mirror of
https://github.com/openwrt/openwrt.git
synced 2024-12-22 23:12:32 +00:00
21be2c26d5
Hardware specification: SoC: MediaTek MT7986A 4x A53 Flash: ESMT F50L1G41LB 128MB RAM: ESMT M15T4G16256A 512MB Ethernet (Max Speed): XDR4288: 1x 2.5G Wan, 1x 2.5G Lan, 4x 1G Lan XDR6086: 1x 2.5G Wan, 1x 2.5G Lan, 1x 1G Lan XDR6088: 1x 2.5G Wan, 1x 2.5G Lan, 4x 1G Lan WiFi: XDR4288: MT7976DAN (2.4G 2T2R, 5G 3T3R) XDR6086/XDR6088: WiFi1: MT7976GN 2.4GHz 4T4R WiFi2: MT7976AN 5GHz 4T4R Button: Reset, WPS, Turbo USB: 1 x USB 3.0 Power: DC 12V 4A Flash instructions: 1. Execute the following operation to open nc shell: https://openwrt.org/inbox/toh/tp-link/xdr-6086#rooting 2. Replace the stock bootloader to OpenWrt's: dd bs=131072 conv=sync of=/dev/mtdblock9 if=/tmp/xxx-preloader.bin dd bs=131072 conv=sync of=/dev/mtdblock9 seek=28 if=/tmp/xxx-bl31-uboot.fip 3. Connect to your PC via the Gigabit port of the router, set a static ip on the ethernet interface of your PC. (ip 192.168.1.254, gateway 192.168.1.1) 4. Download the initramfs image, and restart the router, waiting for tftp recovery to complete. 5. After openwrt boots up, perform sysupgrade. Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn> [Add uboot build, fit and sysupgrade support, fix RealTek PHYs] Signed-off-by: Daniel Golle <daniel@makrotopia.org>
259 lines
4.5 KiB
Plaintext
259 lines
4.5 KiB
Plaintext
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
|
|
|
#include <dt-bindings/gpio/gpio.h>
|
|
#include <dt-bindings/input/input.h>
|
|
|
|
#include "mt7986a.dtsi"
|
|
|
|
/ {
|
|
aliases {
|
|
serial0 = &uart0;
|
|
label-mac-device = &gmac0;
|
|
led-boot = &led_status_green;
|
|
led-failsafe = &led_status_red;
|
|
led-running = &led_status_green;
|
|
led-upgrade = &led_status_red;
|
|
};
|
|
|
|
chosen {
|
|
stdout-path = "serial0:115200n8";
|
|
};
|
|
|
|
memory {
|
|
reg = <0 0x40000000 0 0x20000000>;
|
|
};
|
|
|
|
reg_3p3v: regulator-3p3v {
|
|
compatible = "regulator-fixed";
|
|
regulator-name = "fixed-3.3V";
|
|
regulator-min-microvolt = <3300000>;
|
|
regulator-max-microvolt = <3300000>;
|
|
regulator-boot-on;
|
|
regulator-always-on;
|
|
};
|
|
|
|
reg_5v: regulator-5v {
|
|
compatible = "regulator-fixed";
|
|
regulator-name = "fixed-5V";
|
|
regulator-min-microvolt = <5000000>;
|
|
regulator-max-microvolt = <5000000>;
|
|
regulator-boot-on;
|
|
regulator-always-on;
|
|
};
|
|
|
|
keys {
|
|
compatible = "gpio-keys";
|
|
|
|
reset {
|
|
label = "reset";
|
|
linux,code = <KEY_RESTART>;
|
|
gpios = <&pio 9 GPIO_ACTIVE_LOW>;
|
|
};
|
|
|
|
wps {
|
|
label = "wps";
|
|
linux,code = <KEY_WPS_BUTTON>;
|
|
gpios = <&pio 10 GPIO_ACTIVE_LOW>;
|
|
};
|
|
|
|
turbo {
|
|
label = "turbo";
|
|
linux,code = <BTN_1>;
|
|
gpios = <&pio 11 GPIO_ACTIVE_LOW>;
|
|
};
|
|
};
|
|
|
|
leds {
|
|
compatible = "gpio-leds";
|
|
|
|
led_status_red: status_red {
|
|
label = "red:status";
|
|
gpios = <&pio 7 GPIO_ACTIVE_HIGH>;
|
|
};
|
|
|
|
led_status_green: status_green {
|
|
label = "green:status";
|
|
gpios = <&pio 8 GPIO_ACTIVE_HIGH>;
|
|
};
|
|
|
|
turbo {
|
|
label = "green:turbo";
|
|
gpios = <&pio 12 GPIO_ACTIVE_HIGH>;
|
|
};
|
|
};
|
|
};
|
|
|
|
ð {
|
|
status = "okay";
|
|
|
|
gmac0: mac@0 {
|
|
compatible = "mediatek,eth-mac";
|
|
reg = <0>;
|
|
phy-mode = "2500base-x";
|
|
|
|
