openwrt/target/linux/generic/backport-6.6/790-09-v6.9-net-dsa-mt7530-improve-code-path-for-setting-up-port.patch
John Audia 5efd41c10b kernel: bump 6.6 to 6.6.28
Changelog: https://cdn.kernel.org/pub/linux/kernel/v6.x/ChangeLog-6.6.28

Removed upstream:
	pending-6.6/796-net-dsa-mt7530-trap-link-local-frames-regardless-of-.patch

All oither patches automatically rebased.

1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.6.28&id=8b6c4b62582606c62074a7e7c64156f56d2785f2

Build system: x86/64
Build-tested: x86/64/AMD Cezanne, flogic/xiaomi_redmi-router-ax6000-ubootmod, ramips/tplink_archer-a6-v3
Run-tested: x86/64/AMD Cezanne, flogic/xiaomi_redmi-router-ax6000-ubootmod, ramips/tplink_archer-a6-v3

Signed-off-by: John Audia <therealgraysky@proton.me>
2024-04-23 22:38:05 +02:00

96 lines
3.1 KiB
Diff
Raw Blame History

This file contains ambiguous Unicode characters

This file contains Unicode characters that might be confused with other characters. If you think that this is intentional, you can safely ignore this warning. Use the Escape button to reveal them.

From c1b2294a9b4b9b6c0cbe58666cb86e0a9cb0abfd Mon Sep 17 00:00:00 2001
From: =?UTF-8?q?Ar=C4=B1n=C3=A7=20=C3=9CNAL?= <arinc.unal@arinc9.com>
Date: Mon, 22 Jan 2024 08:35:56 +0300
Subject: [PATCH 09/30] net: dsa: mt7530: improve code path for setting up port
5
MIME-Version: 1.0
Content-Type: text/plain; charset=UTF-8
Content-Transfer-Encoding: 8bit
There're two code paths for setting up port 5:
mt7530_setup()
-> mt7530_setup_port5()
mt753x_phylink_mac_config()
-> mt753x_mac_config()
-> mt7530_mac_config()
-> mt7530_setup_port5()
Currently mt7530_setup_port5() from mt7530_setup() always runs. If port 5
is used as a CPU, DSA, or user port, mt7530_setup_port5() from
mt753x_phylink_mac_config() won't run. That is because priv->p5_interface
set on mt7530_setup_port5() will match state->interface on
mt753x_phylink_mac_config() which will stop running mt7530_setup_port5()
again.
Therefore, mt7530_setup_port5() will never run from
mt753x_phylink_mac_config().
Address this by not running mt7530_setup_port5() from mt7530_setup() if
port 5 is used as a CPU, DSA, or user port. This driver isn't in the
dsa_switches_apply_workarounds[] array so phylink will always be present.
To keep the cases where port 5 isn't controlled by phylink working as
before, preserve the mt7530_setup_port5() call from mt7530_setup().
Do not set priv->p5_intf_sel to P5_DISABLED. It is already set to that when
"priv" is allocated.
Move setting the interface to a more specific location. It's supposed to be
overwritten if PHY muxing is detected.
Improve the comment which explains the process.
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/20240122-for-netnext-mt7530-improvements-1-v3-5-042401f2b279@arinc9.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
---
drivers/net/dsa/mt7530.c | 17 ++++++++---------
1 file changed, 8 insertions(+), 9 deletions(-)
--- a/drivers/net/dsa/mt7530.c
+++ b/drivers/net/dsa/mt7530.c
@@ -2523,16 +2523,15 @@ mt7530_setup(struct dsa_switch *ds)
return ret;
/* Setup port 5 */
- priv->p5_intf_sel = P5_DISABLED;
- interface = PHY_INTERFACE_MODE_NA;
-
if (!dsa_is_unused_port(ds, 5)) {
priv->p5_intf_sel = P5_INTF_SEL_GMAC5;
- ret = of_get_phy_mode(dsa_to_port(ds, 5)->dn, &interface);
- if (ret && ret != -ENODEV)
- return ret;
} else {
- /* Scan the ethernet nodes. look for GMAC1, lookup used phy */
+ /* Scan the ethernet nodes. Look for GMAC1, lookup the used PHY.
+ * Set priv->p5_intf_sel to the appropriate value if PHY muxing
+ * is detected.
+ */
+ interface = PHY_INTERFACE_MODE_NA;
+
for_each_child_of_node(dn, mac_np) {
if (!of_device_is_compatible(mac_np,
"mediatek,eth-mac"))
@@ -2563,6 +2562,8 @@ mt7530_setup(struct dsa_switch *ds)
of_node_put(phy_node);
break;
}
+
+ mt7530_setup_port5(ds, interface);
}
#ifdef CONFIG_GPIOLIB
@@ -2573,8 +2574,6 @@ mt7530_setup(struct dsa_switch *ds)
}
#endif /* CONFIG_GPIOLIB */
- mt7530_setup_port5(ds, interface);
-
/* Flush the FDB table */
ret = mt7530_fdb_cmd(priv, MT7530_FDB_FLUSH, NULL);
if (ret < 0)