mirror of
https://github.com/openwrt/openwrt.git
synced 2024-12-19 21:58:04 +00:00
86e7353bff
TP-Link Archer C20 v5 is a router with 5-port FE switch and non-detachable antennas. It's based on MediaTek MT7628N+MT7610EN. Specification: - MediaTek MT7628N/N (580 Mhz) - 64 MB of RAM - 8 MB of FLASH - 2T2R 2.4 GHz and 1T1R 5 GHz - 5x 10/100 Mbps Ethernet - 3x external, non-detachable antennas - UART (J1) header on PCB (115200 8n1) - 7x LED (GPIO-controlled*), 2x button, power input switch * WAN LED in this devices is a dual-color, dual-leads type which isn't (fully) supported by gpio-leds driver. This type of LED requires both GPIOs state change at the same time to select color or turn it off. For now, we support/use only the green part of the LED. Create Factory image -------------------- As all installation methods require a U-Boot to be integrated into the Image (and we do not ship one with the image) we are not able to create an image in the OpenWRT build-process. Download a TP-Link image from their Website and a OpenWRT sysupgrade image for the device and build yourself a factory image like following: TP-Link image: tpl.bin OpenWRT sysupgrade image: owrt.bin > dd if=tpl.bin of=boot.bin bs=131584 count=1 > cat owrt.bin >> boot.bin Installing via Web-UI --------------------- Upload the boot.bin via TP-Links firmware upgrade tool in the web-interface. Installing via Recovery ----------------------- Activate Web-Recovery by beginning the upgrade Process with a Firmware-Image from TP-Link. After starting the Firmware Upgrade, wait ~3 seconds (When update status is switching to 0%), then disconnect the power supply from the device. Upgrade flag (which activates Web-Recovery) is written before the OS-image is touched and removed after write is succesfull, so this procedure should be safe. Plug the power back in. It will come up in Recovery-Mode on 192.168.0.1. When active, all LEDs but the WPS LED are off. Remeber to assign yourself a static IP-address as DHCP is not active in this mode. The boot.bin can now be uploaded and flashed using the web-recovery. Installing via TFTP ------------------- Prepare an image like following (Filenames from factory image steps apply here) > dd if=/dev/zero of=tp_recovery.bin bs=196608 count=1 > dd if=tpl.bin of=tmp.bin bs=131584 count=1 > dd if=tmp.bin of=boot.bin bs=512 skip=1 > cat boot.bin >> tp_recovery.bin > cat owrt.bin >> tp_recovery.bin Place tp_recovery.bin in root directory of TFTP server and listen on 192.168.0.66/24. Connect router LAN ports with your computer and power up the router while pressing the reset button. The router will download the image via tftp and after ~1 Minute reboot into OpenWRT. U-Boot CLI ---------- U-Boot CLI can be activated by holding down '4' on bootup. Dual U-Boot ----------- This is TP-Link MediaTek device with a split-uboot feature design like a TP-Link Archer C50 v4. The first (factory-uboot) provides recovery via TFTP and HTTP, jumping straight into the second (firmware-uboot) if no recovery needs to be performed. The firmware-uboot unpacks and executed the kernel. Web-Recovery ------------ TP-Link integrated a new Web-Recovery like the one on the Archer C7v4 / TL-WR1043v5 / Archer C50v4. Stock-firmware sets a flag in the "romfile" partition before beginning to write and removes it afterwards. If the router boots with this flag set, bootloader will automatically start Web-recovery and listens on 192.168.0.1. This way, the vendor-firmware or an OpenWRT factory image can be written. By doing the same while performing sysupgrade, we can take advantage of the Web-recovery in OpenWRT. It is important to note that Web-Recovery is only based on this flag. It can't detect e.g. a crashing kernel or other means. Once activated it won't boot the OS before a recovery action (either via TFTP or HTTP) is performed. This recovery-mode is indicated by an illuminated WPS-LED on boot. Signed-off-by: Maxim Anisimov <maxim.anisimov.ua@gmail.com> [adjust some node names for LEDs in DTS] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> |
||
|---|---|---|
| .. | ||
| platform.sh | ||