mirror of
https://github.com/openwrt/openwrt.git
synced 2024-12-29 18:19:02 +00:00
3a4b751110
The uart node is enabled on all devices except one (GL-USB150 *). Thus, let's not have a few hundred nodes to enable it, but do not disable it in the first place. Where the majority of devices is using it, also move the serial0 alias to the DTSI. *) Since GL-USB150 even defines serial0 alias, the missing uart is probably just a mistake. Anyway, disable it for now so this patch stays cosmetic. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
130 lines
2.0 KiB
Plaintext
130 lines
2.0 KiB
Plaintext
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
|
|
|
#include "qca955x.dtsi"
|
|
|
|
#include <dt-bindings/gpio/gpio.h>
|
|
#include <dt-bindings/input/input.h>
|
|
|
|
/ {
|
|
compatible = "mikrotik,routerboard-wap-g-5hact2hnd", "qca,qca9556";
|
|
model = "MikroTik RouterBOARD wAP G-5HacT2HnD";
|
|
|
|
aliases {
|
|
mdio-gpio1 = &mdio2;
|
|
serial0 = &uart;
|
|
};
|
|
|
|
keys {
|
|
compatible = "gpio-keys";
|
|
|
|
reset {
|
|
label = "reset";
|
|
linux,code = <KEY_RESTART>;
|
|
gpios = <&gpio 1 GPIO_ACTIVE_LOW>;
|
|
debounce-interval = <60>;
|
|
};
|
|
};
|
|
|
|
mdio2: mdio {
|
|
compatible = "virtual,mdio-gpio";
|
|
|
|
gpios = <&gpio 12 GPIO_ACTIVE_HIGH>, /* MDC */
|
|
<&gpio 11 GPIO_ACTIVE_HIGH>; /* MDIO */
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
|
|
phy0: ethernet-phy@0 {
|
|
reg = <0>;
|
|
device_type = "ethernet-phy";
|
|
|
|
phy-mode = "sgmii";
|
|
|
|
at803x-override-sgmii-link-check;
|
|
};
|
|
};
|
|
};
|
|
|
|
ð1 {
|
|
status = "okay";
|
|
|
|
pll-data = <0x03000101 0x80000101 0x80001313>;
|
|
phy-handle = <&phy0>;
|
|
|
|
qca955x-sgmii-fixup;
|
|
|
|
gmac-config {
|
|
device = <&gmac>;
|
|
};
|
|
};
|
|
|
|
&spi {
|
|
status = "okay";
|
|
|
|
flash@0 {
|
|
compatible = "jedec,spi-nor";
|
|
reg = <0>;
|
|
spi-max-frequency = <40000000>;
|
|
|
|
partitions {
|
|
compatible = "fixed-partitions";
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
|
|
partition@0 {
|
|
label = "RouterBoot";
|
|
reg = <0x0 0x20000>;
|
|
read-only;
|
|
compatible = "mikrotik,routerboot-partitions";
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
|
|
partition@0 {
|
|
label = "bootloader1";
|
|
reg = <0x0 0x0>;
|
|
read-only;
|
|
};
|
|
|
|
hard_config: hard_config {
|
|
read-only;
|
|
};
|
|
|
|
bios {
|
|
size = <0x1000>;
|
|
read-only;
|
|
};
|
|
|
|
partition@10000 {
|
|
label = "bootloader2";
|
|
reg = <0x10000 0x0>;
|
|
read-only;
|
|
};
|
|
|
|
soft_config {
|
|
label = "soft_config";
|
|
};
|
|
};
|
|
|
|
partition@20000 {
|
|
compatible = "mikrotik,minor";
|
|
label = "firmware";
|
|
reg = <0x020000 0xfe0000>;
|
|
};
|
|
};
|
|
};
|
|
};
|
|
|
|
&wmac {
|
|
status = "okay";
|
|
|
|
qca,no-eeprom;
|
|
};
|
|
|
|
&pcie0 {
|
|
status = "okay";
|
|
|
|
wifi@0,0 {
|
|
compatible = "qcom,ath10k";
|
|
reg = <0 0 0 0 0>;
|
|
};
|
|
};
|