mirror of
https://github.com/openwrt/openwrt.git
synced 2024-12-23 15:32:33 +00:00
95fe3c51e5
If we need to set the initial output value to GPIOF_OUT_INIT_HIGH (1) to enable something, the pin is ACTIVE_HIGH. The same applies to GPIOF_OUT_INIT_LOW (0) and ACTIVE_LOW. Signed-off-by: Mathias Kresin <dev@kresin.me>
180 lines
2.8 KiB
Plaintext
180 lines
2.8 KiB
Plaintext
/dts-v1/;
|
|
|
|
#include "rt3883.dtsi"
|
|
|
|
#include <dt-bindings/gpio/gpio.h>
|
|
#include <dt-bindings/input/input.h>
|
|
|
|
/ {
|
|
compatible = "edimax,br-6475nd", "ralink,rt3883-soc";
|
|
model = "Edimax BR-6475nD";
|
|
|
|
gpio-keys-polled {
|
|
compatible = "gpio-keys-polled";
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
poll-interval = <100>;
|
|
|
|
reset {
|
|
label = "reset";
|
|
gpios = <&gpio0 7 GPIO_ACTIVE_LOW>;
|
|
linux,code = <KEY_RESTART>;
|
|
};
|
|
|
|
rfkill {
|
|
label = "rfkill";
|
|
gpios = <&gpio0 9 GPIO_ACTIVE_LOW>;
|
|
linux,input-type = <EV_SW>;
|
|
linux,code = <KEY_RFKILL>;
|
|
};
|
|
};
|
|
|
|
gpio-leds {
|
|
compatible = "gpio-leds";
|
|
|
|
power {
|
|
label = "br-6475nd:green:power";
|
|
gpios = <&gpio0 10 GPIO_ACTIVE_LOW>;
|
|
};
|
|
|
|
wlan {
|
|
label = "br-6475nd:amber:wlan";
|
|
gpios = <&gpio0 11 GPIO_ACTIVE_LOW>;
|
|
};
|
|
|
|
wlan_5ghz {
|
|
label = "br-6475nd:amber:wlan_5ghz";
|
|
gpios = <&gpio0 14 GPIO_ACTIVE_LOW>;
|
|
};
|
|
};
|
|
|
|
nor-flash@1c000000 {
|
|
compatible = "cfi-flash";
|
|
reg = <0x1c000000 0x800000>;
|
|
bank-width = <2>;
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
|
|
partition@0 {
|
|
reg = <0x00000000 0x00030000>;
|
|
label = "u-boot";
|
|
read-only;
|
|
};
|
|
|
|
partition@30000 {
|
|
reg = <0x00030000 0x00010000>;
|
|
label = "nvram";
|
|
read-only;
|
|
};
|
|
|
|
factory: partition@40000 {
|
|
reg = <0x00040000 0x00010000>;
|
|
label = "factory";
|
|
read-only;
|
|
};
|
|
|
|
devdata: partition@50000 {
|
|
reg = <0x00050000 0x00020000>;
|
|
label = "devdata";
|
|
read-only;
|
|
};
|
|
|
|
partition@70000 {
|
|
reg = <0x00070000 0x00790000>;
|
|
label = "firmware";
|
|
};
|
|
};
|
|
|
|
rtl8367 {
|
|
compatible = "realtek,rtl8367";
|
|
gpio-sda = <&gpio0 5 GPIO_ACTIVE_HIGH>;
|
|
gpio-sck = <&gpio0 4 GPIO_ACTIVE_HIGH>;
|
|
realtek,extif0 = <1 0 1 1 1 1 1 1 2>;
|
|
};
|
|
|
|
/* Unclear if this is the correct gpio setup; the USB ports are
|
|
unpopulated on a stock BR-6475nD, even though the hardware exists
|
|
and the headers are there. */
|
|
/*
|
|
gpio_export {
|
|
compatible = "gpio-export";
|
|
#size-cells = <0>;
|
|
|
|
usb {
|
|
gpio-export,name="usb";
|
|
gpio-export,output=<0>;
|
|
gpios = <&gpio0 19 GPIO_ACTIVE_LOW>;
|
|
};
|
|
};
|
|
*/
|
|
};
|
|
|
|
&pinctrl {
|
|
state_default: pinctrl0 {
|
|
gpio {
|
|
ralink,group = "spi", "jtag", "uartf";
|
|
ralink,function = "gpio";
|
|
};
|
|
};
|
|
};
|
|
|
|
&timer {
|
|
status = "okay";
|
|
};
|
|
|
|
&gpio1 {
|
|
status = "okay";
|
|
};
|
|
|
|
&uartlite {
|
|
status = "okay";
|
|
};
|
|
|
|
ðernet {
|
|
status = "okay";
|
|
mtd-mac-address = <&devdata 0x0d>;
|
|
|
|
port@0 {
|
|
mediatek,fixed-link = <1000 1 1 1>;
|
|
};
|
|
};
|
|
|
|
&wmac {
|
|
status = "okay";
|
|
ralink,mtd-eeprom = <&factory 0>;
|
|
};
|
|
|
|
&pci {
|
|
status = "okay";
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&pci_pins>;
|
|
|
|
pci_pins: pci {
|
|
pci {
|
|
ralink,group = "pci";
|
|
ralink,function = "pci-fnc";
|
|
};
|
|
};
|
|
|
|
host-bridge {
|
|
pci-bridge@1 {
|
|
status = "okay";
|
|
|
|
wifi@0,0 {
|
|
compatible = "pci0,0";
|
|
reg = <0x10000 0 0 0 0>;
|
|
ralink,5ghz = <0>;
|
|
ralink,mtd-eeprom = <&factory 0x8000>;
|
|
};
|
|
};
|
|
};
|
|
};
|
|
|
|
&ehci {
|
|
status = "okay";
|
|
};
|
|
|
|
&ohci {
|
|
status = "okay";
|
|
};
|