ExternalVendorCode/openwrt
1
0
Fork 0
mirror of https://github.com/openwrt/openwrt.git synced 2024-12-22 06:57:57 +00:00
Code Issues Actions 1 Packages Projects Releases Wiki Activity
670dedbbd7
openwrt/target/linux/mediatek/image/filogic.mk
Pietro Ameruoso 22d7148689 mediatek: add support for Zyxel EX5601-T0 router 
Zyxel EX5601-T0 specifics
--------------
The operator specific firmware running on the Zyxel branded
EX5601-T0 includes  U-Boot modifications affecting the OpenWrt
installation.

Partition Table
| dev  | size     | erasesize | name          |
| ---- | -------- | --------- | ------------- |
| mtd0 | 20000000 | 00040000  | "spi0.1"      |
| mtd1 | 00100000 | 00040000  | "BL2"         |
| mtd2 | 00080000 | 00040000  | "u-boot-env"  |
| mtd3 | 00200000 | 00040000  | "Factory"     |
| mtd4 | 001c0000 | 00040000  | "FIP"         |
| mtd5 | 00040000 | 00040000  | "zloader"     |
| mtd6 | 04000000 | 00040000  | "ubi"         |
| mtd7 | 04000000 | 00040000  | "ubi2"        |
| mtd8 | 15a80000 | 00040000  | "zyubi"       |

The router boots BL2 which than loads FIP (u-boot).
U-boot has hardcoded a command to always launch Zloader "mtd read zloader 0x46000000" and than "bootm". Bootargs are deactivated.
Zloader is the zyxel booloader which allow to dual-boot ubi or ubi2, by default access to zloader is blocked.
Too zloader checks that the firmware contains a particolar file called zyfwinfo.
Additional details regarding Zloader can be found here:
https://hack-gpon.github.io/zyxel/
https://forum.openwrt.org/t/adding-openwrt-support-for-zyxel-ex5601-t0/155914

Hardware
--------
SOC: MediaTek MT7986a
CPU: 4 core cortex-a53 (2000MHz)
RAM: 1GB DDR4
FLASH: 512MB SPI-NAND (Micron xxx)
WIFI: Wifi6 Mediatek MT7976 802.11ax 5 GHz 4x4 + 2.4GHZ 4x4
ETH: MediaTek MT7531 Switch + SoC
3 x builtin 1G phy (lan1, lan2, lan3)
1 x MaxLinear GPY211B 2.5 N-Base-T phy5 (lan4)
1 x MaxLinear GPY211B 2.5Gbit xor SFP/N-Base-T phy6 (wan)
USB: 1 x USB 3.2 Enhanced SuperSpeed port
UART: 3V3 115200 8N1 (Pinout: GND KEY RX TX VCC)
VOIP: 2 FXS ports for analog phones

MAC Address Table
-----------------
eth0/lan    Factory 0x002a
eth1/wan    Factory 0x0024
wifi 2.4Ghz Factory 0x0004
wifi 5Ghz   Factory 0x0004 + 1

Serial console (UART)
---------------------
+-------+-------+-------+-------+-------+
| +3.3V |  RX   |  TX   |  KEY  |  GND  |
+---+---+-------+-------+-------+-------+
    |
    +--- Don't connect

Installation
------------
Keep in mind that openwrt can only run on the UBI partition, the openwrt firmware is not able to understand the zloader bootargs.
The procedure allows restoring the UBI partition with the Zyxel firmware and retains all the OEM functionalities.

1. Unlock Zloader (this will allow to swap manually between partitions UBI and UBI2):
- Attach a usb-ttl adapter to your computer and boot the router.
- While the router is booting at some point you will read the following: `Please press Enter to activate this console.`
- As soon as you read that press enter, type root and than press enter again (just do it, don't care about the logs scrolling).
- Most likely the router is still printing the boot log, leave it boot until it stops.
- If everything went ok you should have full root access "root@EX5601-T0:/#".
- Type the following command and press enter: "fw_setenv EngDebugFlag 0x1".
- Reboot the router.
- As soon as you read `Hit any key to stop autoboot:` press Enter.
- If everything went ok you should have the following prompt: "ZHAL>".
- You have successfully unlocked zloader access, this procedure must be done only once.

