mirror of
https://github.com/openwrt/openwrt.git
synced 2024-12-23 07:22:33 +00:00
3a4b751110
The uart node is enabled on all devices except one (GL-USB150 *). Thus, let's not have a few hundred nodes to enable it, but do not disable it in the first place. Where the majority of devices is using it, also move the serial0 alias to the DTSI. *) Since GL-USB150 even defines serial0 alias, the missing uart is probably just a mistake. Anyway, disable it for now so this patch stays cosmetic. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
133 lines
2.1 KiB
Plaintext
133 lines
2.1 KiB
Plaintext
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
|
|
|
#include "qca956x.dtsi"
|
|
|
|
#include <dt-bindings/gpio/gpio.h>
|
|
#include <dt-bindings/input/input.h>
|
|
|
|
/ {
|
|
model = "Phicomm K2T";
|
|
compatible = "phicomm,k2t", "qca,qca9563";
|
|
|
|
aliases {
|
|
led-boot = &led_status_red;
|
|
led-failsafe = &led_status_red;
|
|
led-running = &led_status_red;
|
|
led-upgrade = &led_status_red;
|
|
};
|
|
|
|
leds {
|
|
compatible = "gpio-leds";
|
|
|
|
status_blue {
|
|
label = "blue:status";
|
|
gpios = <&gpio 6 GPIO_ACTIVE_LOW>;
|
|
};
|
|
|
|
led_status_red: status_red {
|
|
label = "red:status";
|
|
gpios = <&gpio 7 GPIO_ACTIVE_HIGH>;
|
|
};
|
|
|
|
status_yellow {
|
|
label = "yellow:status";
|
|
gpios = <&gpio 8 GPIO_ACTIVE_LOW>;
|
|
};
|
|
};
|
|
|
|
keys {
|
|
compatible = "gpio-keys";
|
|
|
|
reset {
|
|
linux,code = <KEY_RESTART>;
|
|
gpios = <&gpio 2 GPIO_ACTIVE_LOW>;
|
|
debounce-interval = <60>;
|
|
};
|
|
};
|
|
};
|
|
|
|
&pcie {
|
|
status = "okay";
|
|
};
|
|
|
|
&spi {
|
|
status = "okay";
|
|
|
|
flash@0 {
|
|
compatible = "jedec,spi-nor";
|
|
reg = <0>;
|
|
spi-max-frequency = <25000000>;
|
|
|
|
partitions {
|
|
compatible = "fixed-partitions";
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
|
|
partition@0 {
|
|
label = "u-boot";
|
|
reg = <0x000000 0x30000>;
|
|
read-only;
|
|
};
|
|
|
|
partition@30000 {
|
|
label = "config";
|
|
reg = <0x030000 0x10000>;
|
|
read-only;
|
|
};
|
|
|
|
partition@40000 {
|
|
label = "permanent";
|
|
reg = <0x040000 0x50000>;
|
|
read-only;
|
|
};
|
|
|
|
partition@90000 {
|
|
compatible = "denx,uimage";
|
|
label = "firmware";
|
|
reg = <0x090000 0xf60000>;
|
|
};
|
|
|
|
art: partition@ff0000 {
|
|
label = "art";
|
|
reg = <0xff0000 0x010000>;
|
|
read-only;
|
|
};
|
|
};
|
|
};
|
|
};
|
|
|
|
&mdio0 {
|
|
status = "okay";
|
|
|
|
phy-mask = <0>;
|
|
|
|
phy0: ethernet-phy@0 {
|
|
reg = <0>;
|
|
phy-mode = "sgmii";
|
|
|
|
qca,ar8327-initvals = <
|
|
0x04 0x00080080 /* PORT0 PAD MODE CTRL */
|
|
0x10 0x81000080 /* POWER_ON_STRAP */
|
|
0x50 0xcc35cc35 /* LED_CTRL0 */
|
|
0x54 0xcb37cb37 /* LED_CTRL1 */
|
|
0x58 0x00000000 /* LED_CTRL2 */
|
|
0x5c 0x00f3cf00 /* LED_CTRL3 */
|
|
0x7c 0x0000007e /* PORT0_STATUS */
|
|
>;
|
|
};
|
|
};
|
|
|
|
ð0 {
|
|
status = "okay";
|
|
|
|
pll-data = <0x03000101 0x00000101 0x00001919>;
|
|
|
|
phy-mode = "sgmii";
|
|
phy-handle = <&phy0>;
|
|
};
|
|
|
|
&wmac {
|
|
status = "okay";
|
|
mtd-cal-data = <&art 0x1000>;
|
|
};
|