
+ linux,code = <KEY_RESTART>;
+ gpios = <&chipcommon 11 GPIO_ACTIVE_LOW>;
+ };
+ };
+};
+
+&uart0 {
+ clock-frequency = <50000000>;
+ /delete-property/ clocks;
+};
+
+&uart1 {
+ status = "disabled";
+};
+
+&gmac0 {
+ status = "okay";
+};
+
+&gmac1 {
+ status = "disabled";
+};
+&gmac2 {
+ status = "disabled";
+};
+&gmac3 {
+ status = "disabled";
+};
+
+&nandcs {
+ nand-ecc-algo = "hw";
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <0x1>;
+ #size-cells = <0x1>;
+
+ partition@0 {
+ label = "u-boot";
+ reg = <0x0 0x200000>;
+ read-only;
+ };
+
+ partition@200000 {
+ label = "u-boot-env";
+ reg = <0x200000 0x200000>;
+ /* empty */
+ };
+
+ partition@400000 {
+ label = "u-boot-backup";
+ reg = <0x400000 0x200000>;
+ /* empty */
+ };
+
+ partition@600000 {
+ label = "u-boot-env-backup";
+ reg = <0x600000 0x200000>;
+ /* empty */
+ };
+
+ partition@800000 {
+ label = "ubi";
+ reg = <0x800000 0x7780000>;
+ };
+ };
+};
+
+&srab {
+ status = "okay";
+
+ ports {
+ port@0 {
+ reg = <0>;
+ label = "poe";
+ };
+
+ port@5 {
+ reg = <5>;
+ label = "cpu";
+ ethernet = <&gmac0>;
+
+ fixed-link {
+ speed = <1000>;
+ duplex-full;
+ };
+ };
+ };
+};
+
+&i2c0 {
+ status = "okay";
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinmux_i2c>;
+
+ clock-frequency = <100000>;
+
+ ina219@40 {
+ compatible = "ti,ina219"; /* PoE power */
+ reg = <0x40>;
+ shunt-resistor = <60000>; /* = 60 mOhms */
+ };
+
+ eeprom@56 {
+ compatible = "atmel,24c64";
+ reg = <0x56>;
+ pagesize = <32>;
+ read-only;
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ /* it's empty */
+ };
+};
+
+&thermal {
+ status = "disabled";
+ /* does not work, reads 418 degree Celsius */
+};
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -129,6 +129,7 @@ dtb-$(CONFIG_ARCH_BCM_5301X) += \
bcm47094-luxul-xwr-3150-v1.dtb \
bcm47094-netgear-r8500.dtb \
bcm47094-phicomm-k3.dtb \
+ bcm53015-meraki-mr26.dtb \
bcm53016-meraki-mr32.dtb \
bcm94708.dtb \
bcm94709.dtb \