openwrt/target/linux/ath79/dts/qca9533_comfast_cf-e110n-v2.dts
Adrian Schmutzler 8961d2268e ath79: convert devices to interrupt-driven gpio-keys
This converts all remaining devices to use interrupt-driven
gpio-keys compatible instead of gpio-keys-polled.
The poll-interval is removed.

Only ar7240_netgear_wnr612-v2 is kept at gpio-keys-polled, as
this one is using ath9k keys.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Tested-by: Karl Palsson <karlp@etactica.com>
Tested-by: Dmitry Tunin <hanipouspilot@gmail.com>
2019-09-22 18:28:11 +02:00

158 lines
2.7 KiB
Plaintext

// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
/dts-v1/;
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>
#include "qca953x.dtsi"
/ {
compatible = "comfast,cf-e110n-v2", "qca,qca9533";
model = "COMFAST CF-E110N v2";
aliases {
serial0 = &uart;
led-boot = &wan;
led-failsafe = &wan;
led-upgrade = &wan;
};
leds {
compatible = "gpio-leds";
pinctrl-names = "default";
pinctrl-0 = <&jtag_disable_pins &led_rssilow_pin &led_rssimediumhigh_pin &led_rssihigh_pin>;
wan: wan {
label = "cf-e110n-v2:green:wan";
gpios = <&gpio 3 GPIO_ACTIVE_LOW>;
};
lan {
label = "cf-e110n-v2:green:lan";
gpios = <&gpio 2 GPIO_ACTIVE_LOW>;
};
rssilow {
label = "cf-e110n-v2:red:rssilow";
gpios = <&gpio 11 GPIO_ACTIVE_LOW>;
};
rssimediumlow {
label = "cf-e110n-v2:red:rssimediumlow";
gpios = <&gpio 12 GPIO_ACTIVE_LOW>;
};
rssimediumhigh {
label = "cf-e110n-v2:green:rssimediumhigh";
gpios = <&gpio 14 GPIO_ACTIVE_LOW>;
};
rssihigh {
label = "cf-e110n-v2:green:rssihigh";
gpios = <&gpio 16 GPIO_ACTIVE_LOW>;
};
};
ath9k-leds {
compatible = "gpio-leds";
wlan {
label = "cf-e110n-v2:green:wlan";
gpios = <&gpio 0 GPIO_ACTIVE_LOW>;
linux,default-trigger = "phy0tpt";
};
};
keys {
compatible = "gpio-keys";
reset {
label = "reset";
linux,code = <KEY_RESTART>;
gpios = <&gpio 17 GPIO_ACTIVE_LOW>;
debounce-interval = <60>;
};
};
};
&pinmux {
led_rssilow_pin: pinmux_rssilow_pin {
pinctrl-single,bits = <0x8 0x0 0xff000000>;
};
led_rssimediumhigh_pin: pinmux_rssimediumhigh_pin {
pinctrl-single,bits = <0xc 0x0 0x00ff0000>;
};
led_rssihigh_pin: pinmux_rssihigh_pin {
pinctrl-single,bits = <0x10 0x0 0x000000ff>;
};
};
&spi {
status = "okay";
num-cs = <1>;
flash@0 {
compatible = "winbond,w25q128", "jedec,spi-nor";
reg = <0>;
spi-max-frequency = <25000000>;
partitions {
compatible = "fixed-partitions";
#address-cells = <1>;
#size-cells = <1>;
partition@0 {
label = "u-boot";
reg = <0x000000 0x010000>;
read-only;
};
art: partition@10000 {
label = "art";
reg = <0x010000 0x010000>;
read-only;
};
partition@20000 {
compatible = "denx,uimage";
label = "firmware";
reg = <0x020000 0xfd0000>;
};
partition@ff0000 {
label = "nvram";
reg = <0xff0000 0x010000>;
read-only;
};
};
};
};
&uart {
status = "okay";
};
&eth0 {
status = "okay";
mtd-mac-address = <&art 0x0>;
phy-handle = <&swphy4>;
};
&eth1 {
status = "okay";
mtd-mac-address = <&art 0x1002>;
gmac-config {
device = <&gmac>;
};
};
&wmac {
status = "okay";
mtd-cal-data = <&art 0x1000>;
mtd-mac-address = <&art 0x6>;
};