2. Check the current active partition:
- Boot the router and repeat the steps above to gain root access.
- Type the following command to check the current active image: "cat /proc/cmdline".
- If `rootubi=ubi` it means that the active partition is `mtd6`
- If `rootubi=ubi2` it means that the active partition is `mtd7`
- As mentioned earlier we need to flash openwrt into ubi/mtd6 and never overwrite ubi2/mtd7 to be able to fully roll-back.
- To activate and boot from mtd7 (ubi2) enter into ZHAL> command prompt and type the following commands:
atbt 1  # unlock write
atsw    # swap boot partition
atsr    # reboot the router
- After rebooting check again with "cat /proc/cmdline" that you are correctly booting from mtd7/ubi2
- If yes proceed with the installation guide. If not probably you don't have a firmware into ubi2 or you did something wrong.

3. Flashing:
- Download the sysupgrade file for the router from openwrt, than we need to add the zyfwinfo file into the sysupgrade tar.
Zloader only checks for the magic (which is a fixed value 'EXYZ') and the crc of the file itself (256bytes).
I created a script to create a valid zyfwinfo file but you can use anything that does exactly the same:
https://raw.githubusercontent.com/pameruoso/OpenWRT-Zyxel-EX5601-T0/main/gen_zyfwinfo.sh
- Add the zyfwinfo file into the sysupgrade tar.
- Enter via telnet or ssh into the router with admin credentials
- Enter the following commands to disable the firmware and model checks
"zycli fwidcheck off" and "zycli modelcheck off"
- Open the router web interface and in the update firmware page select the "restore default settings option"
- Select the sysupgrade file and click on upload.
- The router will flash and reboot itself into openwrt from UBI

4. Restoring and going back to Zyxel firmware.
- Use the ZHAL> command line to manually swap the boot parition to UBI2 with the following:
atbt 1  # unlock write
atsw    # swap boot partition
atsr    # reboot the router
- You will boot again the Zyxel firmware you have into UBI2 and you can flash the zyxel firmware to overwrite the UBI partition and openwrt.

Working features
----------------
3 gbit lan ports
Wifi
Zyxel partitioning for coexistance with Zloader and dual boot.
WAN SFP port (only after exporting pins 57 and 10. gpiobase411)
leds
reset button
serial interface
usb port
lan ethernet 2.5 gbit port (autosense)
wan ethernet 2.5 gbit port (autosense)

Not working
----------------
voip (missing drivers or proper zyxel platform software)

Swapping the wan ethernet/sfp xor port
----------------
The way to swap the wan port between sfp and ethernet is the following:
export the pins 57 and 10.
Pin 57 is used to probe if an sfp is present.
If pin 57 value is 0 it means that an sfp is present into the cage (cat /sys/class/gpio/gpio468/value).
If pin 57 value is 1 it means that no sfp is inserted into the cage.
In conclusion by default both 57 an 10 pins are by default 1, which means that the active port is the ethernet one.
After inserting an SFP pin 57 will become 0 and you have to manually change the value of pin 10 to 0 too.
This is totally scriptable of course.

Leds description
------------
All the leds are working out of the box but the leds managed by the 2 maxlinear phy (phy 5 lan, phy6 wan).
To activate the phy5 led (rj45 ethernet port led on the back of the router) you have to use mdio-tools.
To activate the phy6 led (led on the front of the router for 2.5gbit link) you have to use mdio-tools.
Example:
Set lan5 led to fast blink on 2500/1000, slow blink on 10/100:
mdio mdio-bus mmd 5:30 raw 0x0001 0x33FC

Set wan 2.5gbit led to constant on when wan is 2.5gbit:
mdio mdio-bus mmd 6:30 raw 0x0001 0x0080

Signed-off-by: Pietro Ameruoso <p.ameruoso@live.it>
(cherry picked from commit 1c05388ab0)
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2023-05-24 19:26:11 +01:00

