openwrt/target/linux/ramips/dts/mt7621_wavlink_ws-wn572hp3-4g.dts
Jan-Niklas Burfeind dce66899bf ramips: add support for Wavlink WS-WN572HP3 4G
Wavlink WS-WN572HP3 4G is an 802.11ac
dual-band outdoor router with LTE support.

Specifications;
* Soc: MT7621DAT
* RAM: 128MiB
* Flash: NOR 16MiB GD-25Q128ESIG3
* Wi-Fi:
  * MT7613BEN: 5GHz
  * MT7603EN: 2.4GHz
* Ethernet: 2x 1GbE
* USB: None - only used internally
* LTE Modem: Quectel EC200T-EU
* UART: 115200 baud
* LEDs:
  * 7 blue at the front
    * 1 Power
    * 2 LAN / WAN
    * 1 Status
    * 3 RSSI (annotated 4G)
  * 1 green at the bottom (4G LED)
* Buttons: 1 reset button

Installation:
* press and hold the reset button while powering on the device
* keep it pressed for ten seconds
* connect to 192.168.10.1 via webbrowser (chromium/chrome works, at
  least Firefox 106.0.3 does not)
* upload the sysupgrade image, confirm the checksum, wait 2 minutes
  until the device reboots

Revert to stock firmware:
* same as installation but use the recovery image for WL-WN572HP3

Signed-off-by: Jan-Niklas Burfeind <git@aiyionpri.me>
Acked-by: Arınç ÜNAL <arinc.unal@arinc9.com>
2022-12-07 12:30:45 +01:00

185 lines
2.8 KiB
Plaintext

// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
#include "mt7621.dtsi"
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>
/ {
compatible = "wavlink,ws-wn572hp3-4g", "mediatek,mt7621-soc";
model = "Wavlink WS-WN572HP3 4G";
chosen {
bootargs = "console=ttyS0,115200";
};
aliases {
label-mac-device = &wifi1;
led-boot = &led_status_blue;
led-failsafe = &led_status_blue;
led-running = &led_status_blue;
led-upgrade = &led_status_blue;
};
keys {
compatible = "gpio-keys";
reset {
label = "Reset Button";
gpios = <&gpio 18 GPIO_ACTIVE_LOW>;
linux,code = <KEY_RESTART>;
};
};
leds {
compatible = "gpio-leds";
rssihigh {
label = "blue:rssihigh";
gpios = <&gpio 4 GPIO_ACTIVE_LOW>;
};
rssimedium {
label = "blue:rssimedium";
gpios = <&gpio 17 GPIO_ACTIVE_LOW>;
};
rssilow {
label = "blue:rssilow";
gpios = <&gpio 16 GPIO_ACTIVE_LOW>;
};
led_status_blue: status_blue {
label = "blue:status";
gpios = <&gpio 3 GPIO_ACTIVE_LOW>;
};
// gpio 15 would be Quectels PWRKEY if used
};
};
&spi0 {
status = "okay";
flash@0 {
compatible = "jedec,spi-nor";
reg = <0>;
spi-max-frequency = <40000000>;
partitions {
compatible = "fixed-partitions";
#address-cells = <1>;
#size-cells = <1>;
partition@0 {
label = "u-boot";
reg = <0x0 0x30000>;
read-only;
};
partition@30000 {
label = "config";
reg = <0x30000 0x10000>;
read-only;
};
factory: partition@40000 {
label = "factory";
reg = <0x40000 0x10000>;
read-only;
};
partition@50000 {
compatible = "denx,fit";
label = "firmware";
reg = <0x50000 0xf30000>;
};
partition@f00000 {
label = "vendor";
reg = <0xf80000 0x80000>;
read-only;
};
};
};
};
&pcie {
status = "okay";
};
&pcie0 {
wifi0: mt76@0,0 {
compatible = "mediatek,mt76";
reg = <0x0000 0 0 0 0>;
mediatek,mtd-eeprom = <&factory 0x0>;
};
};
&pcie1 {
wifi1: mt76@0,0 {
compatible = "mediatek,mt76";
reg = <0x0000 0 0 0 0>;
mediatek,mtd-eeprom = <&factory 0x8000>;
};
};
&gmac0 {
nvmem-cells = <&macaddr_factory_e000>;
nvmem-cell-names = "mac-address";
};
&gmac1 {
status = "okay";
label = "wan";
phy-handle = <&ethphy4>;
nvmem-cells = <&macaddr_factory_e006>;
nvmem-cell-names = "mac-address";
};
&mdio {
ethphy4: ethernet-phy@4 {
reg = <4>;
};
};
&switch0 {
ports {
port@1 {
status = "okay";
label = "lan";
};
};
};
&state_default {
gpio {
groups = "wdt";
function = "gpio";
};
};
&factory {
compatible = "nvmem-cells";
#address-cells = <1>;
#size-cells = <1>;
macaddr_factory_e000: macaddr@e000 {
reg = <0xe000 0x6>;
};
macaddr_factory_e006: macaddr@e006 {
reg = <0xe006 0x6>;
};
};
&wifi0{
ieee80211-freq-limit = <2400000 2500000>;
};
&wifi1{
ieee80211-freq-limit = <5000000 6000000>;
};