mirror of
https://github.com/openwrt/openwrt.git
synced 2024-12-22 23:12:32 +00:00
3a4b751110
The uart node is enabled on all devices except one (GL-USB150 *). Thus, let's not have a few hundred nodes to enable it, but do not disable it in the first place. Where the majority of devices is using it, also move the serial0 alias to the DTSI. *) Since GL-USB150 even defines serial0 alias, the missing uart is probably just a mistake. Anyway, disable it for now so this patch stays cosmetic. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
173 lines
2.7 KiB
Plaintext
173 lines
2.7 KiB
Plaintext
// SPDX-License-Identifier: GPL-1.0-or-later OR MIT
|
|
|
|
#include "ar7100.dtsi"
|
|
|
|
#include <dt-bindings/gpio/gpio.h>
|
|
#include <dt-bindings/input/input.h>
|
|
|
|
/ {
|
|
aliases {
|
|
led-boot = &led_user;
|
|
led-failsafe = &led_user;
|
|
led-running = &led_user;
|
|
};
|
|
|
|
leds {
|
|
compatible = "gpio-leds";
|
|
|
|
led_user: user {
|
|
label = "yellow:user";
|
|
gpios = <&gpio 4 GPIO_ACTIVE_HIGH>;
|
|
default-state = "on";
|
|
};
|
|
|
|
led1 {
|
|
label = "green:led1";
|
|
gpios = <&cpld_gpio 0 GPIO_ACTIVE_LOW>;
|
|
};
|
|
|
|
led2 {
|
|
label = "green:led2";
|
|
gpios = <&cpld_gpio 2 GPIO_ACTIVE_LOW>;
|
|
};
|
|
|
|
led3 {
|
|
label = "green:led3";
|
|
gpios = <&cpld_gpio 1 GPIO_ACTIVE_LOW>;
|
|
};
|
|
|
|
led4 {
|
|
label = "green:led4";
|
|
gpios = <&cpld_gpio 3 GPIO_ACTIVE_LOW>;
|
|
};
|
|
|
|
led5 {
|
|
label = "green:led5";
|
|
gpios = <&cpld_gpio 8 GPIO_ACTIVE_LOW>;
|
|
};
|
|
};
|
|
};
|
|
|
|
&gpio {
|
|
ngpios = <31>;
|
|
gpio-line-names =
|
|
"", "", "", "", "LED", "RDY", "", "MDC",
|
|
"MDIO", "", "", "", "", "", "", "",
|
|
"", "", "", "", "", "", "", "",
|
|
"", "", "", "", "", "", "", "";
|
|
};
|
|
|
|
&pcie0 {
|
|
status = "okay";
|
|
};
|
|
|
|
&spi {
|
|
status = "okay";
|
|
|
|
compatible = "mikrotik,rb4xx-spi";
|
|
|
|
flash@0 {
|
|
compatible = "pm25lv512", "jedec,spi-nor";
|
|
|
|
reg = <0>;
|
|
spi-max-frequency = <25000000>;
|
|
|
|
partitions {
|
|
compatible = "mikrotik,routerboot-partitions";
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
|
|
partition@0 {
|
|
label = "routerboot1";
|
|
reg = <0x0 0x0>;
|
|
read-only;
|
|
};
|
|
|
|
hard_config {
|
|
label = "hard_config";
|
|
read-only;
|
|
};
|
|
|
|
bios {
|
|
label = "bios";
|
|
size = <0x1000>;
|
|
read-only;
|
|
};
|
|
|
|
routerboot2 {
|
|
label = "routerboot2";
|
|
read-only;
|
|
};
|
|
|
|
soft_config {
|
|
label = "soft_config";
|
|
};
|
|
};
|
|
};
|
|
|
|
cpld@1 {
|
|
compatible = "mikrotik,rb4xx-cpld";
|
|
|
|
reg = <1>;
|
|
spi-max-frequency = <25000000>;
|
|
|
|
cpld_gpio: gpio {
|
|
compatible = "mikrotik,rb4xx-gpio";
|
|
|
|
base = <32>;
|
|
|
|
gpio-controller;
|
|
#gpio-cells = <2>;
|
|
gpio-line-names =
|
|
"LED1", "LED2", "LED3", "LED4",
|
|
"FAN", "ALE", "CLE", "nCE",
|
|
"LED5";
|
|
};
|
|
|
|
nand {
|
|
compatible = "mikrotik,rb4xx-nand";
|
|
|
|
gpios = <&cpld_gpio 5 GPIO_ACTIVE_HIGH>, // ALE
|
|
<&cpld_gpio 6 GPIO_ACTIVE_HIGH>, // CLE
|
|
<&cpld_gpio 7 GPIO_ACTIVE_HIGH>, // nCE
|
|
<&gpio 5 GPIO_ACTIVE_HIGH>; // RDY
|
|
|
|
partitions {
|
|
compatible = "fixed-partitions";
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
|
|
partition@0 {
|
|
label = "booter";
|
|
reg = <0x0000000 0x0040000>;
|
|
read-only;
|
|
};
|
|
|
|
partition@40000 {
|
|
label = "kernel";
|
|
reg = <0x0040000 0x0800000>;
|
|
};
|
|
|
|
partition@840000 {
|
|
label = "ubi";
|
|
reg = <0x0840000 0x77c0000>;
|
|
};
|
|
};
|
|
};
|
|
};
|
|
};
|
|
|
|
ð0 {
|
|
status = "okay";
|
|
|
|
phy-handle = <&phy0>;
|
|
};
|
|
|
|
&mdio0 {
|
|
status = "okay";
|
|
|
|
phy0: ethernet-phy@0 {
|
|
reg = <0>;
|
|
};
|
|
};
|