openwrt/target/linux/ramips/dts/DAP-1522-A1.dts
Alex Maclean 6031ab345d ramips: move partitions into partition table node
Starting with kernel 4.4, the use of partitions as direct subnodes of the
mtd device is discouraged and only supported for backward compatiblity
reasons.

Signed-off-by: Alex Maclean <monkeh@monkeh.net>
2018-08-04 08:39:35 +02:00

146 lines
2.3 KiB
Plaintext

/dts-v1/;
#include "rt2880.dtsi"
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>
/ {
compatible = "dlink,dap-1522-a1", "ralink,rt2880-soc";
model = "D-Link DAP-1522 A1";
aliases {
led-status = &led_status;
};
cfi@bc400000 {
compatible = "cfi-flash";
reg = <0xbc400000 0x800000>;
bank-width = <2>;
device-width = <2>;
partitions {
compatible = "fixed-partitions";
#address-cells = <1>;
#size-cells = <1>;
partition@0 {
label = "uboot";
reg = <0x0 0x30000>;
read-only;
};
factory: partition@30000 {
label = "factory";
reg = <0x30000 0x10000>;
read-only;
};
partition@40000 {
label = "firmware";
reg = <0x40000 0x3a0000>;
};
};
};
rtl8366s {
compatible = "realtek,rtl8366s";
gpio-sda = <&gpio0 1 GPIO_ACTIVE_HIGH>;
gpio-sck = <&gpio0 2 GPIO_ACTIVE_HIGH>;
};
gpio-keys-polled {
compatible = "gpio-keys-polled";
poll-interval = <100>;
reset {
label = "reset";
gpios = <&gpio0 9 GPIO_ACTIVE_LOW>;
linux,code = <KEY_RESTART>;
};
wps {
label = "wps";
gpios = <&gpio2 16 GPIO_ACTIVE_LOW>;
linux,code = <KEY_WPS_BUTTON>;
};
ap {
label = "ap";
gpios = <&gpio2 13 GPIO_ACTIVE_LOW>;
linux,code = <BTN_0>;
linux,input-type = <EV_SW>;
};
bridge {
label = "bridge";
gpios = <&gpio2 14 GPIO_ACTIVE_LOW>;
linux,code = <BTN_1>;
linux,input-type = <EV_SW>;
};
};
gpio-leds {
compatible = "gpio-leds";
wps {
label = "dap-1522-a1:blue:wps";
gpios = <&gpio2 17 GPIO_ACTIVE_LOW>;
};
ap {
label = "dap-1522-a1:blue:ap";
gpios = <&gpio2 18 GPIO_ACTIVE_LOW>;
};
sta {
label = "dap-1522-a1:red:sta";
gpios = <&gpio2 19 GPIO_ACTIVE_LOW>;
};
led_status: status {
label = "dap-1522-a1:blue:status";
gpios = <&gpio2 20 GPIO_ACTIVE_LOW>;
};
};
};
&gpio0 {
status = "okay";
};
&gpio2 {
status = "okay";
};
&pinctrl {
state_default: pinctrl0 {
gpio {
ralink,group = "i2c", "uartlite", "pci";
ralink,function = "gpio";
};
};
};
&ethernet {
status = "okay";
mtd-mac-address = <&factory 0x2004>;
port@0 {
mediatek,fixed-link = <1000 1 1 1>;
};
mdio-bus {
status = "okay";
phy0: ethernet-phy@0 {
phy-mode = "mii";
reg = <0>;
};
};
};
&wmac {
ralink,mtd-eeprom = <&factory 0x2000>;
};