320 lines
12 KiB
Makefile
Raw Blame History

DTS_DIR := $(DTS_DIR)/mediatek
define Image/Prepare
# For UBI we want only one extra block
rm -f $(KDIR)/ubi_mark
echo -ne '\xde\xad\xc0\xde' > $(KDIR)/ubi_mark
endef
define Build/bl2
cat $(STAGING_DIR_IMAGE)/mt7986-$1-bl2.img >> $@
endef
define Build/bl31-uboot
cat $(STAGING_DIR_IMAGE)/mt7986_$1-u-boot.fip >> $@
endef
define Build/mt7986-gpt
cp $@ $@.tmp 2>/dev/null || true
ptgen -g -o $@.tmp -a 1 -l 1024 \
$(if $(findstring sdmmc,$1), \
-H \
-t 0x83 -N bl2 -r -p 4079k@17k \
) \
-t 0x83 -N ubootenv -r -p 512k@4M \
-t 0x83 -N factory -r -p 2M@4608k \
-t 0xef -N fip -r -p 4M@6656k \
-N recovery -r -p 32M@12M \
$(if $(findstring sdmmc,$1), \
-N install -r -p 20M@44M \
-t 0x2e -N production -p $(CONFIG_TARGET_ROOTFS_PARTSIZE)M@64M \
) \
$(if $(findstring emmc,$1), \
-t 0x2e -N production -p $(CONFIG_TARGET_ROOTFS_PARTSIZE)M@64M \
)
cat $@.tmp >> $@
rm $@.tmp
endef
metadata_gl_json = \
'{ $(if $(IMAGE_METADATA),$(IMAGE_METADATA)$(comma)) \
"metadata_version": "1.1", \
"compat_version": "$(call json_quote,$(compat_version))", \
$(if $(DEVICE_COMPAT_MESSAGE),"compat_message": "$(call json_quote,$(DEVICE_COMPAT_MESSAGE))"$(comma)) \
$(if $(filter-out 1.0,$(compat_version)),"new_supported_devices": \
[$(call metadata_devices,$(SUPPORTED_DEVICES))]$(comma) \
"supported_devices": ["$(call json_quote,$(legacy_supported_message))"]$(comma)) \
$(if $(filter 1.0,$(compat_version)),"supported_devices":[$(call metadata_devices,$(SUPPORTED_DEVICES))]$(comma)) \
"version": { \
"release": "$(call json_quote,$(VERSION_NUMBER))", \
"date": "$(shell TZ='Asia/Chongqing' date '+%Y%m%d%H%M%S')", \
"dist": "$(call json_quote,$(VERSION_DIST))", \
"version": "$(call json_quote,$(VERSION_NUMBER))", \
"revision": "$(call json_quote,$(REVISION))", \
"target": "$(call json_quote,$(TARGETID))", \
"board": "$(call json_quote,$(if $(BOARD_NAME),$(BOARD_NAME),$(DEVICE_NAME)))" \
} \
}'
define Build/append-gl-metadata
$(if $(SUPPORTED_DEVICES),-echo $(call metadata_gl_json,$(SUPPORTED_DEVICES)) | fwtool -I - $@)
sha256sum "$@" | cut -d" " -f1 > "$@.sha256sum"
[ ! -s "$(BUILD_KEY)" -o ! -s "$(BUILD_KEY).ucert" -o ! -s "$@" ] || { \
cp "$(BUILD_KEY).ucert" "$@.ucert" ;\
usign -S -m "$@" -s "$(BUILD_KEY)" -x "$@.sig" ;\
ucert -A -c "$@.ucert" -x "$@.sig" ;\
fwtool -S "$@.ucert" "$@" ;\
}
endef
define Device/asus_tuf-ax4200
DEVICE_VENDOR := ASUS
DEVICE_MODEL := TUF-AX4200
DEVICE_DTS := mt7986a-asus-tuf-ax4200
DEVICE_DTS_DIR := ../dts
DEVICE_DTS_LOADADDR := 0x47000000
DEVICE_PACKAGES := kmod-usb3 kmod-mt7986-firmware mt7986-wo-firmware
IMAGES := sysupgrade.bin
KERNEL := kernel-bin | lzma | \
fit lzma $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb
KERNEL_INITRAMFS := kernel-bin | lzma | \
fit lzma $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb with-initrd | pad-to 64k
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
endef
