openwrt/target/linux/realtek/dts-5.15/rtl8380_engenius_ews2910p.dts

// SPDX-License-Identifier: GPL-2.0-or-later

#include "rtl838x.dtsi"

#include <dt-bindings/input/input.h>
#include <dt-bindings/gpio/gpio.h>

/ {
	compatible = "engenius,ews2910p", "realtek,rtl838x-soc";
	model = "EnGenius EWS2910P";

	aliases {
		led-boot = &led_power;
		led-failsafe = &led_fault;
		led-running = &led_power;
		led-upgrade = &led_power;
	};

	memory@0 {
		device_type = "memory";
		reg = <0x0 0x10000000>;
	};

	keys {
		compatible = "gpio-keys";

		reset {
			label = "reset";
			gpios = <&gpio0 11 GPIO_ACTIVE_LOW>;
			linux,code = <KEY_RESTART>;
		};

		led_mode {
			label = "led-mode";
			gpios = <&gpio0 13 GPIO_ACTIVE_LOW>;
			linux,code = <BTN_0>;
		};
	};

	gpio1: rtl8231-gpio {
		compatible = "realtek,rtl8231-gpio";
		#gpio-cells = <2>;
		gpio-controller;
		indirect-access-bus-id = <0>;

		poe_enable {
			gpio-hog;
			gpios = <1 GPIO_ACTIVE_HIGH>;
			output-high;
			line-name = "poe-enable";
		};

		sff_p9_gpios {
			gpio-hog;
			gpios = < 6 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>,
				< 11 GPIO_ACTIVE_HIGH>, /* los-gpio */
				< 12 GPIO_ACTIVE_LOW>;   /* mod-def0-gpio */
			input;
			line-name = "sff-p9-gpios";
		};
	};

	gpio-export {
		compatible = "gpio-export";

		sff-p9-tx-disable {
			gpio-export,name = "sff-p9-tx-disable";
			gpio-export,output = <1>;
			gpios = <&gpio1 10 GPIO_ACTIVE_HIGH>;
		};
	};

	gpio-restart {
		compatible = "gpio-restart";
		gpios = <&gpio1 0 GPIO_ACTIVE_LOW>;
	};

	leds {
		compatible = "gpio-leds";

		led_power: led-0 {
			label = "green:power";
			gpios = <&gpio1 3 GPIO_ACTIVE_LOW>;
		};

		led_lan_mode: led-1 {
			label = "green:lan-mode";
			gpios = <&gpio1 4 GPIO_ACTIVE_LOW>;
		};

		led_fault: led-2 {
			label = "amber:fault";
			gpios = <&gpio1 2 GPIO_ACTIVE_LOW>;
		};

		led_poe_max: led-3 {
			label = "amber:poe-max";
			gpios = <&gpio0 12 GPIO_ACTIVE_LOW>;
		};
	};

	i2c1: i2c-gpio-1 {
		compatible = "i2c-gpio";
		sda-gpios = <&gpio1 7 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
		scl-gpios = <&gpio1 31 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
		i2c-gpio,delay-us = <2>;
		#address-cells = <1>;
		#size-cells = <0>;
	};
	sfp1: sfp-p10 {
		compatible = "sff,sfp";
		i2c-bus = <&i2c1>;
		tx-disable-gpio = <&gpio1 13 GPIO_ACTIVE_HIGH>;
		los-gpio = <&gpio1 14 GPIO_ACTIVE_HIGH>;
		mod-def0-gpio = <&gpio1 21 GPIO_ACTIVE_LOW>;
	};
};

&spi0 {
	status = "okay";

	flash@0 {
		compatible = "jedec,spi-nor";
		reg = <0>;
		spi-max-frequency = <10000000>;

		partitions {
			compatible = "fixed-partitions";
			#address-cells = <1>;
			#size-cells = <1>;

			partition@0 {
				label = "u-boot";
				reg = <0x0 0x80000>;
				read-only;
			};
			partition@80000 {
				label = "u-boot-env";
				reg = <0x80000 0x10000>;
				read-only;
			};
			partition@90000 {
				label = "u-boot-env2";
				reg = <0x90000 0x10000>;
			};
			partition@a0000 {
				label = "rootfs_data";
				reg = <0xa0000 0xd60000>;
			};
			partition@e00000 {
				label = "jffs2-log";
				reg = <0xe00000 0x200000>;
			};
			partition@1000000 {
				compatible = "openwrt,uimage";
				label = "firmware";
				reg = <0x1000000 0x800000>;
				openwrt,ih-magic = <0x03802910>;
			};
			partition@1800000 {
				label = "firmware2";
				reg = <0x1800000 0x800000>;
			};
		};
	};
};

&ethernet0 {
	mdio: mdio-bus {
		compatible = "realtek,rtl838x-mdio";
		regmap = <&ethernet0>;
		#address-cells = <1>;
		#size-cells = <0>;

		INTERNAL_PHY(8)
		INTERNAL_PHY(9)
		INTERNAL_PHY(10)
		INTERNAL_PHY(11)
		INTERNAL_PHY(12)
		INTERNAL_PHY(13)
		INTERNAL_PHY(14)
		INTERNAL_PHY(15)

		INTERNAL_PHY(24)
		INTERNAL_PHY(26)
	};
};

&switch0 {
	ports {
		#address-cells = <1>;
		#size-cells = <0>;

		SWITCH_PORT(8, 1, internal)
		SWITCH_PORT(9, 2, internal)
		SWITCH_PORT(10, 3, internal)
		SWITCH_PORT(11, 4, internal)
		SWITCH_PORT(12, 5, internal)
		SWITCH_PORT(13, 6, internal)
		SWITCH_PORT(14, 7, internal)
		SWITCH_PORT(15, 8, internal)

		SWITCH_SFP_PORT(24, 9, 1000base-x)

		port@26 {
			reg = <26>;
			label = "lan10";
			phy-mode = "1000base-x";
			phy-handle = <&phy26>;
			managed = "in-band-status";
			sfp = <&sfp1>;
		};

		port@28 {
			ethernet = <&ethernet0>;
			reg = <28>;
			phy-mode = "internal";

			fixed-link {
				speed = <1000>;
				full-duplex;
			};
		};
	};
};

&uart1 {
	status = "okay";
};