nvmem-cells = <&macaddr_config_1c>;
|
|
nvmem-cell-names = "mac-address";
|
|
|
|
fixed-link {
|
|
speed = <2500>;
|
|
full-duplex;
|
|
pause;
|
|
};
|
|
};
|
|
|
|
gmac1: mac@1 {
|
|
compatible = "mediatek,eth-mac";
|
|
reg = <1>;
|
|
phy-handle = <&phy7>;
|
|
phy-mode = "2500base-x";
|
|
|
|
nvmem-cells = <&macaddr_config_1c>;
|
|
nvmem-cell-names = "mac-address";
|
|
mac-address-increment = <1>;
|
|
};
|
|
|
|
mdio: mdio-bus {
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
};
|
|
};
|
|
|
|
&mdio {
|
|
phy5: ethernet-phy@5 {
|
|
compatible = "ethernet-phy-ieee802.3-c45";
|
|
reg = <5>;
|
|
reset-assert-us = <100000>;
|
|
reset-deassert-us = <100000>;
|
|
reset-gpios = <&pio 13 GPIO_ACTIVE_LOW>;
|
|
realtek,aldps-enable;
|
|
};
|
|
|
|
phy7: ethernet-phy@7 {
|
|
compatible = "ethernet-phy-ieee802.3-c45";
|
|
reg = <7>;
|
|
reset-assert-us = <100000>;
|
|
reset-deassert-us = <100000>;
|
|
reset-gpios = <&pio 17 GPIO_ACTIVE_LOW>;
|
|
realtek,aldps-enable;
|
|
};
|
|
|
|
switch: switch@31 {
|
|
compatible = "mediatek,mt7531";
|
|
reg = <31>;
|
|
reset-gpios = <&pio 5 GPIO_ACTIVE_HIGH>;
|
|
interrupt-controller;
|
|
#interrupt-cells = <1>;
|
|
interrupt-parent = <&pio>;
|
|
interrupts = <66 IRQ_TYPE_LEVEL_HIGH>;
|
|
};
|
|
};
|
|
|
|
&spi0 {
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&spi_flash_pins>;
|
|
status = "okay";
|
|
|
|
flash@0 {
|
|
compatible = "spi-nand";
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
reg = <0>;
|
|
|
|
spi-max-frequency = <20000000>;
|
|
spi-tx-buswidth = <4>;
|
|
spi-rx-buswidth = <4>;
|
|
|
|
partitions {
|
|
compatible = "fixed-partitions";
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
|
|
partition@0 {
|
|
label = "bl2";
|
|
reg = <0x000000 0x0100000>;
|
|
read-only;
|
|
};
|
|
|
|
config: partition@100000 {
|
|
label = "config";
|
|
reg = <0x100000 0x0060000>;
|
|
read-only;
|
|
};
|
|
|
|
factory: partition@160000 {
|
|
label = "factory";
|
|
reg = <0x160000 0x0060000>;
|
|
read-only;
|
|
};
|
|
|
|
partition@1c0000 {
|
|
label = "reserved";
|
|
reg = <0x1c0000 0x01c0000>;
|
|
read-only;
|
|
};
|
|
|
|
partition@380000 {
|
|
label = "fip";
|
|
reg = <0x380000 0x0200000>;
|
|
read-only;
|
|
};
|
|
|
|
partition@580000 {
|
|
label = "ubi";
|
|
reg = <0x580000 0x7800000>;
|
|
};
|
|
};
|
|
};
|
|
};
|
|
|
|
&pio {
|
|
spi_flash_pins: spi-flash-pins-33-to-38 {
|
|
mux {
|
|
function = "spi";
|
|
groups = "spi0", "spi0_wp_hold";
|
|
};
|
|
conf-pu {
|
|
pins = "SPI2_CS", "SPI2_HOLD", "SPI2_WP";
|
|
drive-strength = <8>;
|
|
mediatek,pull-up-adv = <0>; /* bias-disable */
|
|
};
|
|
conf-pd {
|
|
pins = "SPI2_CLK", "SPI2_MOSI", "SPI2_MISO";
|
|
drive-strength = <8>;
|
|
mediatek,pull-down-adv = <0>; /* bias-disable */
|
|
};
|
|
};
|
|
};
|
|
|
|
&ssusb {
|
|
vusb33-supply = <®_3p3v>;
|
|
vbus-supply = <®_5v>;
|
|
status = "okay";
|
|
};
|
|
|
|
&uart0 {
|
|
status = "okay";
|
|
};
|
|
|
|
&usb_phy {
|
|
status = "okay";
|
|
};
|
|
|
|
&wmac {
|
|
mediatek,mtd-eeprom = <&factory 0x0>;
|
|
nvmem-cells = <&macaddr_config_1c>;
|
|
nvmem-cell-names = "mac-address";
|
|
mac-address-increment = <2>;
|
|
status = "okay";
|
|
};
|
|
|
|
&config {
|
|
compatible = "nvmem-cells";
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
|
|
macaddr_config_1c: macaddr@1c {
|
|
reg = <0x1c 0x6>;
|
|
};
|
|
};
|