TARGET_DEVICES += asus_tuf-ax4200
define Device/bananapi_bpi-r3
DEVICE_VENDOR := Bananapi
DEVICE_MODEL := BPi-R3
DEVICE_DTS := mt7986a-bananapi-bpi-r3
DEVICE_DTS_CONFIG := config-mt7986a-bananapi-bpi-r3
DEVICE_DTS_OVERLAY:= mt7986a-bananapi-bpi-r3-nor mt7986a-bananapi-bpi-r3-emmc-nor mt7986a-bananapi-bpi-r3-emmc-snand mt7986a-bananapi-bpi-r3-snand
DEVICE_DTS_DIR := ../dts
DEVICE_PACKAGES := kmod-hwmon-pwmfan kmod-i2c-gpio kmod-mt7986-firmware kmod-sfp kmod-usb3 e2fsprogs f2fsck mkf2fs mt7986-wo-firmware
IMAGES := sysupgrade.itb
KERNEL_LOADADDR := 0x44000000
KERNEL_INITRAMFS_SUFFIX := -recovery.itb
ARTIFACTS := \
emmc-preloader.bin emmc-bl31-uboot.fip \
nor-preloader.bin nor-bl31-uboot.fip \
sdcard.img.gz \
snand-preloader.bin snand-bl31-uboot.fip
ARTIFACT/emmc-preloader.bin := bl2 emmc-ddr4
ARTIFACT/emmc-bl31-uboot.fip := bl31-uboot bananapi_bpi-r3-emmc
ARTIFACT/nor-preloader.bin := bl2 nor-ddr4
ARTIFACT/nor-bl31-uboot.fip := bl31-uboot bananapi_bpi-r3-nor
ARTIFACT/snand-preloader.bin := bl2 spim-nand-ddr4
ARTIFACT/snand-bl31-uboot.fip := bl31-uboot bananapi_bpi-r3-snand
ARTIFACT/sdcard.img.gz := mt7986-gpt sdmmc |\
pad-to 17k | bl2 sdmmc-ddr4 |\
pad-to 6656k | bl31-uboot bananapi_bpi-r3-sdmmc |\
$(if $(CONFIG_TARGET_ROOTFS_INITRAMFS),\
pad-to 12M | append-image-stage initramfs-recovery.itb | check-size 44m |\
) \
pad-to 44M | bl2 spim-nand-ddr4 |\
pad-to 45M | bl31-uboot bananapi_bpi-r3-snand |\
pad-to 49M | bl2 nor-ddr4 |\
pad-to 50M | bl31-uboot bananapi_bpi-r3-nor |\
pad-to 51M | bl2 emmc-ddr4 |\
pad-to 52M | bl31-uboot bananapi_bpi-r3-emmc |\
pad-to 56M | mt7986-gpt emmc |\
$(if $(CONFIG_TARGET_ROOTFS_SQUASHFS),\
pad-to 64M | append-image squashfs-sysupgrade.itb | check-size | gzip \
)
IMAGE_SIZE := $$(shell expr 64 + $$(CONFIG_TARGET_ROOTFS_PARTSIZE))m
KERNEL := kernel-bin | gzip
KERNEL_INITRAMFS := kernel-bin | lzma | \
fit lzma $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb with-initrd | pad-to 64k
IMAGE/sysupgrade.itb := append-kernel | fit gzip $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb external-static-with-rootfs | pad-rootfs | append-metadata
DTC_FLAGS += -@ --space 32768
endef
TARGET_DEVICES += bananapi_bpi-r3
define Device/cudy_wr3000-v1
DEVICE_VENDOR := Cudy
DEVICE_MODEL := WR3000
DEVICE_VARIANT := v1
DEVICE_DTS := mt7981b-cudy-wr3000-v1
DEVICE_DTS_DIR := ../dts
DEVICE_DTS_LOADADDR := 0x47000000
IMAGES := sysupgrade.bin
IMAGE_SIZE := 15424k
SUPPORTED_DEVICES += R31
KERNEL := kernel-bin | lzma | \
fit lzma $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb
KERNEL_INITRAMFS := kernel-bin | lzma | \
fit lzma $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb with-initrd | pad-to 64k
IMAGE/sysupgrade.bin := append-kernel | pad-to 128k | append-rootfs | pad-rootfs | check-size | append-metadata
DEVICE_PACKAGES := kmod-mt7981-firmware
endef
TARGET_DEVICES += cudy_wr3000-v1
define Device/glinet_gl-mt3000
DEVICE_VENDOR := GL.iNet
