mirror of
https://github.com/openwrt/openwrt.git
synced 2024-12-22 15:02:32 +00:00
e1223dbee3
The MikroTik mAP-2nd (sold as mAP) is an indoor 2.4Ghz AP with 802.3af/at PoE input and passive PoE passthrough. See https://mikrotik.com/product/RBmAP2nD for more details. Specifications: - SoC: QCA9533 - RAM: 64MB - Storage: 16MB NOR - Wireless: QCA9533 802.11b/g/n 2x2 - Ethernet: 2x 10/100 ports, 802.3af/at PoE in port 1, 500 mA passive PoE out on port 2 - 7 user-controllable LEDs Note: the device is a tiny AP and does not distinguish between both ethernet ports roles, so they are both assigned to lan. With the current setup, ETH1 is connected to eth1 and ETH2 is connected to eth0 via the embedded switch port 2. Flashing: TFTP boot initramfs image and then perform sysupgrade. The "ETH1" port must be used to upload the TFTP image. Follow common MikroTik procedure as in https://openwrt.org/toh/mikrotik/common. Tested-By: Andrew Powers-Holmes <aholmes@omnom.net> Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
114 lines
1.8 KiB
Plaintext
114 lines
1.8 KiB
Plaintext
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
|
|
|
#include "qca9533_mikrotik_routerboard-16m.dtsi"
|
|
|
|
/ {
|
|
compatible = "mikrotik,routerboard-map-2nd", "qca,qca9533";
|
|
model = "MikroTik RouterBOARD mAP-2nD (mAP)";
|
|
|
|
aliases {
|
|
led-boot = &led_user;
|
|
led-failsafe = &led_user;
|
|
led-running = &led_user;
|
|
led-upgrade = &led_user;
|
|
};
|
|
|
|
leds {
|
|
compatible = "gpio-leds";
|
|
|
|
power {
|
|
label = "green:power";
|
|
gpios = <&gpio 4 GPIO_ACTIVE_LOW>;
|
|
default-state = "on";
|
|
};
|
|
|
|
eth_1 {
|
|
label = "green:eth_1";
|
|
gpios = <&gpio_ext 0 GPIO_ACTIVE_LOW>;
|
|
};
|
|
|
|
eth_2 {
|
|
label = "green:eth_2";
|
|
gpios = <&gpio_ext 1 GPIO_ACTIVE_LOW>;
|
|
};
|
|
|
|
poe_out {
|
|
label = "red:poe_out";
|
|
gpios = <&gpio_ext 2 GPIO_ACTIVE_LOW>;
|
|
};
|
|
|
|
led_user: user {
|
|
label = "green:user";
|
|
gpios = <&gpio_ext 3 GPIO_ACTIVE_LOW>;
|
|
};
|
|
|
|
wlan {
|
|
label = "green:wlan";
|
|
gpios = <&gpio_ext 4 GPIO_ACTIVE_LOW>;
|
|
linux,default-trigger = "phy0tpt";
|
|
};
|
|
|
|
ap_cap {
|
|
label = "green:ap_cap";
|
|
gpios = <&gpio_ext 6 GPIO_ACTIVE_LOW>;
|
|
};
|
|
|
|
};
|
|
|
|
gpio-export {
|
|
compatible = "gpio-export";
|
|
|
|
usb_power {
|
|
gpio-export,name = "usb-power";
|
|
gpio-export,output = <1>;
|
|
gpios = <&gpio_ext 5 GPIO_ACTIVE_LOW>;
|
|
};
|
|
|
|
enable_poe_port5 {
|
|
gpio-export,name = "enable-poe";
|
|
gpio-export,output = <0>;
|
|
gpios = <&gpio 14 GPIO_ACTIVE_HIGH>;
|
|
};
|
|
};
|
|
};
|
|
|
|
&spi {
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&pin_spi_cs1>;
|
|
|
|
gpio_ext: gpio_ext@1 {
|
|
compatible = "fairchild,74hc595";
|
|
reg = <1>;
|
|
gpio-controller;
|
|
#gpio-cells = <2>;
|
|
registers-number = <1>;
|
|
spi-max-frequency = <25000000>;
|
|
};
|
|
};
|
|
|
|
|
|
&pinmux {
|
|
pin_spi_cs1: pinmux_spi_cs1 {
|
|
pinctrl-single,bits = <0x8 0x0a000000 0xff000000>;
|
|
};
|
|
};
|
|
|
|
ð0 {
|
|
status = "okay";
|
|
|
|
phy-handle = <&swphy0>;
|
|
|
|
gmac-config {
|
|
device = <&gmac>;
|
|
switch-phy-swap = <1>;
|
|
};
|
|
};
|
|
|
|
&usb0 {
|
|
status = "okay";
|
|
};
|
|
|
|
&usb_phy {
|
|
status = "okay";
|
|
};
|