mirror of
https://github.com/openwrt/openwrt.git
synced 2024-12-25 08:21:14 +00:00
8d9c1087e4
SOC: Qualcomm QCA9556 (Scorpion) 560MHz MIPS74Kc
RAM: 64MB Zentel A3R12E40CBF DDR2
FLASH: 16MiB Winbond W25Q128 SPI NOR
WLAN1: QCA9556 2.4 GHz 802.11b/g/n 3x3
INPUT: WPS button
LED: Power, WiFi, LAN, RSSI indicator
Serial: Header Next to Black metal shield
Pinout is 3.3V - RX - TX - GND (Square Pad is 3.3V)
The Serial setting is 115200-8-N-1.
Installation via EVA:
In the first seconds after Power is connected, the bootloader will
listen for FTP connections on 192.168.178.1. Firmware can be uploaded
like following:
ftp> quote USER adam2
ftp> quote PASS adam2
ftp> binary
ftp> debug
ftp> passive
ftp> quote MEDIA FLSH
ftp> put openwrt-sysupgrade.bin mtd1
Note that this procedure might take up to two minutes.
You need to powercycle the device afterwards to boot OpenWRT.
Tested-by: Andreas Ziegler <dev@andreas-ziegler.de>
Signed-off-by: David Bauer <mail@david-bauer.net>
113 lines
2.0 KiB
Plaintext
113 lines
2.0 KiB
Plaintext
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
|
|
|
#include <dt-bindings/gpio/gpio.h>
|
|
|
|
#include "qca9556_avm_fritz-repeater.dtsi"
|
|
|
|
/ {
|
|
compatible = "avm,fritz1750e", "qca,qca9557";
|
|
model = "AVM FRITZ!WLAN Repeater 1750E";
|
|
|
|
aliases {
|
|
led-boot = &led_power;
|
|
led-failsafe = &led_power;
|
|
led-running = &led_power;
|
|
led-upgrade = &led_power;
|
|
};
|
|
|
|
led_spi {
|
|
compatible = "spi-gpio";
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
|
|
sck-gpios = <&gpio 14 GPIO_ACTIVE_HIGH>;
|
|
mosi-gpios = <&gpio 15 GPIO_ACTIVE_HIGH>;
|
|
num-chipselects = <0>;
|
|
|
|
spi_gpio: led_gpio@0 {
|
|
compatible = "fairchild,74hc595";
|
|
reg = <0>;
|
|
gpio-controller;
|
|
#gpio-cells = <2>;
|
|
registers-number = <1>;
|
|
spi-max-frequency = <10000000>;
|
|
|
|
gpio_latch_bit {
|
|
gpio-hog;
|
|
gpios = <7 GPIO_ACTIVE_HIGH>;
|
|
output-high;
|
|
line-name = "gpio-latch-bit";
|
|
};
|
|
};
|
|
};
|
|
|
|
leds {
|
|
compatible = "gpio-leds";
|
|
|
|
led_power: power {
|
|
label = "fritz1750e:green:power";
|
|
gpios = <&spi_gpio 6 GPIO_ACTIVE_HIGH>;
|
|
};
|
|
|
|
wlan {
|
|
label = "fritz1750e:green:wlan";
|
|
gpios = <&spi_gpio 5 GPIO_ACTIVE_HIGH>;
|
|
linux,default-trigger = "phy1tpt";
|
|
};
|
|
|
|
lan {
|
|
label = "fritz1750e:green:lan";
|
|
gpios = <&gpio 13 GPIO_ACTIVE_HIGH>;
|
|
};
|
|
|
|
rssi0 {
|
|
label = "fritz1750e:green:rssi0";
|
|
gpios = <&spi_gpio 0 GPIO_ACTIVE_HIGH>;
|
|
};
|
|
|
|
rssi1 {
|
|
label = "fritz1750e:green:rssi1";
|
|
gpios = <&spi_gpio 1 GPIO_ACTIVE_HIGH>;
|
|
};
|
|
|
|
rssi2 {
|
|
label = "fritz1750e:green:rssi2";
|
|
gpios = <&spi_gpio 2 GPIO_ACTIVE_HIGH>;
|
|
};
|
|
|
|
rssi3 {
|
|
label = "fritz1750e:green:rssi3";
|
|
gpios = <&spi_gpio 3 GPIO_ACTIVE_HIGH>;
|
|
};
|
|
|
|
rssi4 {
|
|
label = "fritz1750e:green:rssi4";
|
|
gpios = <&spi_gpio 4 GPIO_ACTIVE_HIGH>;
|
|
};
|
|
};
|
|
};
|
|
|
|
&pcie0 {
|
|
status = "okay";
|
|
};
|
|
|
|
&phy0 {
|
|
reset-gpios = <&gpio 11 GPIO_ACTIVE_LOW>;
|
|
};
|
|
|
|
&gpio {
|
|
reset-pcie-ep {
|
|
gpio-hog;
|
|
gpios = <17 GPIO_ACTIVE_HIGH>;
|
|
output-high;
|
|
line-name = "PCIE EP reset";
|
|
};
|
|
|
|
reset-pcie {
|
|
gpio-hog;
|
|
gpios = <18 GPIO_ACTIVE_HIGH>;
|
|
output-high;
|
|
line-name = "PCIE Bus reset";
|
|
};
|
|
};
|