DEVICE_MODEL := GL-MT3000
DEVICE_DTS := mt7981b-glinet-gl-mt3000
DEVICE_DTS_DIR := ../dts
SUPPORTED_DEVICES += glinet,mt3000-snand
DEVICE_PACKAGES := kmod-mt7981-firmware mt7981-wo-firmware kmod-hwmon-pwmfan kmod-usb3
UBINIZE_OPTS := -E 5
BLOCKSIZE := 128k
PAGESIZE := 2048
IMAGE_SIZE := 246272k
KERNEL_IN_UBI := 1
IMAGE/sysupgrade.bin := sysupgrade-tar | append-gl-metadata
endef
TARGET_DEVICES += glinet_gl-mt3000
define Device/mediatek_mt7986a-rfb-nand
DEVICE_VENDOR := MediaTek
DEVICE_MODEL := MT7986 rfba AP (NAND)
DEVICE_DTS := mt7986a-rfb-spim-nand
DEVICE_DTS_DIR := $(DTS_DIR)/
DEVICE_PACKAGES := kmod-mt7986-firmware mt7986-wo-firmware
SUPPORTED_DEVICES := mediatek,mt7986a-rfb-snand
UBINIZE_OPTS := -E 5
BLOCKSIZE := 128k
PAGESIZE := 2048
IMAGE_SIZE := 65536k
KERNEL_IN_UBI := 1
IMAGES += factory.bin
IMAGE/factory.bin := append-ubi | check-size $$$$(IMAGE_SIZE)
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
KERNEL = kernel-bin | lzma | \
fit lzma $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb
KERNEL_INITRAMFS = kernel-bin | lzma | \
fit lzma $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb with-initrd
DTC_FLAGS += -@ --space 32768
endef
TARGET_DEVICES += mediatek_mt7986a-rfb-nand
define Device/mediatek_mt7986b-rfb
DEVICE_VENDOR := MediaTek
DEVICE_MODEL := MTK7986 rfbb AP
DEVICE_DTS := mt7986b-rfb
DEVICE_DTS_DIR := $(DTS_DIR)/
DEVICE_PACKAGES := kmod-mt7986-firmware mt7986-wo-firmware
SUPPORTED_DEVICES := mediatek,mt7986b-rfb
UBINIZE_OPTS := -E 5
BLOCKSIZE := 128k
PAGESIZE := 2048
IMAGE_SIZE := 65536k
KERNEL_IN_UBI := 1
IMAGES += factory.bin
IMAGE/factory.bin := append-ubi | check-size $$$$(IMAGE_SIZE)
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
endef
TARGET_DEVICES += mediatek_mt7986b-rfb
define Device/tplink_tl-xdr-common
DEVICE_VENDOR := TP-Link
DEVICE_DTS_DIR := ../dts
UBINIZE_OPTS := -E 5
BLOCKSIZE := 128k
PAGESIZE := 2048
KERNEL_IN_UBI := 1
UBOOTENV_IN_UBI := 1
IMAGES := sysupgrade.itb
KERNEL_INITRAMFS_SUFFIX := -recovery.itb
KERNEL := kernel-bin | gzip
KERNEL_INITRAMFS := kernel-bin | lzma | \
fit lzma $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb with-initrd | pad-to 64k
IMAGE/sysupgrade.itb := append-kernel | \
fit gzip $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb external-static-with-rootfs | append-metadata
DEVICE_PACKAGES := kmod-usb3 kmod-mt7986-firmware mt7986-wo-firmware
ARTIFACTS := preloader.bin bl31-uboot.fip
ARTIFACT/preloader.bin := bl2 spim-nand-ddr3
endef
define Device/tplink_tl-xdr4288
DEVICE_MODEL := TL-XDR4288
DEVICE_DTS := mt7986a-tplink-tl-xdr4288
ARTIFACT/bl31-uboot.fip := bl31-uboot tplink_tl-xdr4288
$(call Device/tplink_tl-xdr-common)
endef
TARGET_DEVICES += tplink_tl-xdr4288
define Device/tplink_tl-xdr6086
DEVICE_MODEL := TL-XDR6086
DEVICE_DTS := mt7986a-tplink-tl-xdr6086
ARTIFACT/bl31-uboot.fip := bl31-uboot tplink_tl-xdr6086
$(call Device/tplink_tl-xdr-common)
