mirror of
https://github.com/openwrt/openwrt.git
synced 2024-12-30 10:39:04 +00:00
3a4b751110
The uart node is enabled on all devices except one (GL-USB150 *). Thus, let's not have a few hundred nodes to enable it, but do not disable it in the first place. Where the majority of devices is using it, also move the serial0 alias to the DTSI. *) Since GL-USB150 even defines serial0 alias, the missing uart is probably just a mistake. Anyway, disable it for now so this patch stays cosmetic. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
160 lines
2.6 KiB
Plaintext
160 lines
2.6 KiB
Plaintext
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
|
|
|
#include "qca956x.dtsi"
|
|
|
|
#include <dt-bindings/gpio/gpio.h>
|
|
#include <dt-bindings/input/input.h>
|
|
|
|
/ {
|
|
compatible = "avm,fritz4020", "qca,qca9560";
|
|
model = "AVM FRITZ!Box 4020";
|
|
|
|
aliases {
|
|
led-boot = &led_power;
|
|
led-failsafe = &led_info_red;
|
|
led-running = &led_power;
|
|
led-upgrade = &led_info_red;
|
|
};
|
|
|
|
led_spi {
|
|
compatible = "spi-gpio";
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
|
|
sck-gpios = <&gpio 20 GPIO_ACTIVE_HIGH>;
|
|
mosi-gpios = <&gpio 19 GPIO_ACTIVE_HIGH>;
|
|
num-chipselects = <0>;
|
|
|
|
led_gpio: led_gpio@0 {
|
|
compatible = "fairchild,74hc595";
|
|
reg = <0>;
|
|
gpio-controller;
|
|
#gpio-cells = <2>;
|
|
registers-number = <1>;
|
|
spi-max-frequency = <10000000>;
|
|
|
|
gpio_latch_bit {
|
|
gpio-hog;
|
|
gpios = <7 GPIO_ACTIVE_HIGH>;
|
|
output-high;
|
|
line-name = "gpio-latch-bit";
|
|
};
|
|
};
|
|
};
|
|
|
|
leds {
|
|
compatible = "gpio-leds";
|
|
|
|
led_power: power {
|
|
label = "green:power";
|
|
gpios = <&led_gpio 2 GPIO_ACTIVE_LOW>;
|
|
default-state = "on";
|
|
};
|
|
|
|
wlan {
|
|
label = "green:wlan";
|
|
gpios = <&led_gpio 3 GPIO_ACTIVE_LOW>;
|
|
linux,default-trigger = "phy0tpt";
|
|
};
|
|
|
|
lan {
|
|
label = "green:lan";
|
|
gpios = <&led_gpio 0 GPIO_ACTIVE_LOW>;
|
|
};
|
|
|
|
wan {
|
|
label = "green:wan";
|
|
gpios = <&led_gpio 4 GPIO_ACTIVE_LOW>;
|
|
};
|
|
|
|
info {
|
|
label = "green:info";
|
|
gpios = <&led_gpio 6 GPIO_ACTIVE_LOW>;
|
|
};
|
|
|
|
led_info_red: info_red {
|
|
label = "red:info";
|
|
gpios = <&led_gpio 1 GPIO_ACTIVE_LOW>;
|
|
};
|
|
};
|
|
|
|
keys {
|
|
compatible = "gpio-keys";
|
|
|
|
wps {
|
|
label = "WPS button";
|
|
linux,code = <KEY_WPS_BUTTON>;
|
|
gpios = <&gpio 2 GPIO_ACTIVE_LOW>;
|
|
};
|
|
|
|
wlan {
|
|
label = "WLAN button";
|
|
linux,code = <KEY_RFKILL>;
|
|
gpios = <&gpio 21 GPIO_ACTIVE_LOW>;
|
|
};
|
|
};
|
|
};
|
|
|
|
&spi {
|
|
status = "okay";
|
|
|
|
flash@0 {
|
|
compatible = "jedec,spi-nor";
|
|
reg = <0>;
|
|
spi-max-frequency = <25000000>;
|
|
|
|
partitions {
|
|
compatible = "fixed-partitions";
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
|
|
partition@0 {
|
|
label = "urlader";
|
|
reg = <0x000000 0x020000>;
|
|
read-only;
|
|
};
|
|
|
|
partition@1 {
|
|
compatible = "avm,eva-firmware";
|
|
label = "firmware";
|
|
reg = <0x020000 0xee0000>;
|
|
};
|
|
|
|
partition@2 {
|
|
label = "tffs (1)";
|
|
reg = <0xf00000 0x080000>;
|
|
read-only;
|
|
};
|
|
|
|
partition@3 {
|
|
label = "tffs (2)";
|
|
reg = <0xf80000 0x080000>;
|
|
read-only;
|
|
};
|
|
};
|
|
};
|
|
};
|
|
|
|
ð0 {
|
|
status = "okay";
|
|
|
|
phy-handle = <&swphy0>;
|
|
|
|
gmac-config {
|
|
device = <&gmac>;
|
|
|
|
switch-phy-addr-swap = <1>;
|
|
switch-phy-swap = <1>;
|
|
};
|
|
};
|
|
|
|
ð1 {
|
|
status = "okay";
|
|
};
|
|
|
|
&wmac {
|
|
status = "okay";
|
|
|
|
qca,no-eeprom;
|
|
};
|