mirror of
https://github.com/openwrt/openwrt.git
synced 2024-12-22 15:02:32 +00:00
5c147d36ba
The device was added for ar71xx target and dropped during the ath79 transition, mainly because of the ascii mac address stored in bdinfo partition Device page, http://wiki.openwrt.org/toh/hiwifi/hc6361 The vendor u-boot image accepts sysupgrade.bin image with specific requirements, including having squashfs signature "hsqs" at file offset 0x140000. This is not possible now that OpenWrt kernel image is at least 2MB with the signature at offset 0x240000. Installation of current build of OpenWrt now requires a bootstrap step of installing an earlier version first. - If the vendor u-boot accepts sysupgrade image, hc6361 image of LEDE release should work - If the vendor u-boot accepts only verified flashsmt image, install the one in the above device page. The image is based on Barrier Breaker SHA256SUM of the flashsmt image 81b193b95ea5f8e5c30cd62fa9facf275f39233be4fdeed7038f3deed2736156 After the bootstrap step, current build of OpenWrt can be installed there fine. Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
157 lines
2.5 KiB
Plaintext
157 lines
2.5 KiB
Plaintext
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
|
|
|
#include "ar9331.dtsi"
|
|
|
|
#include <dt-bindings/gpio/gpio.h>
|
|
#include <dt-bindings/input/input.h>
|
|
|
|
/ {
|
|
model = "HiWiFi HC6361";
|
|
compatible = "hiwifi,hc6361", "qca,ar9331";
|
|
|
|
aliases {
|
|
serial0 = &uart;
|
|
led-boot = &led_system;
|
|
led-failsafe = &led_system;
|
|
led-running = &led_system;
|
|
led-upgrade = &led_system;
|
|
};
|
|
|
|
keys {
|
|
compatible = "gpio-keys";
|
|
|
|
reset {
|
|
label = "reset";
|
|
linux,code = <KEY_RESTART>;
|
|
gpios = <&gpio 11 GPIO_ACTIVE_LOW>;
|
|
debounce-interval = <60>;
|
|
};
|
|
};
|
|
|
|
leds {
|
|
compatible = "gpio-leds";
|
|
|
|
led_system: system {
|
|
label = "blue:system";
|
|
gpios = <&gpio 1 GPIO_ACTIVE_LOW>;
|
|
default-state = "on";
|
|
};
|
|
wlan {
|
|
label = "blue:wlan";
|
|
gpios = <&gpio 0 GPIO_ACTIVE_LOW>;
|
|
};
|
|
wan {
|
|
label = "blue:wan";
|
|
gpios = <&gpio 27 GPIO_ACTIVE_LOW>;
|
|
};
|
|
};
|
|
|
|
reg_usb_vbus: regulator {
|
|
compatible = "regulator-fixed";
|
|
regulator-name = "usb_vbus";
|
|
regulator-min-microvolt = <5000000>;
|
|
regulator-max-microvolt = <5000000>;
|
|
enable-active-high;
|
|
gpio = <&gpio 20 GPIO_ACTIVE_HIGH>;
|
|
};
|
|
};
|
|
|
|
&spi {
|
|
status = "okay";
|
|
num-cs = <1>;
|
|
|
|
flash@0 {
|
|
compatible = "jedec,spi-nor";
|
|
reg = <0>;
|
|
spi-max-frequency = <25000000>;
|
|
|
|
partitions {
|
|
compatible = "fixed-partitions";
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
|
|
uboot: partition@0 {
|
|
reg = <0x0 0x10000>;
|
|
label = "u-boot";
|
|
read-only;
|
|
};
|
|
|
|
bdinfo: partition@10000 {
|
|
reg = <0x10000 0x10000>;
|
|
label = "bdinfo";
|
|
read-only;
|
|
};
|
|
|
|
firmware: partition@20000 {
|
|
compatible = "denx,uimage";
|
|
reg = <0x20000 0xfc0000>;
|
|
label = "firmware";
|
|
};
|
|
|
|
backup: partition@fe0000 {
|
|
reg = <0xfe0000 0x10000>;
|
|
label = "backup";
|
|
read-only;
|
|
};
|
|
|
|
art: partition@ff0000 {
|
|
reg = <0xff0000 0x10000>;
|
|
label = "art";
|
|
read-only;
|
|
};
|
|
};
|
|
};
|
|
};
|
|
|
|
&gpio {
|
|
status = "okay";
|
|
};
|
|
|
|
&uart {
|
|
status = "okay";
|
|
};
|
|
|
|
&usb {
|
|
status = "okay";
|
|
dr_mode = "host";
|
|
vbus-supply = <®_usb_vbus>;
|
|
};
|
|
|
|
&usb_phy {
|
|
status = "okay";
|
|
};
|
|
|
|
ð0 {
|
|
status = "okay";
|
|
|
|
nvmem-cells = <&macaddr_bdinfo_18a>;
|
|
nvmem-cell-names = "mac-address-ascii";
|
|
mac-address-increment = <1>;
|
|
};
|
|
|
|
ð1 {
|
|
status = "okay";
|
|
|
|
nvmem-cells = <&macaddr_bdinfo_18a>;
|
|
nvmem-cell-names = "mac-address-ascii";
|
|
};
|
|
|
|
&wmac {
|
|
status = "okay";
|
|
mtd-cal-data = <&art 0x1000>;
|
|
|
|
nvmem-cells = <&macaddr_bdinfo_18a>;
|
|
nvmem-cell-names = "mac-address-ascii";
|
|
mac-address-increment = <2>;
|
|
};
|
|
|
|
&bdinfo {
|
|
compatible = "nvmem-cells";
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
|
|
macaddr_bdinfo_18a: macaddr@18a {
|
|
reg = <0x18a 0x11>;
|
|
};
|
|
};
|