endef
TARGET_DEVICES += tplink_tl-xdr6086
define Device/tplink_tl-xdr6088
DEVICE_MODEL := TL-XDR6088
DEVICE_DTS := mt7986a-tplink-tl-xdr6088
ARTIFACT/bl31-uboot.fip := bl31-uboot tplink_tl-xdr6088
$(call Device/tplink_tl-xdr-common)
endef
TARGET_DEVICES += tplink_tl-xdr6088
define Device/xiaomi_redmi-router-ax6000-stock
DEVICE_VENDOR := Xiaomi
DEVICE_MODEL := Redmi Router AX6000 (stock layout)
DEVICE_DTS := mt7986a-xiaomi-redmi-router-ax6000-stock
DEVICE_DTS_DIR := ../dts
DEVICE_PACKAGES := kmod-leds-ws2812b kmod-mt7986-firmware mt7986-wo-firmware
UBINIZE_OPTS := -E 5
BLOCKSIZE := 128k
PAGESIZE := 2048
ifneq ($(CONFIG_TARGET_ROOTFS_INITRAMFS),)
ARTIFACTS := initramfs-factory.ubi
ARTIFACT/initramfs-factory.ubi := append-image-stage initramfs-kernel.bin | ubinize-kernel
endif
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
endef
TARGET_DEVICES += xiaomi_redmi-router-ax6000-stock
define Device/xiaomi_redmi-router-ax6000-ubootmod
DEVICE_VENDOR := Xiaomi
DEVICE_MODEL := Redmi Router AX6000 (OpenWrt U-Boot layout)
DEVICE_DTS := mt7986a-xiaomi-redmi-router-ax6000-ubootmod
DEVICE_DTS_DIR := ../dts
DEVICE_PACKAGES := kmod-leds-ws2812b kmod-mt7986-firmware mt7986-wo-firmware
KERNEL_INITRAMFS_SUFFIX := -recovery.itb
IMAGES := sysupgrade.itb
UBINIZE_OPTS := -E 5
BLOCKSIZE := 128k
PAGESIZE := 2048
KERNEL_IN_UBI := 1
UBOOTENV_IN_UBI := 1
KERNEL := kernel-bin | gzip
KERNEL_INITRAMFS := kernel-bin | lzma | \
fit lzma $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb with-initrd | pad-to 64k
IMAGE/sysupgrade.itb := append-kernel | \
fit gzip $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb external-static-with-rootfs | append-metadata
ARTIFACTS := preloader.bin bl31-uboot.fip
ARTIFACT/preloader.bin := bl2 spim-nand-ddr4
ARTIFACT/bl31-uboot.fip := bl31-uboot xiaomi_redmi-router-ax6000
ifneq ($(CONFIG_TARGET_ROOTFS_INITRAMFS),)
ARTIFACTS += initramfs-factory.ubi
ARTIFACT/initramfs-factory.ubi := append-image-stage initramfs-recovery.itb | ubinize-kernel
endif
endef
TARGET_DEVICES += xiaomi_redmi-router-ax6000-ubootmod
define Device/zyxel_ex5601-t0-stock
DEVICE_VENDOR := Zyxel
DEVICE_MODEL := EX5601-T0 (stock layout)
DEVICE_DTS := mt7986a-zyxel-ex5601-t0-stock
DEVICE_DTS_DIR := ../dts
DEVICE_PACKAGES := kmod-mt7986-firmware mt7986-wo-firmware
SUPPORTED_DEVICES := mediatek,mt7986a-rfb-snand
UBINIZE_OPTS := -E 5
BLOCKSIZE := 256k
PAGESIZE := 4096
IMAGE_SIZE := 65536k
KERNEL_IN_UBI := 1
IMAGES += factory.bin
IMAGE/factory.bin := append-ubi | check-size $$$$(IMAGE_SIZE)
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
KERNEL = kernel-bin | lzma | \
fit lzma $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb
KERNEL_INITRAMFS = kernel-bin | lzma | \
fit lzma $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb with-initrd
DTC_FLAGS += -@ --space 32768
endef
TARGET_DEVICES += zyxel_ex5601-t0-stock
Reference in New Issue View Git Blame Copy Permalink